Bengt Wesslén
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bengt Wesslén has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Nadia Ljungberg
Department of Polymer Science and Engineering, Lund Institute of Technology, Lund, Sweden
3 shared publicationsJörgen Rassing
Department of Chemical Engineering II, Lund Institute of Technology, Center for Chemistry and Chemical Engineering, P.O. Box 124, S-221 00 Lund, Sweden
2 shared publications- Ola J. Karlsson
Saint-Gobain Ecophon AB, Yttervägen 1, 265 75 Hyllinge, Sweden
2 shared publications Åsa Halldén
Department of Polymer Science and Engineering, Lund University, P.O. Box 124, SE‐221 00 Lund, Sweden
2 shared publicationsBertil Ohlsson
Perstorp Compound, SE‐284 80 Perstorp, Sweden
1 shared publicationChristina Freij-Larsson
Lund Institute of Technology, Chemical Center, Department of Chemical Engineering II, Box 124, S-221 00 Lund, Sweden
1 shared publication
Latest Publications
- 1 March 2005
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 96 (4) , 992-1002
Plasticization of poly(lactic acid) with oligomeric malonate esteramides: Dynamic mechanical and thermal film properties
Two oligomeric malonate esteramides and an oligomeric malonate ester were synthesized with the intention to plasticize poly(lactic acid), PLA. The synthesis was performed by reacting diethyl bishydroxymethyl malonate (DBM) with adipoyl dichloride and one of two diamines, that is, triethylene glycol diamine (TA) and polyoxypropylene glycol diamine (PA), or triethylene glycol (TEG), giving three platicizing agents denoted as DBMATA, DBMAPA, and DBMAT, respectively. The synthesis products were characterized by size exclusion chromatography and Fourier transform infrared spectroscopy, and blended with PLA at a concentration of 15 wt %. Dynamic mechanical analysis, differential scanning calorimetry, and tensile testing were used to investigate the physical properties of films from the resulting blends. All three plasticizers decreased the glass transition temperature of PLA, and the largest decrement was observed for PLA/DBMATA. Films of DBMATA and DBMAT showed enhanced flexibility in strain at break as compared to neat PLA. Subsequently, it was found that thermal annealing of the plasticized materials (4 h at 100°C) encouraged cold crystallization, inducing phase separation in the blends, and caused them to regain the brittleness of neat PLA. On the other hand, by aging (6 weeks) the blends at ambient conditions, cold crystallization could be avoided and the flexibility in the films maintained. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 992–1002, 2005
- 1 March 2005
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 96 (4) , 992-1002
Plasticization of poly(lactic acid) with oligomeric malonate esteramides: Dynamic mechanical and thermal film properties
Two oligomeric malonate esteramides and an oligomeric malonate ester were synthesized with the intention to plasticize poly(lactic acid), PLA. The synthesis was performed by reacting diethyl bishydroxymethyl malonate (DBM) with adipoyl dichloride and one of two diamines, that is, triethylene glycol diamine (TA) and polyoxypropylene glycol diamine (PA), or triethylene glycol (TEG), giving three platicizing agents denoted as DBMATA, DBMAPA, and DBMAT, respectively. The synthesis products were characterized by size exclusion chromatography and Fourier transform infrared spectroscopy, and blended with PLA at a concentration of 15 wt %. Dynamic mechanical analysis, differential scanning calorimetry, and tensile testing were used to investigate the physical properties of films from the resulting blends. All three plasticizers decreased the glass transition temperature of PLA, and the largest decrement was observed for PLA/DBMATA. Films of DBMATA and DBMAT showed enhanced flexibility in strain at break as compared to neat PLA. Subsequently, it was found that thermal annealing of the plasticized materials (4 h at 100°C) encouraged cold crystallization, inducing phase separation in the blends, and caused them to regain the brittleness of neat PLA. On the other hand, by aging (6 weeks) the blends at ambient conditions, cold crystallization could be avoided and the flexibility in the films maintained. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 992–1002, 2005
- 1 December 2004
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 95 (3) , 583-595
Degradation of low density polyethylene during extrusion. IV. Off-flavor compounds in extruded films of stabilized LDPE
- 1 December 2004
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 95 (3) , 583-595
Degradation of low density polyethylene during extrusion. IV. Off-flavor compounds in extruded films of stabilized LDPE
- 1 October 2004
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 94 (5) , 2140-2149
Thermomechanical film properties and aging of blends of poly(lactic acid) and malonate oligomers
