Pekka Alitalo
Research Subjects
Pekka Alitalo has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Sergei A. Tretyakov
Aalto University
11 shared publications Joni Vehmas
Department of Radio Science and Engineering/SMARAD Center of Excellence, Aalto University, Finland
3 shared publicationsOlli Luukkonen
Department of Radio Science and Engineering/SMARAD Center of Excellence, TKK Helsinki University of Technology, FI‐02015 TKK, Finland
3 shared publicationsSergei Tretyakov
Department of Radio Science and Engineering/SMARAD Center of Excellence TKK Helsinki University of Technology P.O. Box 3000 FI-02015 TKK Finland
3 shared publications- A. J. Viitanen
Electromagnetics Laboratory, Helsinki University of Technology, Finland
2 shared publications - Constantin Simovski
St. Petersburg State University of Information Technologies, Mechanics, and Optics
2 shared publications
Latest Publications
- 9 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 10, 1594-1597
Transmission-Line Cloak as an Antenna
Transmission-line cloak provides a simple yet wideband solution for cloaking an object. In this letter, it is shown how the basic transmission-line cloak geometry can be modified so that the cloak structure itself acts as an antenna at a frequency well below the cloaking frequency. The structure retains its cloaking properties despite these modifications. Two types of cloak-antennas are presented: a dipole antenna and a monopole antenna. The operation of these antennas is verified using simulations and measurements. It is also shown how the antenna resonance frequency can be tuned by changing its geometry.
- 9 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 10, 1594-1597
Transmission-Line Cloak as an Antenna
Transmission-line cloak provides a simple yet wideband solution for cloaking an object. In this letter, it is shown how the basic transmission-line cloak geometry can be modified so that the cloak structure itself acts as an antenna at a frequency well below the cloaking frequency. The structure retains its cloaking properties despite these modifications. Two types of cloak-antennas are presented: a dipole antenna and a monopole antenna. The operation of these antennas is verified using simulations and measurements. It is also shown how the antenna resonance frequency can be tuned by changing its geometry.
- Open Access
Cloaking a metal object from an electromagnetic pulse: A comparison between various cloaking techniques
Electromagnetic cloaks are devices that can be used to reduce the total scattering cross section of various objects. An ideal cloak removes all scattering from an object and thus makes this object "invisible" to the electromagnetic fields that impinge on the object. However, ideal cloaking appears to be possible only at a single frequency. To study cloaking from an electromagnetic pulse we consider propagation of a pulse inside a waveguide with a cloaked metal object inside. There are several ways to achieve cloaking and in this paper we study three such methods, namely, the coordinate-transformation cloak, the transmission-line cloak, and the metal-plate cloak. In the case of the two last cloaks, pulse propagation is studied using experimental data whereas the coordinate-transformation cloak is studied with numerical simulations. The results show that, at least in the studied cases where the cloaked object's diameter is smaller than the wavelength, the cloaks based on transmission-line meshes and metal plates have wider bandwidth than the coordinate-transformation cloak.
Open AccessCloaking a metal object from an electromagnetic pulse: A comparison between various cloaking techniques
Electromagnetic cloaks are devices that can be used to reduce the total scattering cross section of various objects. An ideal cloak removes all scattering from an object and thus makes this object "invisible" to the electromagnetic fields that impinge on the object. However, ideal cloaking appears to be possible only at a single frequency. To study cloaking from an electromagnetic pulse we consider propagation of a pulse inside a waveguide with a cloaked metal object inside. There are several ways to achieve cloaking and in this paper we study three such methods, namely, the coordinate-transformation cloak, the transmission-line cloak, and the metal-plate cloak. In the case of the two last cloaks, pulse propagation is studied using experimental data whereas the coordinate-transformation cloak is studied with numerical simulations. The results show that, at least in the studied cases where the cloaked object's diameter is smaller than the wavelength, the cloaks based on transmission-line meshes and metal plates have wider bandwidth than the coordinate-transformation cloak.
