Jing Fan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jing Fan has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
Jianji Wang
School of Chemistry and Environmental Science, Henan Key Laboratory for Environmental Pollution Control, Key Laboratory for Yellow River and Huai River Water Environmental and Pollution Control, Ministry of Education, Henan Normal University, Xinxiang, Henan 453007, P.R. China
6 shared publications- Maohong Fan
University of Wyoming
5 shared publications Pingan Peng
State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640, PR China
5 shared publicationsChunlai Wu
Department of Environmental and Chemical Engineering, Luoyang Institute of Science and Technology, Luoyang, Henan 471023, PR China
4 shared publicationsChuanyun Peng
2 shared publicationsGuoguang Liu
School of Chemistry and Environmental Science, Henan Key Laboratory for Environmental Pollution Control, Henan Normal University, Xinxiang, Henan 453007, PR China
2 shared publications
Latest Publications
- Open Access
Synthesis and Performance of Iron Oxide-Coated Ceramsite in a Biotrickling Filter for Nitric Oxide Removal under Thermophilic Conditions
A novel medium consisting of iron oxide-coated porous ceramsite (modified ceramsite) was investigated for NO removal under thermophilic conditions in this study. We used a surface coating method with FeCl3·6H2O as the modifier. When ceramsite was calcined for 4 h at 500 °C, the surface pH value decreased to 3.46, which is much lower than the isoelectric point of ceramsite, ensuring its surface was electropositive. The surface of modified ceramsite changed from two- to three-dimensional and exhibited excellent adsorption behavior to assist microbial growth; the maximum dry weight of the biofilm was 1.28 mg/g. It only took 8 days for the biofilter constructed from the modified ceramsite to start up, whereas that packed with commercial ceramsite took 22 days. The NO removal efficiency of the biofilter did not decrease apparently at high NO inlet concentration of above 1600 mg/m3 and maintained an average value of above 90% during the whole operation period. Additionally, the morphological observation showed that the loss of the surface coating was not obvious, and the coating properties remained stable during long-term operation. The maximum NO inlet loading of the biotrickling filter was 80 g/(m3·h) with an average removal efficiency of 91.1% along with a quick start-up when using the modified ceramsite filler. Thus, modified ceramsite can be considered a very effective medium in biotrickling filters for NO removal.
Open AccessSynthesis and Performance of Iron Oxide-Coated Ceramsite in a Biotrickling Filter for Nitric Oxide Removal under Thermophilic Conditions
A novel medium consisting of iron oxide-coated porous ceramsite (modified ceramsite) was investigated for NO removal under thermophilic conditions in this study. We used a surface coating method with FeCl3·6H2O as the modifier. When ceramsite was calcined for 4 h at 500 °C, the surface pH value decreased to 3.46, which is much lower than the isoelectric point of ceramsite, ensuring its surface was electropositive. The surface of modified ceramsite changed from two- to three-dimensional and exhibited excellent adsorption behavior to assist microbial growth; the maximum dry weight of the biofilm was 1.28 mg/g. It only took 8 days for the biofilter constructed from the modified ceramsite to start up, whereas that packed with commercial ceramsite took 22 days. The NO removal efficiency of the biofilter did not decrease apparently at high NO inlet concentration of above 1600 mg/m3 and maintained an average value of above 90% during the whole operation period. Additionally, the morphological observation showed that the loss of the surface coating was not obvious, and the coating properties remained stable during long-term operation. The maximum NO inlet loading of the biotrickling filter was 80 g/(m3·h) with an average removal efficiency of 91.1% along with a quick start-up when using the modified ceramsite filler. Thus, modified ceramsite can be considered a very effective medium in biotrickling filters for NO removal.
- 23 June 2014
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 16 (8) , 4009-4016
Highly efficient and reversible CO 2 adsorption by amine-grafted platelet SBA-15 with expanded pore diameters and short mesochannels
Amine-grafted mesoporous silica materials with short channels and large pore diameters have been prepared and used to adsorb CO 2 efficiently.
- 23 June 2014
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 16 (8) , 4009-4016
Highly efficient and reversible CO 2 adsorption by amine-grafted platelet SBA-15 with expanded pore diameters and short mesochannels
Amine-grafted mesoporous silica materials with short channels and large pore diameters have been prepared and used to adsorb CO 2 efficiently.
- Open Access
CO2 Capture and Separation Properties in the Ionic Liquid 1-n-Butyl-3-Methylimidazolium Nonafluorobutylsulfonate
Recently, the use of ionic liquids (ILs) for carbon capture and separation processes has gained great interest by many researchers due to the high solubility of CO2 in ILs. In the present work, solubility measurements of CO2 in the novel IL 1-n-butyl-3-methylimidazolium nonafluorobutylsulfonate [C4mim][CF3CF2CF2CF2SO3] were performed with a high-pressure view-cell technique in the temperature range from 293.15 to 343.15 K and pressures up to about 4.2 MPa. For comparison, solubilities of H2, N2, and O2 in the IL were also measured at 323.15 K via the same procedure. The Krichevsky-Kasarnovsky equation was employed to correlate the measured solubility data. Henry’s law constants, enthalpies, and entropies of absorption for CO2 in the IL were also determined and presented. The CO2 solubility in this IL was compared with other ILs sharing the same cation. It was shown that the solubility of CO2 in these ILs follows the sequence: [C4mim][CF3CF2CF2CF2SO3] ≈ [C4mim][Tf2N] > [C4mim][CF3CF2CF2COO] > [C4mim][BF4], and the solubility selectivity of CO2 relative to O2, N2, and H2 in [C4mim][CF3CF2CF2CF2SO3] was 8, 16, and 22, respectively. Furthermore, this IL is regenerable and exhibits good stability. Therefore, the IL reported here would be a promising sorbent for CO2.
