Iñaki Mondragon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Iñaki Mondragon has a total of 129 co-authors. Here are the top co-authors by number of shared publications:
- Galder Kortaberria
Group ‘Materials + Technologies’ (GMT), Chemical and Environmental Engineering Department, Faculty of Engineering of Gipuzkoa, University of the Basque Country (UPV/EHU), Plaza Europa 1, 20018 Donostia-San Sebastian, Spain
12 shared publications - Agnieszka Tercjak
Group ‘Materials+ Technologies’ (GMT), Department of Chemical and Environmental Engineering, University of the Basque Country (UPV/EHU), Plaza Europa 1, 20018 Donostia-San Sebastián, Spain
11 shared publications - Nagore Gabilondo
“Materials + Technologies” Group (GMT), Department of Chemical and Environmental Engineering, Faculty of Engineering of Gipuzkoa, University of the Basque Country (UPV/EHU), 20018 Donostia-San Sebastián, Spain
7 shared publications - Koro de la Caba
BIOMAT research group, University of the Basque Country (UPV/EHU), Escuela de Ingeniería de Gipuzkoa, Plaza de Europa 1, 20018 Donostia-San Sebastián, Spain
6 shared publications M. Blanco
Universidad País Vasco/Euskal Herriko Unibertsitatea
6 shared publicationsM. López
Universidad País Vasco/Euskal Herriko Unibertsitatea
6 shared publications
Latest Publications
- 18 December 2012
- Published by Wiley in Macromolecular Symposia
- Vol. 321-322 (1) , 99-104
Multifunctional Nanostructured Composites Based on TiO2Nanoparticles
- 18 December 2012
- Published by Wiley in Macromolecular Symposia
- Vol. 321-322 (1) , 99-104
Multifunctional Nanostructured Composites Based on TiO2Nanoparticles
- 18 December 2012
- Published by Wiley in Macromolecular Symposia
- Vol. 321-322 (1) , 112-117
In Situ Synthetized Silver/Epoxy Nanocomposites: Electrical Characterization in Terms of Dielectric Relaxation Spectroscopy
- 18 December 2012
- Published by Wiley in Macromolecular Symposia
- Vol. 321-322 (1) , 112-117
In Situ Synthetized Silver/Epoxy Nanocomposites: Electrical Characterization in Terms of Dielectric Relaxation Spectroscopy
- 27 January 2012
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 45 (3) , 1483-1491
Block Copolymer Concentration Gradient and Solvent Effects on Nanostructuring of Thin Epoxy Coatings Modified with Epoxidized Styrene–Butadiene–Styrene Block Copolymers
- 27 January 2012
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 45 (3) , 1483-1491
Block Copolymer Concentration Gradient and Solvent Effects on Nanostructuring of Thin Epoxy Coatings Modified with Epoxidized Styrene–Butadiene–Styrene Block Copolymers
- 16 January 2012
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 125 (2) , 1552-1558
Silicon and carbon substrates induced arrangement changes in poly(styrene‐b‐isoprene‐b‐styrene) block copolymer thin films
Poly(styrene‐b‐isoprene‐b‐styrene) (SIS) block copolymer ordering in thin films was studied using two selective substrates as carbon and silicon. Atomic force microscopy (AFM) and contact angle measurements were employed to examine the affinities between domains and surrounding interfaces. The surface morphology was examined by AFM using different amplitude ratios. Results showed polyisoprene (PI) domain layer formation in the outermost film layer. On the other hand, the layer close to substrate adopted different arrangements on silicon and carbon substrates. Topographical and phase images revealed that in both substrates with the thickest films, the interactions between substrate and block domains were not enough to induce surface ordering being the morphology independent of employed substrate. However, decreasing film thickness, SIS thin films displayed a variety of arrangements such as perforated lamellae and cylindrical morphologies. Depending on substrate, these morphologies were achieved in different film thicknesses. Finally, the thinnest film did not adjust to characteristic domain spacing commensurability and terraces formation was observed. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012
- 16 January 2012
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 125 (2) , 1552-1558
Silicon and carbon substrates induced arrangement changes in poly(styrene‐b‐isoprene‐b‐styrene) block copolymer thin films