- 17 April 2009
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 51 (7) , 1627-1631
Broadband cloaking with volumetric structures composed of two-dimensional transmission-line networks
- 17 April 2009
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 51 (7) , 1627-1631
Broadband cloaking with volumetric structures composed of two-dimensional transmission-line networks
- 5 January 2009
- Published by AIP Publishing in Applied Physics Letters
- Vol. 94 (1) , 014103
Experimental verification of broadband cloaking using a volumetric cloak composed of periodically stacked cylindrical transmission-line networks
Cloaking using a volumetric structure composed of stacked two-dimensional transmission-line networks is verified with numerical simulations and measurements. The measurements are done in a waveguide, in which an array of metal cylinders is inserted causing a short circuit in the waveguide. The metal cylinders are cloaked using the transmission-line structure, which “hides” the cylinders and thus enables wave propagation inside the waveguide.
- 5 January 2009
- Published by AIP Publishing in Applied Physics Letters
- Vol. 94 (1) , 014103
Experimental verification of broadband cloaking using a volumetric cloak composed of periodically stacked cylindrical transmission-line networks
Cloaking using a volumetric structure composed of stacked two-dimensional transmission-line networks is verified with numerical simulations and measurements. The measurements are done in a waveguide, in which an array of metal cylinders is inserted causing a short circuit in the waveguide. The metal cylinders are cloaked using the transmission-line structure, which “hides” the cylinders and thus enables wave propagation inside the waveguide.
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 285-288
Controllable Waveguide Based on Capacitively Loaded Wire Medium
In this presentation we discuss dispersion, losses and excitation of metal waveguides, filled with wire media, loaded by tunable capacitances. Standard rectangular and square cross section waveguides are considered. The waveguides can be filled with usual (single) and crossed (double) wire media (WM). In the standard waveguides, filled with the single WM, capacitances, inserted near wide walls, create pass bands located much lower than the cutoff frequency. For example, in the waveguide, having the cutoff frequency 26 GHz, we have found propagating modes in the frequency range 5-10 GHz. Dispersion of modes in these pass bands is very sensitive to a change of capacitances. Such loaded waveguides can form a new class of controllable microwave devices. Tunability of modes, propagating below the cutoff of the empty waveguide, is studied numerically and experimentally.
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 285-288
Controllable Waveguide Based on Capacitively Loaded Wire Medium
In this presentation we discuss dispersion, losses and excitation of metal waveguides, filled with wire media, loaded by tunable capacitances. Standard rectangular and square cross section waveguides are considered. The waveguides can be filled with usual (single) and crossed (double) wire media (WM). In the standard waveguides, filled with the single WM, capacitances, inserted near wide walls, create pass bands located much lower than the cutoff frequency. For example, in the waveguide, having the cutoff frequency 26 GHz, we have found propagating modes in the frequency range 5-10 GHz. Dispersion of modes in these pass bands is very sensitive to a change of capacitances. Such loaded waveguides can form a new class of controllable microwave devices. Tunability of modes, propagating below the cutoff of the empty waveguide, is studied numerically and experimentally.
- 1 March 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 147-150
Cylindrical Transmission-Line Cloak for Microwave Frequencies
We present design and simulations of a cylindrical electromagnetic cloak which is based on a method employing periodic meshes of transmission-line networks. The cloaked object can be a connected or non-connected mesh of inclusions composed of an arbitrary material. In the example case studied in this work, we cloak a cylindrical mesh of rods made of a perfect electric conductor. Since the period of the cloaked object's inclusions is much smaller than the wavelength of the impinging radiation, the cloaked object is effectively impenetrable to the electromagnetic fields. When placed inside the proposed cloak, the total scattering cross section of the system is shown to be highly reduced in a large bandwidth, when compared to the case without the cloak.