Open AccessCO2 Capture and Separation Properties in the Ionic Liquid 1-n-Butyl-3-Methylimidazolium Nonafluorobutylsulfonate
Recently, the use of ionic liquids (ILs) for carbon capture and separation processes has gained great interest by many researchers due to the high solubility of CO2 in ILs. In the present work, solubility measurements of CO2 in the novel IL 1-n-butyl-3-methylimidazolium nonafluorobutylsulfonate [C4mim][CF3CF2CF2CF2SO3] were performed with a high-pressure view-cell technique in the temperature range from 293.15 to 343.15 K and pressures up to about 4.2 MPa. For comparison, solubilities of H2, N2, and O2 in the IL were also measured at 323.15 K via the same procedure. The Krichevsky-Kasarnovsky equation was employed to correlate the measured solubility data. Henry’s law constants, enthalpies, and entropies of absorption for CO2 in the IL were also determined and presented. The CO2 solubility in this IL was compared with other ILs sharing the same cation. It was shown that the solubility of CO2 in these ILs follows the sequence: [C4mim][CF3CF2CF2CF2SO3] ≈ [C4mim][Tf2N] > [C4mim][CF3CF2CF2COO] > [C4mim][BF4], and the solubility selectivity of CO2 relative to O2, N2, and H2 in [C4mim][CF3CF2CF2CF2SO3] was 8, 16, and 22, respectively. Furthermore, this IL is regenerable and exhibits good stability. Therefore, the IL reported here would be a promising sorbent for CO2.
- Open Access
- 1 September 2013
- Published by SAGE Publications in Adsorption Science & Technology
- Vol. 31 (9) , 791-806
A Surface Molecularly Imprinted Polymer for Selective Extraction and Liquid Chromatographic Determination of 4-Methylimidazole in Environmental Samples
A newly designed surface molecularly imprinted polymer (MIP) was developed using 4-methylimidazole as the template and ethylenediaminepoly (styrene-divinylbenzene) particles as the support material. The resulting MIP material was characterized with scanning electron microscopy, infrared spectrum, surface area, pore-size and thermal property measurements. Static adsorption, solid-phase extraction (SPE) and high-performance liquid chromatography were combined to study the adsorption characteristics and selective recognition performance of the polymer for 4-methylimidazole and its structural analogues. It was shown that the maximum binding capacities of 4-methylimidazole on the MIP and the non-imprinted polymer (NIP) were 416 and 227 µmol g−1 respectively. The binding process could be described by pseudo-second-order kinetics, and the adsorption equilibrium was achieved in 40 minutes. Compared with the corresponding NIP, the MIP exhibited much higher adsorption performance and selectivity for the template. After the separation of a mixture of 4-methylimidazole, benzimidazole and nitrophenol on the MIP–SPE and the NIP–SPE columns, the recoveries of 4-methylimidazole on the MIP–SPE and NIP–SPE columns were 96–102% and 34–39%, respectively, whereas those of benzimidazole and nitrophenol were below 19% on the two columns. In addition, more than 99% of 4-methylimidazole could be obtained on the MIP–SPE column from water and soil samples.
- 1 September 2013
- Published by SAGE Publications in Adsorption Science & Technology
- Vol. 31 (9) , 791-806
Open AccessA Surface Molecularly Imprinted Polymer for Selective Extraction and Liquid Chromatographic Determination of 4-Methylimidazole in Environmental Samples
A newly designed surface molecularly imprinted polymer (MIP) was developed using 4-methylimidazole as the template and ethylenediaminepoly (styrene-divinylbenzene) particles as the support material. The resulting MIP material was characterized with scanning electron microscopy, infrared spectrum, surface area, pore-size and thermal property measurements. Static adsorption, solid-phase extraction (SPE) and high-performance liquid chromatography were combined to study the adsorption characteristics and selective recognition performance of the polymer for 4-methylimidazole and its structural analogues. It was shown that the maximum binding capacities of 4-methylimidazole on the MIP and the non-imprinted polymer (NIP) were 416 and 227 µmol g−1 respectively. The binding process could be described by pseudo-second-order kinetics, and the adsorption equilibrium was achieved in 40 minutes. Compared with the corresponding NIP, the MIP exhibited much higher adsorption performance and selectivity for the template. After the separation of a mixture of 4-methylimidazole, benzimidazole and nitrophenol on the MIP–SPE and the NIP–SPE columns, the recoveries of 4-methylimidazole on the MIP–SPE and NIP–SPE columns were 96–102% and 34–39%, respectively, whereas those of benzimidazole and nitrophenol were below 19% on the two columns. In addition, more than 99% of 4-methylimidazole could be obtained on the MIP–SPE column from water and soil samples.
