Ahmed M. Gomaa
Research Subjects
Research Interests
Ahmed M. Gomaa has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Hisham A. Nasr-El-Din
Professor Texas A&M University, College Station, TX 77843
2 shared publications - Mohamed Mahmoud
Department of Petroleum Engineering, College of Petroleum Engineering & Geosciences, King Fahd University of Petroleum and Minerals, Dhahran, Saudi Arabia
1 shared publication
Latest Publications
- 26 May 2011
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 133 (2) , 023101
Propagation of Regular HCl Acids in Carbonate Rocks: The Impact of an In Situ Gelled Acid Stage
Recent laboratory and field studies indicated that polymer-based in situ gelled acids can cause formation damage. Coreflood experiments using single-stage and multistage acids were conducted at 250 °F. 15 wt. % regular HCl and 5 wt. % in situ gelled acid-based on Fe(III) as a crosslinker were the acids that were used in this study. Propagation of acids and crosslinker inside 20 in. long cores was examined for the first time in detail. Stage volume and injection rate, which were the parameters that affect the propagating of various chemical species, were examined. Samples of the core effluent were collected and the concentrations of calcium, crosslinker, and acid were measured. Material balance was conducted to determine the amount of cross-liker that retained in the core. The results show that in situ gelled acid should be pumped at low injection rates. In situ gelled acid at low injection rate instantaneously plugged the tip of the wormhole and did not create additional wormholes inside the core. Therefore, when the final regular acid stage bypassed the gel, it started to propagate from nearly the last point that the first stage ended. In site gelled acid stage volume should not exceed 0.5 PV. No benefits were gained by increasing the volume of in situ gelled acids. Retention of total iron in the core increased in multistage acid treatments, especially at low acid injection rates.
- 26 May 2011
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 133 (2) , 023101
Propagation of Regular HCl Acids in Carbonate Rocks: The Impact of an In Situ Gelled Acid Stage
Recent laboratory and field studies indicated that polymer-based in situ gelled acids can cause formation damage. Coreflood experiments using single-stage and multistage acids were conducted at 250 °F. 15 wt. % regular HCl and 5 wt. % in situ gelled acid-based on Fe(III) as a crosslinker were the acids that were used in this study. Propagation of acids and crosslinker inside 20 in. long cores was examined for the first time in detail. Stage volume and injection rate, which were the parameters that affect the propagating of various chemical species, were examined. Samples of the core effluent were collected and the concentrations of calcium, crosslinker, and acid were measured. Material balance was conducted to determine the amount of cross-liker that retained in the core. The results show that in situ gelled acid should be pumped at low injection rates. In situ gelled acid at low injection rate instantaneously plugged the tip of the wormhole and did not create additional wormholes inside the core. Therefore, when the final regular acid stage bypassed the gel, it started to propagate from nearly the last point that the first stage ended. In site gelled acid stage volume should not exceed 0.5 PV. No benefits were gained by increasing the volume of in situ gelled acids. Retention of total iron in the core increased in multistage acid treatments, especially at low acid injection rates.
- 26 January 2011
- Published by Society of Petroleum Engineers (SPE) in SPE Production & Operations
- Vol. 26 (01) , 41-54
Effect of Shear Rate on the Propagation of Polymer-Based In-Situ-Gelled Acids Inside Carbonate Cores
Summary: In-situ-gelled acids that are based on polymers have been used in the field for several years and were the subject of many laboratory studies. An extensive literature survey reveals that there are conflicting opinions about using these acids. These acids were used in the field with mixed results. Recent laboratory work indicated that these acids can cause damage under certain conditions. There is no agreement on when this system can be applied successfully in the field. A coreflood study was conducted using Indiana limestone cores (1.5-in. diameter and 20-in. length) at high temperatures and pressures. Propagation of the acid, polymer, and crosslinker inside the long cores was examined in detail. Samples of the core effluent were collected, and the concentrations of calcium, crosslinker, and acid were measured. Permeability enhancement and location of any precipitation was detected using a computed-tomagraphy (CT) scanner on the core before and after the acid injection. Different sections were cut from the core to investigate the propagation and precipitation of polymer and crosslinker. Material balance was conducted to determine the amount of crosslinker retained in the core. Experimental results show that this acid system caused damage in some cases. At low shear rates, in-situ-gelled acid formed a gel inside the core as indicated by the cyclic behavior noted in the pressure drop across the core, and the acid changed direction inside the core several times. However, this gel reduced the core permeability significantly. At high shear rates, a smaller amount of gel was formed inside the core, and the acid's ability to change its direction inside the core was less than that noted at low shear rate. A significant permeability enhancement was achieved. The wormhole length increased as the shear rate was increased, while the diameter of the wormhole increased as the cumulative injected volume of acid increased. CT scan indicated the presence of gel residue inside and around the wormhole. Gel residue increased at low shear rates. Material balance performed on the crosslinker indicated that a significant amount of the crosslinker was retained in the core. This amount increased at low shear rates.
- 26 January 2011
- Published by Society of Petroleum Engineers (SPE) in SPE Production & Operations
- Vol. 26 (01) , 41-54
Effect of Shear Rate on the Propagation of Polymer-Based In-Situ-Gelled Acids Inside Carbonate Cores
Summary: In-situ-gelled acids that are based on polymers have been used in the field for several years and were the subject of many laboratory studies. An extensive literature survey reveals that there are conflicting opinions about using these acids. These acids were used in the field with mixed results. Recent laboratory work indicated that these acids can cause damage under certain conditions. There is no agreement on when this system can be applied successfully in the field. A coreflood study was conducted using Indiana limestone cores (1.5-in. diameter and 20-in. length) at high temperatures and pressures. Propagation of the acid, polymer, and crosslinker inside the long cores was examined in detail. Samples of the core effluent were collected, and the concentrations of calcium, crosslinker, and acid were measured. Permeability enhancement and location of any precipitation was detected using a computed-tomagraphy (CT) scanner on the core before and after the acid injection. Different sections were cut from the core to investigate the propagation and precipitation of polymer and crosslinker. Material balance was conducted to determine the amount of crosslinker retained in the core. Experimental results show that this acid system caused damage in some cases. At low shear rates, in-situ-gelled acid formed a gel inside the core as indicated by the cyclic behavior noted in the pressure drop across the core, and the acid changed direction inside the core several times. However, this gel reduced the core permeability significantly. At high shear rates, a smaller amount of gel was formed inside the core, and the acid's ability to change its direction inside the core was less than that noted at low shear rate. A significant permeability enhancement was achieved. The wormhole length increased as the shear rate was increased, while the diameter of the wormhole increased as the cumulative injected volume of acid increased. CT scan indicated the presence of gel residue inside and around the wormhole. Gel residue increased at low shear rates. Material balance performed on the crosslinker indicated that a significant amount of the crosslinker was retained in the core. This amount increased at low shear rates.