- 1 March 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 147-150
Cylindrical Transmission-Line Cloak for Microwave Frequencies
We present design and simulations of a cylindrical electromagnetic cloak which is based on a method employing periodic meshes of transmission-line networks. The cloaked object can be a connected or non-connected mesh of inclusions composed of an arbitrary material. In the example case studied in this work, we cloak a cylindrical mesh of rods made of a perfect electric conductor. Since the period of the cloaked object's inclusions is much smaller than the wavelength of the impinging radiation, the cloaked object is effectively impenetrable to the electromagnetic fields. When placed inside the proposed cloak, the total scattering cross section of the system is shown to be highly reduced in a large bandwidth, when compared to the case without the cloak.
- 1 March 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 282-285
Microwave Transmission-Line Lens Matched with Free Space
In order to mitigate the problem of unwanted reflections from a homogeneous dielectric lens, a lens based on periodic networks of transmission lines is proposed. Since the propagation constant and the impedance of the network can be varied to a large extent independently from each other, it is possible to realize a lens with a high index of refraction while having almost perfect impedance matching with the surrounding medium.
- 1 March 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 282-285
Microwave Transmission-Line Lens Matched with Free Space
In order to mitigate the problem of unwanted reflections from a homogeneous dielectric lens, a lens based on periodic networks of transmission lines is proposed. Since the propagation constant and the impedance of the network can be varied to a large extent independently from each other, it is possible to realize a lens with a high index of refraction while having almost perfect impedance matching with the surrounding medium.
- Open Access
Impedance-matched microwave lens
A microwave lens with highly reduced reflectance, as compared to conventional dielectric lenses, is proposed. The lens is based on two-dimensional or three-dimensional transmission-line networks that can be designed to have an effective refractive index larger than one, while having almost perfect impedance matching with free space. The design principles are presented and an example lens is studied using commercial simulation software.
Open AccessImpedance-matched microwave lens
A microwave lens with highly reduced reflectance, as compared to conventional dielectric lenses, is proposed. The lens is based on two-dimensional or three-dimensional transmission-line networks that can be designed to have an effective refractive index larger than one, while having almost perfect impedance matching with free space. The design principles are presented and an example lens is studied using commercial simulation software.
- Open Access
A three-dimensional backward-wave network matched with free space
A backward-wave slab based on a capacitively and inductively loaded three-dimensional transmission-line network is designed in such a way that impedance-matching with free space is obtained. To enable field propagation from free space to the network and vice versa, the use of a transition layer is proposed. Matching of the designed network with free space and negative refraction occurring at the slab interfaces are confirmed with full-wave simulations.
Open AccessA three-dimensional backward-wave network matched with free space
A backward-wave slab based on a capacitively and inductively loaded three-dimensional transmission-line network is designed in such a way that impedance-matching with free space is obtained. To enable field propagation from free space to the network and vice versa, the use of a transition layer is proposed. Matching of the designed network with free space and negative refraction occurring at the slab interfaces are confirmed with full-wave simulations.
- Open Access
Subwavelength resolution with three-dimensional isotropic transmission-line lenses
Dispersion, impedance matching and resolution characteristics of an isotropic three-dimensional flat lens ("superlens") are studied. The lens is based on cubic meshes of interconnected transmission lines and bulk loads. We study a practical realization of the lens, based on the microstrip technology. The dispersion equations that have been previously derived, are verified with full-wave simulations. The isotropy of the structure is verified with analytical as well as simulation results. The resolution characteristics of a practically realizable, lossy lens are studied analytically.
Open AccessSubwavelength resolution with three-dimensional isotropic transmission-line lenses
Dispersion, impedance matching and resolution characteristics of an isotropic three-dimensional flat lens ("superlens") are studied. The lens is based on cubic meshes of interconnected transmission lines and bulk loads. We study a practical realization of the lens, based on the microstrip technology. The dispersion equations that have been previously derived, are verified with full-wave simulations. The isotropy of the structure is verified with analytical as well as simulation results. The resolution characteristics of a practically realizable, lossy lens are studied analytically.