Alexandre Tallaire
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alexandre Tallaire has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
A. Gicquel
Laboratoire des Sciences des Procédés et des Matériaux (LSPM) Université Paris 13 Sorbonne Paris Cité CNRS 93430 Villetaneuse France
5 shared publications- Jocelyn Achard
LSPM, CNRS, Universite Sorbonne Paris Nord, 99 Avenue JB Clement, Villetaneuse 93460, France
5 shared publications J. Achard
Laboratoire des Sciences des Procédés et des Matériaux (LSPM) Université Paris 13 Sorbonne Paris Cité CNRS 93430 Villetaneuse France
3 shared publicationsM. Lesik
Laboratoire Aimé Cotton CNRS Université Paris-Sud and ENS Cachan 91405 Orsay France
3 shared publicationsOvidiu Brinza
Laboratoire des Sciences des Procédés et des Matériaux (LSPM), CNRS, Université Paris 13, Sorbonne Paris Cité, 99 avenue J.B. Clément, 93430, Villetaneuse, France
3 shared publications- V. Jacques
Laboratoire Aimé Cotton CNRS Université Paris-Sud and Ecole Normale Supérieure de Cachan 91405 Orsay France
3 shared publications
Latest Publications
- 20 February 2017
- Published by Wiley in Advanced Materials
- Vol. 29 (16)
Reduction of Dislocations in Single Crystal Diamond by Lateral Growth over a Macroscopic Hole
A low-dislocation diamond is obtained by homoepitaxial chemical vapor deposition on a standard moderate-quality substrate hollowed out by a large square hole. Dislocations are found to propagate vertically and horizontally from the substrate and to terminate at the top surface or at the sides of the hole, thus leaving the central part with a strongly reduced dislocation density.
- 20 February 2017
- Published by Wiley in Advanced Materials
- Vol. 29 (16)
Reduction of Dislocations in Single Crystal Diamond by Lateral Growth over a Macroscopic Hole
A low-dislocation diamond is obtained by homoepitaxial chemical vapor deposition on a standard moderate-quality substrate hollowed out by a large square hole. Dislocations are found to propagate vertically and horizontally from the substrate and to terminate at the top surface or at the sides of the hole, thus leaving the central part with a strongly reduced dislocation density.
- 13 April 2016
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 16 (5) , 2741-2746
Identification of Dislocations in Synthetic Chemically Vapor Deposited Diamond Single Crystals
- 13 April 2016
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 16 (5) , 2741-2746
Identification of Dislocations in Synthetic Chemically Vapor Deposited Diamond Single Crystals
- Open Access
Preferential orientation of NV defects in CVD diamond films grown on (113) substrates
Thick CVD diamond layers were successfully grown on (113)-oriented substrates. They exhibited smooth surface morphologies and a crystalline quality comparable to (100) electronic grade material, and much better than (111)-grown layers. High growth rates (15-50 {\mu}m/h) were obtained while nitrogen doping could be achieved in a fairly wide range without seriously imparting crystalline quality. Electron spin resonance measurements were carried out to determine NV centers orientation and concluded that one specific orientation has an occurrence probability of 73 % when (100)-grown layers show an equal distribution in the 4 possible directions. A spin coherence time of around 270 {\mu}s was measured which is equivalent to that reported for material with similar isotopic purity. Although a higher degree of preferential orientation was achieved with (111)-grown layers (almost 100 %), the ease of growth and post-processing of the (113) orientation make it a potentially useful material for magnetometry or other quantum mechanical applications.
Open AccessPreferential orientation of NV defects in CVD diamond films grown on (113) substrates
Thick CVD diamond layers were successfully grown on (113)-oriented substrates. They exhibited smooth surface morphologies and a crystalline quality comparable to (100) electronic grade material, and much better than (111)-grown layers. High growth rates (15-50 {\mu}m/h) were obtained while nitrogen doping could be achieved in a fairly wide range without seriously imparting crystalline quality. Electron spin resonance measurements were carried out to determine NV centers orientation and concluded that one specific orientation has an occurrence probability of 73 % when (100)-grown layers show an equal distribution in the 4 possible directions. A spin coherence time of around 270 {\mu}s was measured which is equivalent to that reported for material with similar isotopic purity. Although a higher degree of preferential orientation was achieved with (111)-grown layers (almost 100 %), the ease of growth and post-processing of the (113) orientation make it a potentially useful material for magnetometry or other quantum mechanical applications.
- Open Access
Temperature dependent creation of nitrogen-vacancy centers in CVD diamond layers
In this work, we explore the ability of plasma assisted chemical vapor deposition (PACVD) operating under high power densities to produce thin high-quality diamond layers with a controlled doping with negatively-charged nitrogen-vacancy (NV-) centers. This luminescent defect possesses specific physical characteristics that make it suitable as an addressable solid-state electron spin for measuring magnetic fields with unprecedented sensitivity. To this aim, a relatively large number of NV- centers (> 10^12 cm^-3) should ideally be located in a thin diamond layer (a few tens of nm) close to the surface which is particularly challenging to achieve with the PACVD technique. Here we show that intentional temperature variations can be exploited to tune NV- creation efficiency during growth, allowing engineering complex stacking structures with a variable doping. Because such a temperature variation can be performed quickly and without any change of the gas phase composition, thin layers can be grown. Measurements show that despite the temperature variations, the luminescent centers incorporated using this technique exhibit spin coherence properties similar to those reached in ultra-pure bulk crystals, which suggests that they could be successfully employed in magnetometry applications.
