O. Alvarez-Fregoso
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
O. Alvarez-Fregoso has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Ciro Falcony
Department of Physics, CINVESTAV-IPN, Mexico D.F., Mexico
6 shared publications E. Martínez
Instituto de Investigaciones en Materiales., UNAM, A.P. 70‐360 Coyoacán 04510 México
3 shared publicationsC. Falcony
IPN, México
2 shared publicationsF. Ramos‐Brito
Laboratorio de Materiales Optoelectrónicos, DIDe, Centro de Ciencias de Sinaloa, Av. De las Américas No. 2771 Nte. Col. Villa Universidad, Culiacán, Sinaloa, 80010 México, C.P., Mexico
2 shared publicationsJ. A. Juarez-Islas
Instituto de Investigaciones en Materiales-UNAM, Circuito Exterior S/N, Cd. Universitaria Mexico, D. F., 04510, MÉXICO
2 shared publicationsJ. Guzmán-Mendoza
Instituto de Investigaciones en Materiales, Universidad Nacional Autónoma de México , A.P. 70-360, Coyoacán 04510, México, D.F., Mexico
2 shared publications
Latest Publications
- 8 February 2010
- Published by Wiley in Physica Status Solidi (a)
- Vol. 207 (2) , 417-422
Luminescent characteristics of praseodymium‐doped zinc aluminate powders
In this research, we report the cathodoluminescence (CL) and preliminary photoluminescence (PL) properties of praseodymium‐doped zinc aluminate powders. ZnAl2O4:Pr powders were synthesized by a very simple chemical process. X‐ray diffraction spectra indicated a cubic spinel crystalline structure with an average crystallite size of 15 nm. CL properties of the powders were studied as a function of the praseodymium concentration and electron‐accelerating potential. In this case, all the cathodoluminescent emission spectra showed main peaks located at 494, 535, 611, 646, and 733 nm, which were associated to the electronic transitions 3P0 → 3H4, 3P0 → 3H5, 3P0 → 3H6, 3P0 → 3F2, and 3P0 → 3F4 of the Pr3+ ions, respectively. A quenching of the CL, with increasing doping concentration, was observed. Also, an increment on cathodoluminescent emission intensity was observed as the accelerating voltage increased. The PL emission spectrum showed similar characteristics to those of the CL spectra. The chemical composition of the powders, as determined by energy dispersive spectroscopy, is also reported. In addition, the surface morphology characteristics of the powders are shown.
- 8 February 2010
- Published by Wiley in Physica Status Solidi (a)
- Vol. 207 (2) , 417-422
Luminescent characteristics of praseodymium‐doped zinc aluminate powders
In this research, we report the cathodoluminescence (CL) and preliminary photoluminescence (PL) properties of praseodymium‐doped zinc aluminate powders. ZnAl2O4:Pr powders were synthesized by a very simple chemical process. X‐ray diffraction spectra indicated a cubic spinel crystalline structure with an average crystallite size of 15 nm. CL properties of the powders were studied as a function of the praseodymium concentration and electron‐accelerating potential. In this case, all the cathodoluminescent emission spectra showed main peaks located at 494, 535, 611, 646, and 733 nm, which were associated to the electronic transitions 3P0 → 3H4, 3P0 → 3H5, 3P0 → 3H6, 3P0 → 3F2, and 3P0 → 3F4 of the Pr3+ ions, respectively. A quenching of the CL, with increasing doping concentration, was observed. Also, an increment on cathodoluminescent emission intensity was observed as the accelerating voltage increased. The PL emission spectrum showed similar characteristics to those of the CL spectra. The chemical composition of the powders, as determined by energy dispersive spectroscopy, is also reported. In addition, the surface morphology characteristics of the powders are shown.