- 14 April 2010
- Published by Elsevier in Analytica Chimica Acta
- Vol. 665 (1) , 105
Corrigendum to “Simple and sensitive fluorimetric method for determination of environmental hormone bisphenol A based on its inhibitory effect on the redox reaction between peroxyl radical and rhodamine 6G” [Anal. Chim. Acta 585 (2007) 134–138]
- 14 April 2010
- Published by Elsevier in Analytica Chimica Acta
- Vol. 665 (1) , 105
Corrigendum to “Simple and sensitive fluorimetric method for determination of environmental hormone bisphenol A based on its inhibitory effect on the redox reaction between peroxyl radical and rhodamine 6G” [Anal. Chim. Acta 585 (2007) 134–138]
- Top Cited Papers
- 30 July 2009
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 166 (2-3) , 904-910
Rapid decolorization of azo dye methyl orange in aqueous solution by nanoscale zerovalent iron particles
- 30 July 2009
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 166 (2-3) , 904-910
Top Cited PapersRapid decolorization of azo dye methyl orange in aqueous solution by nanoscale zerovalent iron particles
- 27 April 2009
- Published by Elsevier in Analytica Chimica Acta
- Vol. 640 (1-2) , 58-62
An organic-reagent-free method for determination of chromium(VI) in steel alloys, sewage sludge and wastewater
- 27 April 2009
- Published by Elsevier in Analytica Chimica Acta
- Vol. 640 (1-2) , 58-62
An organic-reagent-free method for determination of chromium(VI) in steel alloys, sewage sludge and wastewater
- 1 April 2009
- Published by Elsevier in Analytica Chimica Acta
- Vol. 639 (1-2) , 42-50
Study of molecularly imprinted solid-phase extraction of diphenylguanidine and its structural analogs
- 1 April 2009
- Published by Elsevier in Analytica Chimica Acta
- Vol. 639 (1-2) , 42-50
Study of molecularly imprinted solid-phase extraction of diphenylguanidine and its structural analogs
- 17 March 2009
- Published by Wiley in Luminescence
- Vol. 24 (4) , 266-270
A novel inhibitory kinetic fluorimetric method for the determination of trace methomyl in environmental samples
A novel inhibitory kinetic fluorimetric method for the determination of trace methomyl was proposed. It was shown that the Fenton reagent oxidized rhodamine B in acid medium which enabled the fluorescence quenching of the latter. The presence of trace methomyl clearly inhibited the reaction. Upon addition of EDTA, a good linear relationship between the inhibitory effect and the concentration of methomyl was observed, together with improved stabilization and sensitivity. Factors affecting the determination of trace methomyl were investigated systematically. Under the optimum conditions, the linear range for the determination of methomyl was 0.04–2.2 µg/mL; the detection limit and the quantification limit for methomyl were 0.011 and 0.037 µg/mL, respectively. The proposed method was applied to the determination of methomyl in four environmental soil samples, six environmental water samples and one synthetic sample; the results were compared with those determined by the HPLC method. The recoveries and the relative errors were 83.5–101.2 and 0.47–2.02%, respectively. The possible reaction mechanism has also been discussed. Copyright © 2009 John Wiley & Sons, Ltd.
- 17 March 2009
- Published by Wiley in Luminescence
- Vol. 24 (4) , 266-270
A novel inhibitory kinetic fluorimetric method for the determination of trace methomyl in environmental samples
A novel inhibitory kinetic fluorimetric method for the determination of trace methomyl was proposed. It was shown that the Fenton reagent oxidized rhodamine B in acid medium which enabled the fluorescence quenching of the latter. The presence of trace methomyl clearly inhibited the reaction. Upon addition of EDTA, a good linear relationship between the inhibitory effect and the concentration of methomyl was observed, together with improved stabilization and sensitivity. Factors affecting the determination of trace methomyl were investigated systematically. Under the optimum conditions, the linear range for the determination of methomyl was 0.04–2.2 µg/mL; the detection limit and the quantification limit for methomyl were 0.011 and 0.037 µg/mL, respectively. The proposed method was applied to the determination of methomyl in four environmental soil samples, six environmental water samples and one synthetic sample; the results were compared with those determined by the HPLC method. The recoveries and the relative errors were 83.5–101.2 and 0.47–2.02%, respectively. The possible reaction mechanism has also been discussed. Copyright © 2009 John Wiley & Sons, Ltd.
- 17 October 2008
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 47 (22) , 8550-8554
Reduction of Nitrite by Ultrasound-Dispersed Nanoscale Zero-Valent Iron Particles
- 17 October 2008
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 47 (22) , 8550-8554
Reduction of Nitrite by Ultrasound-Dispersed Nanoscale Zero-Valent Iron Particles