Patrik Schmuki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Patrik Schmuki has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
Indhumati Paramasivam
Department of Materials Science WW4, LKO, University of Erlangen-Nürnberg, Martensstr.7, 91058 Erlangen, Germany
4 shared publications- Jan M. Macak
University of Pardubice
4 shared publications - Kiyoung Lee
Department of Chemistry and Chemical Engineering, Inha University, Incheon, Republic of Korea
3 shared publications A. Ghicov
Department of Materials Science and Engineering, WW4‐LKO, University of Erlangen‐Nuremberg, Martensstraße 7, 91058 Erlangen, Germany
2 shared publicationsD. Kim
Department of Materials Science and Engineering, WW4‐LKO, University of Erlangen‐Nuremberg, Martensstraße 7, 91058 Erlangen, Germany
2 shared publicationsD. Tsoukleris
Institute of Physical Chemistry, NCSR “Demokritos”, 15310 Aghia Paraskevi Attikis, Athens, Greece
2 shared publications
Latest Publications
- 1 November 2016
- Published by Elsevier in Electrochemistry Communications
- Vol. 72, 27-31
Tantalum nitride nanotube photoanodes: Establishing a beneficial back-contact by lift-off and transfer to titanium nitride layer
- 1 November 2016
- Published by Elsevier in Electrochemistry Communications
- Vol. 72, 27-31
Tantalum nitride nanotube photoanodes: Establishing a beneficial back-contact by lift-off and transfer to titanium nitride layer
- 25 February 2015
- Published by Wiley in ChemElectroChem
- Vol. 2 (6) , 824-828
Use of Anodic TiO2 Nanotube Layers as Mesoporous Scaffolds for Fabricating CH3NH3PbI3 Perovskite‐Based Solid‐State Solar Cells
We optimize the deposition of CH3NH3PbI3 perovskite into mesoporous electrodes consisting of anodic TiO2 nanotube layers. By a simple spin‐coating approach, complete filling of the tube scaffolds is obtained, which leads to interdigitated perovskite structures in conformal contact with the TiO2 tube counterparts. Such assemblies can be used as solid‐state solar cells in a hole‐transporting‐material‐free configuration, that is, the tube scaffold serves as electron collector and blocking layer, while the perovskite acts as visible‐light absorber and hole‐transporting material. We show that the complete filling of the tube scaffold with the perovskite is essential to improve the solar cell efficiency.
- 25 February 2015
- Published by Wiley in ChemElectroChem
- Vol. 2 (6) , 824-828
Use of Anodic TiO2 Nanotube Layers as Mesoporous Scaffolds for Fabricating CH3NH3PbI3 Perovskite‐Based Solid‐State Solar Cells
We optimize the deposition of CH3NH3PbI3 perovskite into mesoporous electrodes consisting of anodic TiO2 nanotube layers. By a simple spin‐coating approach, complete filling of the tube scaffolds is obtained, which leads to interdigitated perovskite structures in conformal contact with the TiO2 tube counterparts. Such assemblies can be used as solid‐state solar cells in a hole‐transporting‐material‐free configuration, that is, the tube scaffold serves as electron collector and blocking layer, while the perovskite acts as visible‐light absorber and hole‐transporting material. We show that the complete filling of the tube scaffold with the perovskite is essential to improve the solar cell efficiency.
- 18 June 2014
- Published by Wiley in ChemElectroChem
- Vol. 1 (7) , 1133-1137
Controlled Thermal Annealing Tunes the Photoelectrochemical Properties of Nanochanneled Tin‐Oxide Structures
We study the effect of thermal annealing conditions (up to 400 °C) and atmospheres (air, Arand O2) on a newly developed nanochannel tin‐oxide structure. The nanochanneled structures were prepared by self‐organized anodization of metallic tin. Thermal annealing conditions have a strong impact on the crystallinity and content of Sn2+ defects present in the structure, and thus have a strong influence on the photoresponse characteristics of the films. Photocurrent measurements show that films annealed at 200 °C in Ar atmosphere exhibit a band gap as low as 2.4 eV and a photoresponse in the visible range. This effect is ascribed to a large content of Sn2+ defects in the structure and the improved crystallinity of the films annealed at this temperature. On the contrary, the Sn2+ content is decreased when annealing at 400 °C under aerobic conditions, which correlates with a shift in the film band gap to 3.2 eV, closer to the reported value for pure SnO2 (3.6 eV).
- 18 June 2014
- Published by Wiley in ChemElectroChem
- Vol. 1 (7) , 1133-1137
Controlled Thermal Annealing Tunes the Photoelectrochemical Properties of Nanochanneled Tin‐Oxide Structures
We study the effect of thermal annealing conditions (up to 400 °C) and atmospheres (air, Arand O2) on a newly developed nanochannel tin‐oxide structure. The nanochanneled structures were prepared by self‐organized anodization of metallic tin. Thermal annealing conditions have a strong impact on the crystallinity and content of Sn2+ defects present in the structure, and thus have a strong influence on the photoresponse characteristics of the films. Photocurrent measurements show that films annealed at 200 °C in Ar atmosphere exhibit a band gap as low as 2.4 eV and a photoresponse in the visible range. This effect is ascribed to a large content of Sn2+ defects in the structure and the improved crystallinity of the films annealed at this temperature. On the contrary, the Sn2+ content is decreased when annealing at 400 °C under aerobic conditions, which correlates with a shift in the film band gap to 3.2 eV, closer to the reported value for pure SnO2 (3.6 eV).