Malonate oligomers were synthesized as plasticizers for poly(lactic acid) (PLA). Esterification reactions were performed between diethyl bishydroxymethyl malonate (DBM) and either adipoyl dichloride or succinyl dichloride. Two molar masses were obtained within each series. Blending was carried out with PLA and the four oligomers as well as the monomeric unit from the syntheses (DBM). Dynamic mechanical analysis and differential scanning calorimetry were used to investigate the viscoelastic mechanical and thermal film properties of the blends. All the investigated plasticizers reduced the glass‐transition temperature of PLA, and the plasticization effect was better for the plasticizers of low molar mass. However, the amorphous domains of PLA became saturated with plasticizer at a certain concentration, and phase separation occurred. A higher molar mass of the plasticizer caused this saturation to occur at lower plasticizer concentrations. Subsequently, the aging of the blends at the ambient temperature for 4 months induced phase separation in the blends containing DBM, whereas those with an oligomeric plasticizer were stable and remained compatible with PLA within the aging period. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2140–2149, 2004
- 1 October 2004
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 94 (5) , 2140-2149
Thermomechanical film properties and aging of blends of poly(lactic acid) and malonate oligomers
Malonate oligomers were synthesized as plasticizers for poly(lactic acid) (PLA). Esterification reactions were performed between diethyl bishydroxymethyl malonate (DBM) and either adipoyl dichloride or succinyl dichloride. Two molar masses were obtained within each series. Blending was carried out with PLA and the four oligomers as well as the monomeric unit from the syntheses (DBM). Dynamic mechanical analysis and differential scanning calorimetry were used to investigate the viscoelastic mechanical and thermal film properties of the blends. All the investigated plasticizers reduced the glass‐transition temperature of PLA, and the plasticization effect was better for the plasticizers of low molar mass. However, the amorphous domains of PLA became saturated with plasticizer at a certain concentration, and phase separation occurred. A higher molar mass of the plasticizer caused this saturation to occur at lower plasticizer concentrations. Subsequently, the aging of the blends at the ambient temperature for 4 months induced phase separation in the blends containing DBM, whereas those with an oligomeric plasticizer were stable and remained compatible with PLA within the aging period. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2140–2149, 2004
- 17 April 2003
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 88 (14) , 3239-3247
Film extrusion and film weldability of poly(lactic acid) plasticized with triacetine and tributyl citrate
Film extrusion and welding of biodegradable polymer films are important processes that must be considered in the development of compostable packaging materials. Film extrusion of poly(lactic acid) (PLA) has proved to be rather difficult because of its brittleness, but the flexibility of PLA can be improved by incorporation of a plasticizer in the material. PLA was plasticized with triacetine (TAc) and tributyl citrate (TbC). The blended materials and neat PLA were film extruded and the films were welded with constant heat (CH) welding. The films were analyzed by means of gas chromatography (GC), dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), gel permeation chromatography (GPC), contact angle measurements, and tensile testing. Storage of the plasticized films resulted in an increased crystallinity and changes in the film properties, rendering CH welding difficult. The welding process had no influence on thermal properties, such as cold crystallization temperature, melting temperature, crystallization temperature, and degree of crystallinity, of neat PLA but caused significant changes in the crystallinity of the plasticized materials. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3239–3247, 2003
- 17 April 2003
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 88 (14) , 3239-3247
Film extrusion and film weldability of poly(lactic acid) plasticized with triacetine and tributyl citrate