Open AccessTemperature dependent creation of nitrogen-vacancy centers in CVD diamond layers
In this work, we explore the ability of plasma assisted chemical vapor deposition (PACVD) operating under high power densities to produce thin high-quality diamond layers with a controlled doping with negatively-charged nitrogen-vacancy (NV-) centers. This luminescent defect possesses specific physical characteristics that make it suitable as an addressable solid-state electron spin for measuring magnetic fields with unprecedented sensitivity. To this aim, a relatively large number of NV- centers (> 10^12 cm^-3) should ideally be located in a thin diamond layer (a few tens of nm) close to the surface which is particularly challenging to achieve with the PACVD technique. Here we show that intentional temperature variations can be exploited to tune NV- creation efficiency during growth, allowing engineering complex stacking structures with a variable doping. Because such a temperature variation can be performed quickly and without any change of the gas phase composition, thin layers can be grown. Measurements show that despite the temperature variations, the luminescent centers incorporated using this technique exhibit spin coherence properties similar to those reached in ultra-pure bulk crystals, which suggests that they could be successfully employed in magnetometry applications.
- Open Access
Perfect preferential orientation of nitrogen-vacancy defects in a synthetic diamond sample
We show that the orientation of nitrogen-vacancy (NV) defects in diamond can be efficiently controlled through chemical vapor deposition (CVD) growth on a (111)-oriented diamond substrate. More precisely, we demonstrate that spontaneously generated NV defects are oriented with a ~ 97 % probability along the [111] axis, corresponding to the most appealing orientation among the four possible crystallographic axes. Such a nearly perfect preferential orientation is explained by analyzing the diamond growth mechanism on a (111)-oriented substrate and could be extended to other types of defects. This work is a significant step towards the design of optimized diamond samples for quantum information and sensing applications.
Open AccessPerfect preferential orientation of nitrogen-vacancy defects in a synthetic diamond sample
We show that the orientation of nitrogen-vacancy (NV) defects in diamond can be efficiently controlled through chemical vapor deposition (CVD) growth on a (111)-oriented diamond substrate. More precisely, we demonstrate that spontaneously generated NV defects are oriented with a ~ 97 % probability along the [111] axis, corresponding to the most appealing orientation among the four possible crystallographic axes. Such a nearly perfect preferential orientation is explained by analyzing the diamond growth mechanism on a (111)-oriented substrate and could be extended to other types of defects. This work is a significant step towards the design of optimized diamond samples for quantum information and sensing applications.
- 24 July 2013
- Published by Wiley in Physica Status Solidi (a)
- Vol. 210 (10) , 1985-1990
Influence of surface misorientation of HPHT diamond substrates on crystal morphologies and threading dislocations propagation
The production of diamond‐based electronic devices for optical and electronic applications requires the control of point and extended defects that influence the exceptional properties of the material. While point defects in single crystal (Chemical Vapor Deposition) diamond have been studied for many years, relatively little has been reported on the extended defects content of this material. In particular, threading dislocations propagating parallel to the growth direction, act as killer defects within the CVD diamond film. In this work, different substrate surface misorientations have been investigated to evaluate their effect on dislocation propagation. Misorientation angles of 3.5°, 10°, and 20° along and directions as well as bevels of 10° along and directions were used. By using misorientations of 10° or above along the directions it is possible to plasma etch the substrate surface prior to growth while keeping a smooth morphology. This affects defect density in the CVD film after growth and helps decreasing threading dislocations. In parallel, a growth model allowed us to predict the evolution of the top misoriented face and the crystal shape. This study aims at getting a better understanding of dislocations formation and propagation in order to prepare defect‐free CVD diamond films.
- 24 July 2013
- Published by Wiley in Physica Status Solidi (a)
- Vol. 210 (10) , 1985-1990
Influence of surface misorientation of HPHT diamond substrates on crystal morphologies and threading dislocations propagation
The production of diamond‐based electronic devices for optical and electronic applications requires the control of point and extended defects that influence the exceptional properties of the material. While point defects in single crystal (Chemical Vapor Deposition) diamond have been studied for many years, relatively little has been reported on the extended defects content of this material. In particular, threading dislocations propagating parallel to the growth direction, act as killer defects within the CVD diamond film. In this work, different substrate surface misorientations have been investigated to evaluate their effect on dislocation propagation. Misorientation angles of 3.5°, 10°, and 20° along and directions as well as bevels of 10° along and directions were used. By using misorientations of 10° or above along the directions it is possible to plasma etch the substrate surface prior to growth while keeping a smooth morphology. This affects defect density in the CVD film after growth and helps decreasing threading dislocations. In parallel, a growth model allowed us to predict the evolution of the top misoriented face and the crystal shape. This study aims at getting a better understanding of dislocations formation and propagation in order to prepare defect‐free CVD diamond films.
