Pramod S. Mehta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pramod S. Mehta has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Anand Krishnasamy
Department of Mechanical Engineering, Indian Institute of Technology Madras, Chennai, India
2 shared publications - Avishek Ranjan
Department of Mechanical Engineering Indian Institute of Technology Bombay 400076 Mumbai Maharashtra India
1 shared publication - J. Thangaraja
Indian Institute of Technology Madras
1 shared publication - Shamit Bakshi
Indian Institute of Technology Madras
1 shared publication - Sundararajan Rajkumar
Sri Sivasubramaniya Nadar College of Engineering
1 shared publication Thangaraja Jeyaseelan
Department of Mechanical Engineering, Indian Institute of Technology Madras, Chennai, India
1 shared publication
Latest Publications
- 9 August 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 138 (12) , 122805
Multizone Phenomenological Modeling of Combustion and Emissions for Multiple-Injection Common Rail Direct Injection Diesel Engines
Common rail direct injection (CRDI) system is a modern variant of direct injection diesel engine featuring higher fuel injection pressure and flexible injection scheduling which involves two or more pulses. Unlike a conventional diesel engine, the CRDI engine provides simultaneous reduction of oxides of nitrogen and smoke with an injection schedule that has optimized start of injection, fuel quantity in each injection pulse, and dwell periods between them. In this paper, the development of a multizone phenomenological model used for predicting combustion and emission characteristics of multiple injection in CRDI diesel engine is presented. The multizone spray configuration with their temperature and composition histories predicted on phenomenological spray growth and mixing considerations helps accurate prediction of engine combustion and emission (nitric oxide and soot) characteristics. The model predictions of combustion and emissions for multiple injection are validated with measured values over a wide range of speed and load conditions. The multizone and the two-zone model are compared and the reasons for better comparisons for the multizone model with experimental data are also explored.
- 9 August 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 138 (12) , 122805
Multizone Phenomenological Modeling of Combustion and Emissions for Multiple-Injection Common Rail Direct Injection Diesel Engines
Common rail direct injection (CRDI) system is a modern variant of direct injection diesel engine featuring higher fuel injection pressure and flexible injection scheduling which involves two or more pulses. Unlike a conventional diesel engine, the CRDI engine provides simultaneous reduction of oxides of nitrogen and smoke with an injection schedule that has optimized start of injection, fuel quantity in each injection pulse, and dwell periods between them. In this paper, the development of a multizone phenomenological model used for predicting combustion and emission characteristics of multiple injection in CRDI diesel engine is presented. The multizone spray configuration with their temperature and composition histories predicted on phenomenological spray growth and mixing considerations helps accurate prediction of engine combustion and emission (nitric oxide and soot) characteristics. The model predictions of combustion and emissions for multiple injection are validated with measured values over a wide range of speed and load conditions. The multizone and the two-zone model are compared and the reasons for better comparisons for the multizone model with experimental data are also explored.
- 5 July 2014
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 96 (2) , 135-143
Effect of Biodiesel on Thermal NO Formation
- 5 July 2014
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 96 (2) , 135-143
Effect of Biodiesel on Thermal NO Formation
- 13 May 2014
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 228 (11) , 1274-1284
Experimental investigations on the increase in nitric oxide emissions using biodiesels and their mitigation
One of the major shortcomings to be addressed in the widespread applications of biodiesel fuel for compression ignition engines is the formation of higher nitric oxide emissions. It is well established in the literature that thermal nitric oxide is a dominant source for nitric oxide formation in engines. Thermal nitric oxide formation increases by any in-cylinder combustion strategy that alters the in-cylinder temperatures, the oxygen fraction or the residence time of high-temperature post-flame burned gases. The differences between the properties of biodiesel in terms of a higher bulk modulus, a higher cetane number and the presence of a fuel-bound oxygen fraction and the properties of diesel are found to affect the in-cylinder charge conditions and thus the nitric oxide formation. The present work aims to understand the major contributor to the higher nitric oxide formation with biodiesel based on experimental investigations in two different engine configurations: one with a conventional mechanical-type injection system and the other with a modern common-rail direct-injection system. The experimental results highlight that the dynamic injection timing advanced up to a maximum of 2.6° crank angle owing to the higher bulk modulus of biodiesel. This factor contributes to specific nitric oxide emissions which are 7.5% higher in an engine having a mechanical-type injection system. The increase in the nitric oxide is neutralized on restoring the injection timing to that of the diesel injection time setting. In the case of an engine with a modern common-rail direct-injection system, the injection timings remain unaltered, and the nitric oxide concentrations for diesel and for biodiesel–diesel blends also remains the same.
- 13 May 2014
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 228 (11) , 1274-1284
Experimental investigations on the increase in nitric oxide emissions using biodiesels and their mitigation
One of the major shortcomings to be addressed in the widespread applications of biodiesel fuel for compression ignition engines is the formation of higher nitric oxide emissions. It is well established in the literature that thermal nitric oxide is a dominant source for nitric oxide formation in engines. Thermal nitric oxide formation increases by any in-cylinder combustion strategy that alters the in-cylinder temperatures, the oxygen fraction or the residence time of high-temperature post-flame burned gases. The differences between the properties of biodiesel in terms of a higher bulk modulus, a higher cetane number and the presence of a fuel-bound oxygen fraction and the properties of diesel are found to affect the in-cylinder charge conditions and thus the nitric oxide formation. The present work aims to understand the major contributor to the higher nitric oxide formation with biodiesel based on experimental investigations in two different engine configurations: one with a conventional mechanical-type injection system and the other with a modern common-rail direct-injection system. The experimental results highlight that the dynamic injection timing advanced up to a maximum of 2.6° crank angle owing to the higher bulk modulus of biodiesel. This factor contributes to specific nitric oxide emissions which are 7.5% higher in an engine having a mechanical-type injection system. The increase in the nitric oxide is neutralized on restoring the injection timing to that of the diesel injection time setting. In the case of an engine with a modern common-rail direct-injection system, the injection timings remain unaltered, and the nitric oxide concentrations for diesel and for biodiesel–diesel blends also remains the same.
- 21 January 2010
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 24 (1) , 664-672
Estimating the Viscosity of Vegetable Oil and Biodiesel Fuels
- 21 January 2010
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 24 (1) , 664-672
Estimating the Viscosity of Vegetable Oil and Biodiesel Fuels