Film extrusion and welding of biodegradable polymer films are important processes that must be considered in the development of compostable packaging materials. Film extrusion of poly(lactic acid) (PLA) has proved to be rather difficult because of its brittleness, but the flexibility of PLA can be improved by incorporation of a plasticizer in the material. PLA was plasticized with triacetine (TAc) and tributyl citrate (TbC). The blended materials and neat PLA were film extruded and the films were welded with constant heat (CH) welding. The films were analyzed by means of gas chromatography (GC), dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), gel permeation chromatography (GPC), contact angle measurements, and tensile testing. Storage of the plasticized films resulted in an increased crystallinity and changes in the film properties, rendering CH welding difficult. The welding process had no influence on thermal properties, such as cold crystallization temperature, melting temperature, crystallization temperature, and degree of crystallinity, of neat PLA but caused significant changes in the crystallinity of the plasticized materials. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3239–3247, 2003
- 21 August 2002
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 86 (5) , 1227-1234
The effects of plasticizers on the dynamic mechanical and thermal properties of poly(lactic acid)
Poly(lactic acid) (PLA) was blended with five plasticizers in a batchwise mixer and pressed into films. The films were analyzed by means of dynamic mechanical analysis and differential scanning calorimetry to investigate the properties of the blends. Triacetine and tributyl citrate proved to be effective as plasticizers when blended with PLA. The glass transition temperature of PLA decreased linearly as the plasticizer content was increased. Both plasticizers were miscible with PLA to an extent of ∼ 25 wt %. At this point, the PLA seemed to be saturated with plasticizer and the blends tended to phase separate when more plasticizer was added. There were also signs of phase separation occurring in samples heated at 35, 50, and 80°C, most likely because of the material undergoing crystallization. The presence of the plasticizers induced an increased crystallinity by enhancing the molecular mobility. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1227–1234, 2002
- 21 August 2002
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 86 (5) , 1227-1234
The effects of plasticizers on the dynamic mechanical and thermal properties of poly(lactic acid)
Poly(lactic acid) (PLA) was blended with five plasticizers in a batchwise mixer and pressed into films. The films were analyzed by means of dynamic mechanical analysis and differential scanning calorimetry to investigate the properties of the blends. Triacetine and tributyl citrate proved to be effective as plasticizers when blended with PLA. The glass transition temperature of PLA decreased linearly as the plasticizer content was increased. Both plasticizers were miscible with PLA to an extent of ∼ 25 wt %. At this point, the PLA seemed to be saturated with plasticizer and the blends tended to phase separate when more plasticizer was added. There were also signs of phase separation occurring in samples heated at 35, 50, and 80°C, most likely because of the material undergoing crystallization. The presence of the plasticizers induced an increased crystallinity by enhancing the molecular mobility. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1227–1234, 2002
- 23 October 2000
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 78 (13) , 2416-2424
Poly(ethylene-graft-ethylene oxide) (PE-PEO) and poly(ethylene-co-acrylic acid) (PEAA) as compatibilizers in blends of LDPE and polyamide-6
- 23 October 2000
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 78 (13) , 2416-2424
Poly(ethylene-graft-ethylene oxide) (PE-PEO) and poly(ethylene-co-acrylic acid) (PEAA) as compatibilizers in blends of LDPE and polyamide-6
- 24 May 2000
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 77 (2) , 297-311
Influence of seed polymer molecular weight on polymerization kinetics and particle morphology of structured styrene–butadiene latexes
- 24 May 2000
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 77 (2) , 297-311
Influence of seed polymer molecular weight on polymerization kinetics and particle morphology of structured styrene–butadiene latexes
- 2 December 1999
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 75 (2) , 316-326
Surface modification of LDPE with PE-PEO graft copolymer
- 2 December 1999
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 75 (2) , 316-326
Surface modification of LDPE with PE-PEO graft copolymer
- 5 December 1998
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 70 (10) , 2041-2051
Swelling of poly(styrene-co-methacrylic acid) latex by isoprene
- 5 December 1998
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 70 (10) , 2041-2051
Swelling of poly(styrene-co-methacrylic acid) latex by isoprene
- 31 October 1998
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 70 (5) , 897-906
Influence of spacer groups on grafting ability, curing ability, and film properties of water-based radiation curable latexes
- 31 October 1998
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 70 (5) , 897-906
Influence of spacer groups on grafting ability, curing ability, and film properties of water-based radiation curable latexes