LPLudovic Pauchard

Ludovic Pauchard

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ludovic Pauchard has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Drying drops

    by F. Giorgiutti-Dauphiné, L. Pauchard


  • Elapsed time for crack formation during drying

    by F. Giorgiutti-Dauphiné, L. Pauchard

    The drying of colloidal films usually leads to mechanical instabilities that affect the uniformity of the final deposit. The resulting patterns are the signature of the mechanical stress, and reveal the way the system consolidates. We report experimental results on the crack patterns induced by the drying of sessile drops of concentrated dispersions. Crack patterns exhibit a well-defined spatial order, and a regular temporal periodicity. In addition, the onset of cracking occurs after a well-defined elapsed time that depends on the mechanical properties of the gel, and on the drying kinetics. The estimation of the time elapsed before cracks form is related to the elastic properties of the material. This is supported by quantitative measurements using indentation testing and by a simple scaling law derived from poro-elastic theory.


  • Open Access

    The buckling and invagination process during consolidation of colloidal droplets

    by F. Boulogne, F. Giorgiutti-Dauphiné, L. Pauchard

    Drying a droplet of colloidal dispersion can result in complex pattern formation due to both development and deformation of a skin at the drop surface. The present study focuses on the drying process of droplets of colloidal dispersions in a confined geometry where direct observations of the skin thickness are allowed. During the drying process, a buckling process is followed by a single depression growth inside the drop. The deformation of the droplet is found to be generic and is studied for various colloidal dispersions. The final shape can be partly explained by simple energy analysis based on the competition between bending and stretching deformations. Particularly, the final shape enables us to determine precisely the critical thickness of the shell for buckling. This study allows us to validate theory in 2D droplets and apply it to the case of 3D droplets where the thickness is not accessible by direct observation.


  • Effect of a non-volatile cosolvent on crack patterns induced by desiccation of a colloidal gel

    by F. Boulogne, L. Pauchard, F. Giorgiutti-Dauphiné

    The consolidation of colloidal gels results in enormous stresses that are usually released by the formation of undesirable cracks. The capacity of a gel network to crack during drying depends on the existence and significance of a pressure gradient in the pore liquid; in addition it depends on the way the gel relaxes the resulting drying stresses. In this paper the effect of a binary mixture of solvents saturating the gel network on the crack patterns formation is investigated. Indeed, incorporation of a small quantity of non-volatile cosolvent, i.e. glycerol, inhibits drying-induced cracks; moreover addition of a concentration greater than 10% to a colloidal dispersion leads to a crack free coating under room conditions. Mass variation with time reveals that both evaporation rate and cracking time are not affected by glycerol, in the range of added glycerol contents studied. In addition measurements of mechanical properties show that the elastic modulus is reduced with glycerol content. The decrease of the number of cracks with the glycerol content is related to the flattening of the pressure gradient in the pore liquid. The mechanism is shown to be due to the combination of two processes: flow driven by the pressure gradient and diffusion mechanisms in accordance with Scherer's work (1989).


  • Instability and morphology of polymer solutions coating a fibre

    by F. Boulogne, L. Pauchard, F. Giorgiutti-Dauphiné

    We report an experimental study on the dynamics of a thin film of polymer solution coating a vertical fibre. The liquid film has first a constant thickness and then undergoes the Plateau–Rayleigh instability, which leads to the formation of sequences of drops, separated by a thin film, moving down at a constant velocity. Different polymer solutions are used, i.e. xanthan solutions and polyacrylamide (PAAm) solutions. These solutions both exhibit shear-rate dependence of the viscosity, but for PAAm solutions, there are strong normal stresses in addition to the shear thinning effect. We characterize experimentally and separately the effects of these two non-Newtonian properties on the flow on the fibre. Thus, in the flat film observed before the emergence of the drops, only the shear-thinning effect plays a role, and tends to thin the film compared to the Newtonian case. The effect of the non-Newtonian rheology on the Plateau–Rayleigh instability is then investigated through the measurements of the growth rate and the wavelength of the instability. Results are in good agreement with linear stability analysis for a shear-thinning fluid. The effect of normal stress can be taken into account by considering an effective surface tension, which tends to decrease the growth rate of the instability. Finally, the dependence of the morphology of the drops on normal stress is investigated, and a simplified model including the normal stress within the lubrication approximation provides good quantitative results on the shape of the drops.


  • From craquelures to spiral crack patterns: influence of layer thickness on the crack patterns induced by desiccation

    by V. Lazarus, L. Pauchard

    As a film of dispersed colloidal particles consolidates by desiccation on a rigid substrate, enormous stresses develop. Most of the time, these stresses exceed the strength of the material causing crack formation. Although undesirable in most industrial cases, crack patterns exhibit a useful method to characterize paintings. Indeed, crack patterns are the signature of the particles, solvent and substrate type, the drying conditions and the film thickness. Here we focus on the influence of this last parameter on the final crack morphologies. In particular, using a colloidal dispersion with transparency properties, we observe that craquelures, delamination and spiral crack morphologies can be obtained by changing only the film thickness. An extensive description of the formation dynamics and final geometry of each pattern is presented, highlighting the key geometric parameters that may easily be used by a broad audience, including the mechanical engineering, physics, chemistry, geology and art communities.


  • Influence of Mechanical Properties of Nanoparticles on Macrocrack Formation

    by Ludovic Pauchard, Bérengère Abou, Ken Sekimoto

    We present an experimental investigation of drying suspensions of both hard and soft nanolatex spheres. The crack formation is examined as a function of the proportion of hard and soft deformable particles, leading to tunable elastic properties of the drying film. In our experimental systems, no crack formation could be observed below an onset value of the proportion in hard spheres ϕ ∼ 0.45 . During the drying process, the mass of films with various compositions in hard and soft spheres is measured as a function of time. The results suggest that the soft particles undergo deformation that releases the internal stresses.


  • Open Access

    Influence of nanoparticles mechanical properties on macrocracks formation

    by L. Pauchard, B. Abou, K. Sekimoto

    We present an experimental investigation of drying suspensions of both hard and soft nanolatex spheres. The crack formation is examined as a function of the proportion of hard and soft deformable particles, leading to tunable elastic properties of the drying film. In our experiments corresponding to a given layer thickness, no crack formation could be observed below an onset value of the proportion in hard spheres around 0.45. During the drying process, the mass of films with various compositions in hard and soft spheres is measured as a function of time. The results suggest that the soft particles undergo deformation that releases the internal stresses. The spacing between cracks is measured as a function of the layer thickness for various compositions in hard and soft spheres.

  • Craquelures dans les couches picturales des peintures d’art

    by Ludovic Pauchard, Véronique Lazarus, Bérengère Abou, Ken Sekimoto, Geneviève Aitken, Christian Lahanier


  • Imbibition, desiccation and mechanical deformations of zein pills in relation to their porosity

    by M. A. Sabino, L. Pauchard, C. Allain, P. Colonna, D. Lourdin

    . This paper deals with the interaction between zein (the main protein component of corn grain) and water. It induces macroscopic properties changes and may allow for the understanding of the basis of zein endosperm structure: vitreous endosperm is compact and floury endosperm is porous, giving the endosperm its hard and soft textures, respectively. In that aim porous pills made by compaction of zein powder submitted to different hydration/dehydration processes have been prepared and studied. In particular, imbibition measurements of a pure-water drop deposited onto a zein pill were performed. Also, desiccation of a zein pill previously imbibed induces strong mechanical stresses leading to crack formation and/or large deformations.