- 23 July 2012
- Published by Wiley in Physica Status Solidi (a)
- Vol. 209 (9) , 1715-1720
Etch‐pit formation mechanism induced on HPHT and CVD diamond single crystals by H2/O2 plasma etching treatment
H2/O2 plasma treatments offer advantages over other etching processes of diamond as a technique to prepare the substrate surface prior to chemical vapor deposition (CVD) diamond growth. It allows removing defects induced on the surface by polishing, thus leading to an improved morphology and limiting the stress within the grown crystal. Moreover, they present the advantage to be performed in situ just before the CVD diamond growth. In this work, H2/O2 plasma treatments were performed so that threading dislocations and other defects are etched preferentially, thus leaving typical etch‐pits. The defect densities in several high pressure high temperature (HPHT) and CVD diamond crystals were then quantified and compared; in particular defects originating from polishing could be distinguished from extended defects inside the crystal. Furthermore, the defect density was found to be of the order of 105/cm2 for HPHT crystals, which was approximately one order of magnitude lower than that measured in low cost commercial CVD monocrystals. The use of laser microscopy also allowed observing the morphology, size and depth of different etch‐pits of 〈001〉‐oriented and misoriented crystals and their evolution with etching time in order to get a better understanding of defect density and formation during CVD growth.
- 23 July 2012
- Published by Wiley in Physica Status Solidi (a)
- Vol. 209 (9) , 1715-1720
Etch‐pit formation mechanism induced on HPHT and CVD diamond single crystals by H2/O2 plasma etching treatment
H2/O2 plasma treatments offer advantages over other etching processes of diamond as a technique to prepare the substrate surface prior to chemical vapor deposition (CVD) diamond growth. It allows removing defects induced on the surface by polishing, thus leading to an improved morphology and limiting the stress within the grown crystal. Moreover, they present the advantage to be performed in situ just before the CVD diamond growth. In this work, H2/O2 plasma treatments were performed so that threading dislocations and other defects are etched preferentially, thus leaving typical etch‐pits. The defect densities in several high pressure high temperature (HPHT) and CVD diamond crystals were then quantified and compared; in particular defects originating from polishing could be distinguished from extended defects inside the crystal. Furthermore, the defect density was found to be of the order of 105/cm2 for HPHT crystals, which was approximately one order of magnitude lower than that measured in low cost commercial CVD monocrystals. The use of laser microscopy also allowed observing the morphology, size and depth of different etch‐pits of 〈001〉‐oriented and misoriented crystals and their evolution with etching time in order to get a better understanding of defect density and formation during CVD growth.
- 1 September 2011
- Published by Gemological Institute of America in Gems & Gemology
- Vol. 47 (3) , 202-207
Exploring the Origin and Nature of Luminescent Regions in CVD Synthetic Diamond
- 1 September 2011
- Published by Gemological Institute of America in Gems & Gemology
- Vol. 47 (3) , 202-207
Exploring the Origin and Nature of Luminescent Regions in CVD Synthetic Diamond
- 9 August 2011
- Published by Wiley in Physica Status Solidi (a)
- Vol. 208 (9) , 2028-2032
Effect of argon addition on the growth of thick single crystal diamond by high‐power plasma CVD
Diamond films were synthesized with up to 50% argon in the gas phase using high power plasma‐assisted chemical vapour deposition (PACVD). This resulted in a strong increase of the deposition rates. Polycrystalline diamond (PCD) films grown with Ar have shown a higher incorporation of sp2 phases but with no dramatic change in crystal morphologies. Thick single crystal diamond films did not show any obvious change in crystal quality though. By using optical emission spectroscopy (OES) and plasma simulation, it was found that the gas temperature is increased by the addition of argon by at least 500 K. This in turn promotes dissociation of H2 into H‐atom as would be obtained from an increase of the plasma power density. High‐power PACVD with argon addition is thus an efficient technique for the fast growth of thick single crystal films without the cost and additional problems related to an increase of the injected microwave power.
- 9 August 2011
- Published by Wiley in Physica Status Solidi (a)
- Vol. 208 (9) , 2028-2032
Effect of argon addition on the growth of thick single crystal diamond by high‐power plasma CVD
Diamond films were synthesized with up to 50% argon in the gas phase using high power plasma‐assisted chemical vapour deposition (PACVD). This resulted in a strong increase of the deposition rates. Polycrystalline diamond (PCD) films grown with Ar have shown a higher incorporation of sp2 phases but with no dramatic change in crystal morphologies. Thick single crystal diamond films did not show any obvious change in crystal quality though. By using optical emission spectroscopy (OES) and plasma simulation, it was found that the gas temperature is increased by the addition of argon by at least 500 K. This in turn promotes dissociation of H2 into H‐atom as would be obtained from an increase of the plasma power density. High‐power PACVD with argon addition is thus an efficient technique for the fast growth of thick single crystal films without the cost and additional problems related to an increase of the injected microwave power.