- 1 March 2008
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 13 (1) , 130-135
Caracterización eléctrica de películas delgadas de Al2O3 depositadas sobre GaAs por la técnica de rocío pirolítico
Se estudiaron las características eléctricas de películas delgadas de óxido de aluminio preparadas por la técnica de rocío pirolítico ultrasónico. Las películas delgadas se depositaron a partir de una solución de acetilacetonato de aluminio en N,N-dimetilformamida sobre substratos monocristalinos de GaAs (100) tipo-p. La temperatura de depósito fue de 300 a 600 ºC. Las propiedades eléctricas de las películas en función de la temperatura de substrato se determinaron por medidas de capacitancia y corriente contra voltaje mediante la incorporación de las películas en estructuras tipo MOS (metal-óxido-semiconductor). La densidad de estados de interfaz resultó del orden de 10(12) 1/eV-cm² y el dispositivo MOS soportó campos eléctricos mayores a 5MV/cm, sin mostrar rompimiento dieléctrico. El índice de refracción se determinó por elipsometría a 633nm, con un valor máximo del orden de 1.64.
- 1 March 2008
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 13 (1) , 130-135
Caracterización eléctrica de películas delgadas de Al2O3 depositadas sobre GaAs por la técnica de rocío pirolítico
Se estudiaron las características eléctricas de películas delgadas de óxido de aluminio preparadas por la técnica de rocío pirolítico ultrasónico. Las películas delgadas se depositaron a partir de una solución de acetilacetonato de aluminio en N,N-dimetilformamida sobre substratos monocristalinos de GaAs (100) tipo-p. La temperatura de depósito fue de 300 a 600 ºC. Las propiedades eléctricas de las películas en función de la temperatura de substrato se determinaron por medidas de capacitancia y corriente contra voltaje mediante la incorporación de las películas en estructuras tipo MOS (metal-óxido-semiconductor). La densidad de estados de interfaz resultó del orden de 10(12) 1/eV-cm² y el dispositivo MOS soportó campos eléctricos mayores a 5MV/cm, sin mostrar rompimiento dieléctrico. El índice de refracción se determinó por elipsometría a 633nm, con un valor máximo del orden de 1.64.
- 1 October 2007
- Published by Taylor & Francis in Radiation Effects and Defects in Solids
- Vol. 162 (10-11) , 723-729
Photoluminescent characteristics of hafnium oxide layers activated with trivalent terbium (HfO2:Tb+3)
Hafnium oxide layers doped with trivalent terbium ions have been synthesized using the ultrasonic spray pyrolysis technique. Photoluminescence properties were studied as a function of growth parameters such as the substrate temperature and the terbium concentration. The films were grown starting from aqueous solution of Hafnium and Terbium chlorides. The results show that crystalline structure of HfO2:Tb+3 films depends on the temperature. Emission and excitation spectra were obtained for the HfO2:Tb+3 films using 262 nm as the excitation wavelength. All emission spectra show bands centered at 488, 542, 584 and 621 nm, which correspond to the electronic transitions: 5D4→7Fj (j=3, …, 6) characteristic of trivalent terbium ion. The dominant emission intensity corresponds to the green color, which depend on the terbium concentration incorporated inside the host matrix.
- 1 October 2007
- Published by Taylor & Francis in Radiation Effects and Defects in Solids
- Vol. 162 (10-11) , 723-729
Photoluminescent characteristics of hafnium oxide layers activated with trivalent terbium (HfO2:Tb+3)
Hafnium oxide layers doped with trivalent terbium ions have been synthesized using the ultrasonic spray pyrolysis technique. Photoluminescence properties were studied as a function of growth parameters such as the substrate temperature and the terbium concentration. The films were grown starting from aqueous solution of Hafnium and Terbium chlorides. The results show that crystalline structure of HfO2:Tb+3 films depends on the temperature. Emission and excitation spectra were obtained for the HfO2:Tb+3 films using 262 nm as the excitation wavelength. All emission spectra show bands centered at 488, 542, 584 and 621 nm, which correspond to the electronic transitions: 5D4→7Fj (j=3, …, 6) characteristic of trivalent terbium ion. The dominant emission intensity corresponds to the green color, which depend on the terbium concentration incorporated inside the host matrix.