Poly(styrene‐b‐isoprene‐b‐styrene) (SIS) block copolymer ordering in thin films was studied using two selective substrates as carbon and silicon. Atomic force microscopy (AFM) and contact angle measurements were employed to examine the affinities between domains and surrounding interfaces. The surface morphology was examined by AFM using different amplitude ratios. Results showed polyisoprene (PI) domain layer formation in the outermost film layer. On the other hand, the layer close to substrate adopted different arrangements on silicon and carbon substrates. Topographical and phase images revealed that in both substrates with the thickest films, the interactions between substrate and block domains were not enough to induce surface ordering being the morphology independent of employed substrate. However, decreasing film thickness, SIS thin films displayed a variety of arrangements such as perforated lamellae and cylindrical morphologies. Depending on substrate, these morphologies were achieved in different film thicknesses. Finally, the thinnest film did not adjust to characteristic domain spacing commensurability and terraces formation was observed. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012
- 30 December 2011
- Published by Wiley in Polymer Engineering & Science
- Vol. 52 (6) , 1161-1172
Influence of cure conditions on properties of resol/layered silicate nanocomposites
The effects on clay exfoliation of organic modification of montmorillonite (MMT) and the nature of the catalyst used during the synthesis and curing of a MMT modified phenolic resol resin were investigated. The impact on the final properties of other parameters such as reactivity ratio and temperature of condensation were also analyzed in order to optimize the conditions to prepare a customized organoclay‐based nanocomposite. Nanocomposites were analyzed by means of wide angle X‐ray scattering (WAXS), optical microscopy (TOM), and atomic force microscopy (AFM) techniques. The formation of either intercalated or quasi‐exfoliated structure was assessed in some systems. Thermal and mechanical properties of the cured composites were evaluated and correlated to their morphologies. More homogenous clay dispersion was achieved for composites prepared with aminoacid‐modified MMT, triethylamine (TEA) as catalyst, formaldehyde/phenol molar ratio (F/P) 2.0, and curing at 80°C. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers
- 30 December 2011
- Published by Wiley in Polymer Engineering & Science
- Vol. 52 (6) , 1161-1172
Influence of cure conditions on properties of resol/layered silicate nanocomposites
The effects on clay exfoliation of organic modification of montmorillonite (MMT) and the nature of the catalyst used during the synthesis and curing of a MMT modified phenolic resol resin were investigated. The impact on the final properties of other parameters such as reactivity ratio and temperature of condensation were also analyzed in order to optimize the conditions to prepare a customized organoclay‐based nanocomposite. Nanocomposites were analyzed by means of wide angle X‐ray scattering (WAXS), optical microscopy (TOM), and atomic force microscopy (AFM) techniques. The formation of either intercalated or quasi‐exfoliated structure was assessed in some systems. Thermal and mechanical properties of the cured composites were evaluated and correlated to their morphologies. More homogenous clay dispersion was achieved for composites prepared with aminoacid‐modified MMT, triethylamine (TEA) as catalyst, formaldehyde/phenol molar ratio (F/P) 2.0, and curing at 80°C. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers
- 30 October 2011
- Published by Springer Nature in Cellulose
- Vol. 19 (1) , 103-109
Sustainable optically transparent composites based on epoxidized soy-bean oil (ESO) matrix and high contents of bacterial cellulose (BC)
- 30 October 2011
- Published by Springer Nature in Cellulose
- Vol. 19 (1) , 103-109
Sustainable optically transparent composites based on epoxidized soy-bean oil (ESO) matrix and high contents of bacterial cellulose (BC)
- 5 October 2011
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 115 (45) , 22180-22185
Cellulose Nanocrystals and Au Nanoparticles Well-Dispersed in a Poly(styrene-b-ethylene oxide) Block Copolymer Matrix
- 5 October 2011