- 13 February 2014
- Published by Wiley in ChemSusChem
- Vol. 7 (3) , 934-940
Anodic Nanotubular/porous Hematite Photoanode for Solar Water Splitting: Substantial Effect of Iron Substrate Purity
Anodization of iron substrates is one of the most simple and effective ways to fabricate nanotubular (and porous) structures that could be directly used as a photoanode for solar water splitting. Up to now, all studies in this field focused on achieving a better geometry of the hematite nanostructures for a higher efficiency. The present study, however, highlights that the purity of the iron substrate used for any anodic‐hematite‐formation approach is extremely important in view of the water‐splitting performance. Herein, anodic self‐organized oxide morphologies (nanotubular and nanoporous) are grown on different iron substrates under a range of anodization conditions, including elevated temperatures and anodization supported by ultrasonication. Substrate purity has not only a significant effect on oxide‐layer growth rate and tube morphology, but also gives rise to a ninefold increase in the photoelectrochemical water‐splitting performance (0.250 vs. 0.028 mA cm−2 at 1.40 V vs. reversible hydrogen electrode under AM 1.5 100 mW cm−2 illumination) for 99.99 % versus 99.5 % purity iron substrates of similar oxide geometry. Elemental analysis and model alloys show that particularly manganese impurities have a strong detrimental effect on the water‐splitting performance.
- 13 February 2014
- Published by Wiley in ChemSusChem
- Vol. 7 (3) , 934-940
Anodic Nanotubular/porous Hematite Photoanode for Solar Water Splitting: Substantial Effect of Iron Substrate Purity
Anodization of iron substrates is one of the most simple and effective ways to fabricate nanotubular (and porous) structures that could be directly used as a photoanode for solar water splitting. Up to now, all studies in this field focused on achieving a better geometry of the hematite nanostructures for a higher efficiency. The present study, however, highlights that the purity of the iron substrate used for any anodic‐hematite‐formation approach is extremely important in view of the water‐splitting performance. Herein, anodic self‐organized oxide morphologies (nanotubular and nanoporous) are grown on different iron substrates under a range of anodization conditions, including elevated temperatures and anodization supported by ultrasonication. Substrate purity has not only a significant effect on oxide‐layer growth rate and tube morphology, but also gives rise to a ninefold increase in the photoelectrochemical water‐splitting performance (0.250 vs. 0.028 mA cm−2 at 1.40 V vs. reversible hydrogen electrode under AM 1.5 100 mW cm−2 illumination) for 99.99 % versus 99.5 % purity iron substrates of similar oxide geometry. Elemental analysis and model alloys show that particularly manganese impurities have a strong detrimental effect on the water‐splitting performance.
- 25 September 2013
- Published by Wiley in Chemistry – A European Journal
- Vol. 19 (46) , 15530-15534
Nickel Hydroxide Nanoparticle Activated Semi‐metallic TiO2 Nanotube Arrays for Non‐enzymatic Glucose Sensing
Semi‐metallic TiO2 nanotube arrays (TiOxCy NTs) have been decorated uniformly with Ni(OH)2 nanoparticles without the aid of a polymer binder. The resulting hybrid nanotube arrays exhibit excellent catalytic activity towards non‐enzymatic glucose electro‐oxidation. The anodic current density of the glucose oxidation is significantly improved compared with traditional TiO2 nanotubes decorated with Ni(OH)2. Moreover, the Ni(OH)2/TiOxCy NT‐based electrode shows a fast response, high sensitivity, wide linear range, good selectivity and stability towards glucose electro‐oxidation, and thus provides a promising and cost‐effective sensing platform for non‐enzymatic glucose detection.
- 25 September 2013
- Published by Wiley in Chemistry – A European Journal
- Vol. 19 (46) , 15530-15534
Nickel Hydroxide Nanoparticle Activated Semi‐metallic TiO2 Nanotube Arrays for Non‐enzymatic Glucose Sensing
Semi‐metallic TiO2 nanotube arrays (TiOxCy NTs) have been decorated uniformly with Ni(OH)2 nanoparticles without the aid of a polymer binder. The resulting hybrid nanotube arrays exhibit excellent catalytic activity towards non‐enzymatic glucose electro‐oxidation. The anodic current density of the glucose oxidation is significantly improved compared with traditional TiO2 nanotubes decorated with Ni(OH)2. Moreover, the Ni(OH)2/TiOxCy NT‐based electrode shows a fast response, high sensitivity, wide linear range, good selectivity and stability towards glucose electro‐oxidation, and thus provides a promising and cost‐effective sensing platform for non‐enzymatic glucose detection.