- 28 June 2007
- Published by Wiley in Physica Status Solidi (a)
- Vol. 204 (7) , 2355-2361
Violet–blue luminescence from hafnium oxide layers doped with CeCl3 prepared by the spray pyrolysis process
HfO2:CeCl3 coatings were deposited by the spray pyrolysis method employing hafnium dichloride oxide and CeCl3 dissolved in deionized water (18 MΩ/cm). The room temperature photoluminescence characteristics of the HfO2:CeCl3 films were studied as a function of the deposition parameters such as doping concentrations and substrate temperature. The presence of two different Ce3+ centres in HfO2 is detected from photoluminescence measurements. A reduction of the luminescence intensity is observed with an increase of both the CeCl3 concentration and the deposition temperature. X‐ray diffraction measurements of these films showed that the crystalline structure depends on the substrate temperature. For substrate temperatures less than 350 °C the deposited films are almost amorphous, while substrate temperatures higher than 400 °C produce diffraction peaks corresponding to the monoclinic phase of HfO2. The chemical composition of the films as determined by energy dispersive spectroscopy is also reported. Furthermore, the surface morphology characteristics of the coatings, as a function of the deposition temperature, are also presented.
- 28 June 2007
- Published by Wiley in Physica Status Solidi (a)
- Vol. 204 (7) , 2355-2361
Violet–blue luminescence from hafnium oxide layers doped with CeCl3 prepared by the spray pyrolysis process
HfO2:CeCl3 coatings were deposited by the spray pyrolysis method employing hafnium dichloride oxide and CeCl3 dissolved in deionized water (18 MΩ/cm). The room temperature photoluminescence characteristics of the HfO2:CeCl3 films were studied as a function of the deposition parameters such as doping concentrations and substrate temperature. The presence of two different Ce3+ centres in HfO2 is detected from photoluminescence measurements. A reduction of the luminescence intensity is observed with an increase of both the CeCl3 concentration and the deposition temperature. X‐ray diffraction measurements of these films showed that the crystalline structure depends on the substrate temperature. For substrate temperatures less than 350 °C the deposited films are almost amorphous, while substrate temperatures higher than 400 °C produce diffraction peaks corresponding to the monoclinic phase of HfO2. The chemical composition of the films as determined by energy dispersive spectroscopy is also reported. Furthermore, the surface morphology characteristics of the coatings, as a function of the deposition temperature, are also presented.
- 9 December 2004
- Published by Wiley in Physica Status Solidi (a)
- Vol. 202 (1) , 102-107
Cathodoluminescent characteristics of Sm‐doped ZnAl2O4 nanostructured powders
Cathodoluminescent (CL) powders of zinc aluminate activated with samarium ions have been prepared by a co‐precipitation chemical process. Different doping concentrations in the start mixture and sintering temperatures for the precipitated powder were studied. It was observed that the crystalline characteristics of the powders depend upon the sintering temperature. For temperatures higher than 450 °C, the powders presented the cubic spinel phase with a lattice parameter value of 8.0756 Å, and grain sizes from 50 to 100 nm with semispherical shape. The CL emission spectra showed broad bands localized at 564, 602, 644, and 703 nm associated with 4G5/2 → 6H5/2, 4G5/2 → 6H7/2, 4G5/2 → 6H9/2, and 4G5/2 → 6H11/2 transitions in the Sm3+ ions, respectively. Concentration quenching of the cathodoluminescence occurred at about 4.26 at% of the activator (Sm) concentration inside the sintered powders.
- 9 December 2004
- Published by Wiley in Physica Status Solidi (a)
- Vol. 202 (1) , 102-107
Cathodoluminescent characteristics of Sm‐doped ZnAl2O4 nanostructured powders
Cathodoluminescent (CL) powders of zinc aluminate activated with samarium ions have been prepared by a co‐precipitation chemical process. Different doping concentrations in the start mixture and sintering temperatures for the precipitated powder were studied. It was observed that the crystalline characteristics of the powders depend upon the sintering temperature. For temperatures higher than 450 °C, the powders presented the cubic spinel phase with a lattice parameter value of 8.0756 Å, and grain sizes from 50 to 100 nm with semispherical shape. The CL emission spectra showed broad bands localized at 564, 602, 644, and 703 nm associated with 4G5/2 → 6H5/2, 4G5/2 → 6H7/2, 4G5/2 → 6H9/2, and 4G5/2 → 6H11/2 transitions in the Sm3+ ions, respectively. Concentration quenching of the cathodoluminescence occurred at about 4.26 at% of the activator (Sm) concentration inside the sintered powders.