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 115 (45) , 22180-22185
Cellulose Nanocrystals and Au Nanoparticles Well-Dispersed in a Poly(styrene-b-ethylene oxide) Block Copolymer Matrix
- 1 June 2011
- Published by Elsevier in Electrochimica Acta
- Vol. 56 (16) , 5582-5586
Electrical properties of TiO2/SEO nanocomposites: From macro to nano
- 1 June 2011
- Published by Elsevier in Electrochimica Acta
- Vol. 56 (16) , 5582-5586
Electrical properties of TiO2/SEO nanocomposites: From macro to nano
- 10 February 2011
- Published by Wiley in Polymer International
- Vol. 60 (5) , 851-858
Property tailoring of phenol–formaldehyde matrices by control of reactant molar ratio and thermoplastic modification
High modulus, strength and thermal stability make phenol–formaldehyde resins (PFRs) interesting as matrices for nanocomposites. Four PFR matrices synthesized with different formaldehyde (F) to phenol (P) molar ratios were investigated, as well as the influence of thermoplastic modification on their mechanical properties. The effectiveness of a specific curing cycle for obtaining macrovoid‐ and microvoid‐free specimens by controlling the thickness of samples is demonstrated. Fourier transform infrared spectroscopy results reveal that F content increases the presence of oxidized linkages as benzophenones and fully substituted aromatic structures. PFR matrices with highest F content present the highest values of main transition temperature and flexural modulus up to an F/P ratio of 1.8, revealing the achievement of a densely crosslinked and rigid structure. A selected PFR matrix was modified with 5, 10 and 15 wt% of two poly(vinyl butyral) (PVB) thermoplastics of differing molecular weight. Phase separation occurs before gelation in all cases leading to different morphologies, observed using atomic force microscopy and optical microscopy, depending on PVB content: PVB‐rich particles in PFR‐rich matrix for 5 wt% and co‐continuous dual morphology for 10 and 15 wt% for both PVBs. Strength improvement is achieved for PFR matrices modified with 5 wt% of PVB associated with a tailored particulate morphology with a particle size of around 1.2 µm. Finally, 5 and 10 wt% PVB‐modified PFR materials exhibit a very high thermal stability with degradation temperatures very close to those for neat PFR matrix. Copyright © 2011 Society of Chemical Industry
- 10 February 2011
- Published by Wiley in Polymer International
- Vol. 60 (5) , 851-858
Property tailoring of phenol–formaldehyde matrices by control of reactant molar ratio and thermoplastic modification
High modulus, strength and thermal stability make phenol–formaldehyde resins (PFRs) interesting as matrices for nanocomposites. Four PFR matrices synthesized with different formaldehyde (F) to phenol (P) molar ratios were investigated, as well as the influence of thermoplastic modification on their mechanical properties. The effectiveness of a specific curing cycle for obtaining macrovoid‐ and microvoid‐free specimens by controlling the thickness of samples is demonstrated. Fourier transform infrared spectroscopy results reveal that F content increases the presence of oxidized linkages as benzophenones and fully substituted aromatic structures. PFR matrices with highest F content present the highest values of main transition temperature and flexural modulus up to an F/P ratio of 1.8, revealing the achievement of a densely crosslinked and rigid structure. A selected PFR matrix was modified with 5, 10 and 15 wt% of two poly(vinyl butyral) (PVB) thermoplastics of differing molecular weight. Phase separation occurs before gelation in all cases leading to different morphologies, observed using atomic force microscopy and optical microscopy, depending on PVB content: PVB‐rich particles in PFR‐rich matrix for 5 wt% and co‐continuous dual morphology for 10 and 15 wt% for both PVBs. Strength improvement is achieved for PFR matrices modified with 5 wt% of PVB associated with a tailored particulate morphology with a particle size of around 1.2 µm. Finally, 5 and 10 wt% PVB‐modified PFR materials exhibit a very high thermal stability with degradation temperatures very close to those for neat PFR matrix. Copyright © 2011 Society of Chemical Industry
- 1 January 2011
- Published by Elsevier
Contributor contact details