- 2 July 2013
- Published by Wiley in Angewandte Chemie International Edition
- Vol. 52 (31) , 7933-7935
Fast Electron Transport and High Surface Area: Potential Application of Porous Anatase Single Crystals in Solar Cells
- 2 July 2013
- Published by Wiley in Angewandte Chemie International Edition
- Vol. 52 (31) , 7933-7935
Fast Electron Transport and High Surface Area: Potential Application of Porous Anatase Single Crystals in Solar Cells
- 1 February 2013
- Vol. 13 (2) , 194-200
Adhesion of osteoblasts to a vertically aligned TiO2 nanotube surface.
The adhesion of cells to vertically aligned TiO2 nanotubes is reviewed. The attraction between a negatively charged nanotube surface and a negatively charged osteoblast is facilitated by charged protein-mediators like proteins with a quadrupolar internal charge distribution, fibronectin and vitronectin. It is shown that adhesion and spreading of osteoblasts on vertically aligned TiO2 nanotube surfaces depend on the diameter of the nanotubes. Apparently, a small diameter nanotube surface has on average more sharp convex edges per unit area than a large one, leading to stronger binding affinity on its surface.
- 1 February 2013
- Vol. 13 (2) , 194-200
Adhesion of osteoblasts to a vertically aligned TiO2 nanotube surface.
The adhesion of cells to vertically aligned TiO2 nanotubes is reviewed. The attraction between a negatively charged nanotube surface and a negatively charged osteoblast is facilitated by charged protein-mediators like proteins with a quadrupolar internal charge distribution, fibronectin and vitronectin. It is shown that adhesion and spreading of osteoblasts on vertically aligned TiO2 nanotube surfaces depend on the diameter of the nanotubes. Apparently, a small diameter nanotube surface has on average more sharp convex edges per unit area than a large one, leading to stronger binding affinity on its surface.
- 2 October 2012
- Published by Wiley in Chemphyschem
- Vol. 13 (17) , 3790-3793
Advanced Geometries of PEDOT Formed in Titania Nanotubes
- 2 October 2012
- Published by Wiley in Chemphyschem
- Vol. 13 (17) , 3790-3793
Advanced Geometries of PEDOT Formed in Titania Nanotubes
- Top Cited Papers
A Review of Photocatalysis using Self‐organized TiO2 Nanotubes and Other Ordered Oxide Nanostructures
Photocatalytic approaches, that is the reaction of light‐produced charge carriers at a semiconductor surface with their environment, currently attract an extremely wide scientific interest. This is to a large extent due to the high expectations: i) to convert sunlight directly into an energy carrier (H2), ii) to stimulate chemical synthetic reactions, or iii) to degrade unwanted environmental pollutants. Since the early reports in 1972, TiO2 has been the most investigated photocatalytic material by far; this originates from its outstanding electronic properties that allow for a wide range of applications. Not only the material, but also its structure and morphology, can have a considerable influence on the photocatalytic performance of TiO2. In recent years, particularly 1D (or pseudo 1D) structures such as nanowires and nanotubes have received great attention. The present Review focuses on TiO2 nanotube arrays (and similar structures) that grow by self‐organizing electrochemistry (highly aligned) from a Ti metal substrate. Herein, the growth, properties, and applications of these tubes are discussed, as well as ways and means to modify critical tube properties. Common strategies are addressed to improve the performance of photocatalysts such as doping or band‐gap engineering, co‐catalyst decoration, junction formation, or applying external bias. Finally, some unique applications of the ordered tube structures in various photocatalytic approaches are outlined.
Top Cited PapersA Review of Photocatalysis using Self‐organized TiO2 Nanotubes and Other Ordered Oxide Nanostructures
Photocatalytic approaches, that is the reaction of light‐produced charge carriers at a semiconductor surface with their environment, currently attract an extremely wide scientific interest. This is to a large extent due to the high expectations: i) to convert sunlight directly into an energy carrier (H2), ii) to stimulate chemical synthetic reactions, or iii) to degrade unwanted environmental pollutants. Since the early reports in 1972, TiO2 has been the most investigated photocatalytic material by far; this originates from its outstanding electronic properties that allow for a wide range of applications. Not only the material, but also its structure and morphology, can have a considerable influence on the photocatalytic performance of TiO2. In recent years, particularly 1D (or pseudo 1D) structures such as nanowires and nanotubes have received great attention. The present Review focuses on TiO2 nanotube arrays (and similar structures) that grow by self‐organizing electrochemistry (highly aligned) from a Ti metal substrate. Herein, the growth, properties, and applications of these tubes are discussed, as well as ways and means to modify critical tube properties. Common strategies are addressed to improve the performance of photocatalysts such as doping or band‐gap engineering, co‐catalyst decoration, junction formation, or applying external bias. Finally, some unique applications of the ordered tube structures in various photocatalytic approaches are outlined.
- 25 June 2012
- Published by Wiley in Chemistry – A European Journal
- Vol. 18 (31) , 9521-9524
Formation of Highly Ordered Nanochannel Nb Oxide by Self‐Organizing Anodization
- 25 June 2012
- Published by Wiley in Chemistry – A European Journal
- Vol. 18 (31) , 9521-9524
Formation of Highly Ordered Nanochannel Nb Oxide by Self‐Organizing Anodization