- 15 January 2004
- Published by Wiley in Physica Status Solidi (a)
- Vol. 201 (1) , 72-79
Characterization of ZnAl2O4: Tb luminescent films deposited by ultrasonic spray pyrolysis technique
- 15 January 2004
- Published by Wiley in Physica Status Solidi (a)
- Vol. 201 (1) , 72-79
Characterization of ZnAl2O4: Tb luminescent films deposited by ultrasonic spray pyrolysis technique
- 1 September 2002
- Published by Elsevier in Optical Materials
- Vol. 20 (2) , 113-118
Characterization of ZrO2:Mn, Cl luminescent coatings synthesized by the Pyrosol technique
- 1 September 2002
- Published by Elsevier in Optical Materials
- Vol. 20 (2) , 113-118
Characterization of ZrO2:Mn, Cl luminescent coatings synthesized by the Pyrosol technique
- 15 October 2001
- Published by AIP Publishing in Applied Physics Letters
- Vol. 79 (16) , 2555-2557
Morphological, optical, and photoluminescent characteristics of GaAs1−xNx nanowhiskered thin films
GaAs 1−x N x solid-solution thin films of nanometric size were prepared on glass substrates by the radio-frequency sputtering technique. Atomic-force microscopy images show that the films are composed of grains with a whisker shape, whose size is practically independent of the substrate temperature. Their typical diameters range between 40 and 45 Å. The surface morphology exhibits a high density of whisker-like features that are almost normal to the substrate plane. This density increases as the substrate temperature increases, but, in essence, the nanowhisker diameter does not. Optical absorption spectra of the samples show a band-gap energy blueshift as large as 1.5 eV with respect to that of the GaAs bulk value, which was associated with strong quantum-confinement effects. Photoluminescence emission spectra in the blue range of 428–438 nm confirm the quantum-size effects in the GaAs1−xNx nanowhiskered thin films.
- 15 October 2001
- Published by AIP Publishing in Applied Physics Letters
- Vol. 79 (16) , 2555-2557
Morphological, optical, and photoluminescent characteristics of GaAs1−xNx nanowhiskered thin films
GaAs 1−x N x solid-solution thin films of nanometric size were prepared on glass substrates by the radio-frequency sputtering technique. Atomic-force microscopy images show that the films are composed of grains with a whisker shape, whose size is practically independent of the substrate temperature. Their typical diameters range between 40 and 45 Å. The surface morphology exhibits a high density of whisker-like features that are almost normal to the substrate plane. This density increases as the substrate temperature increases, but, in essence, the nanowhisker diameter does not. Optical absorption spectra of the samples show a band-gap energy blueshift as large as 1.5 eV with respect to that of the GaAs bulk value, which was associated with strong quantum-confinement effects. Photoluminescence emission spectra in the blue range of 428–438 nm confirm the quantum-size effects in the GaAs1−xNx nanowhiskered thin films.
- 10 July 2000
- Published by Wiley in Physica Status Solidi (b)
- Vol. 220 (1) , 575-582
Cu/Mo Nanostructured Alloy Thin Films
- 10 July 2000
- Published by Wiley in Physica Status Solidi (b)
- Vol. 220 (1) , 575-582
Cu/Mo Nanostructured Alloy Thin Films
- 1 July 2000
- Published by Wiley in Physica Status Solidi (b)
- Vol. 220 (1) , 677-681
Characterization of Al2O3:Eu3+ Luminescent Coatings Prepared by Spray Pyrolysis Technique
- 1 July 2000
- Published by Wiley in Physica Status Solidi (b)
- Vol. 220 (1) , 677-681
Characterization of Al2O3:Eu3+ Luminescent Coatings Prepared by Spray Pyrolysis Technique