Milena Špírková
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Milena Špírková has a total of 86 co-authors. Here are the top co-authors by number of shared publications:
Jiří Hodan
Institute of Macromolecular Chemistry CAS Prague Czech Republic
7 shared publications- Jiří Brus
Institute of Macromolecular Chemistry, Czech Academy of Sciences
6 shared publications - Miroslav Šlouf
Institute of Macromolecular Chemistry, Czech Academy of Sciences, CZ-16206 Prague, Czech Republic
6 shared publications - Rafał Poręba
Institute of Macromolecular Chemistry AS CR v.v.i., Heyrovského nám. 2, 162 06 Praha 6 Czech Republic
6 shared publications Adam Strachota
Nanostructured Polymers and Composites Department, Institute of Macromolecular Chemistry AS CR v.v.i, (IMC), Heyrovsky Sq. 2, Prague 162 06, Czech Republic
5 shared publicationsJana Kredatusová
Institute of Macromolecular Chemistry AS CR Heyrovského nám. 2, 162 06 Prague 6 Czech Republic
5 shared publications
Latest Publications
- 1 January 2024
- Published by University Library in Kragujevac
- p. 592-595
Mechanical Properties of Hybrid Materials Based on Aliphatic Polyurethanes and Al₂O₃ Nanoparticles
In this research, hybrid materials based on aliphatic polyurethanes and hydrophilic aluminum(III) oxide nanoparticles were synthesized. From an environmental point of view, synthesized hybrid materials represent significant engineering materials because the products of their thermal degradation are significantly less toxic compared to the products of thermal decomposition of polyurethane, for which production aromatic isocyanates are used. The presence of uniformly distributed Al2O3 nanoparticles in the sample containing 0.5 wt. % of inorganic filler influenced the additional formation of hydrogen bonds, as well as the improvement of the mechanical properties of the obtained polyurethane hybrid materials. Good mechanical properties, together with appropriate properties of thermal stability, allow the obtained hybrid materials based on aliphatic polyurethanes and Al2O3 inorganic filler to be used in the automotive industry (hydraulic seals, protective films), furniture and in the production of sports equipment.
- 1 January 2024
- Published by University Library in Kragujevac
- p. 592-595
Mechanical Properties of Hybrid Materials Based on Aliphatic Polyurethanes and Al₂O₃ Nanoparticles
In this research, hybrid materials based on aliphatic polyurethanes and hydrophilic aluminum(III) oxide nanoparticles were synthesized. From an environmental point of view, synthesized hybrid materials represent significant engineering materials because the products of their thermal degradation are significantly less toxic compared to the products of thermal decomposition of polyurethane, for which production aromatic isocyanates are used. The presence of uniformly distributed Al2O3 nanoparticles in the sample containing 0.5 wt. % of inorganic filler influenced the additional formation of hydrogen bonds, as well as the improvement of the mechanical properties of the obtained polyurethane hybrid materials. Good mechanical properties, together with appropriate properties of thermal stability, allow the obtained hybrid materials based on aliphatic polyurethanes and Al2O3 inorganic filler to be used in the automotive industry (hydraulic seals, protective films), furniture and in the production of sports equipment.
- Open Access
Morphology, Micromechanical, and Macromechanical Properties of Novel Waterborne Poly(urethane-urea)/Silica Nanocomposites
Morphology, macro-, and micromechanical properties of novel poly(urethane-urea)/silica nanocomposites were analyzed by electron microscopy, dynamic mechanical thermal analysis, and microindentation. The studied nanocomposites were based on a poly(urethane-urea) (PUU) matrix filled by nanosilica, and were prepared from waterborne dispersions of PUU (latex) and SiO2. The loading of nano-SiO2 was varied between 0 (neat matrix) and 40 wt% in the dry nanocomposite. The prepared materials were all formally in the rubbery state at room temperature, but they displayed complex elastoviscoplastic behavior, spanning from stiffer elastomeric type to semi-glassy. Because of the employed rigid and highly uniform spherical nanofiller, the materials are of great interest for model microindentation studies. Additionally, because of the polycarbonate-type elastic chains of the PUU matrix, hydrogen bonding in the studied nanocomposites was expected to be rich and diverse, ranging from very strong to weak. In micro- and macromechanical tests, all the elasticity-related properties correlated very strongly. The relations among the properties that related to energy dissipation were complex, and were highly affected by the existence of hydrogen bonding of broadly varied strength, by the distribution patterns of the fine nanofiller, as well as by the eventual locally endured larger deformations during the tests, and the tendency of the materials to cold flow.
Open AccessMorphology, Micromechanical, and Macromechanical Properties of Novel Waterborne Poly(urethane-urea)/Silica Nanocomposites
Morphology, macro-, and micromechanical properties of novel poly(urethane-urea)/silica nanocomposites were analyzed by electron microscopy, dynamic mechanical thermal analysis, and microindentation. The studied nanocomposites were based on a poly(urethane-urea) (PUU) matrix filled by nanosilica, and were prepared from waterborne dispersions of PUU (latex) and SiO2. The loading of nano-SiO2 was varied between 0 (neat matrix) and 40 wt% in the dry nanocomposite. The prepared materials were all formally in the rubbery state at room temperature, but they displayed complex elastoviscoplastic behavior, spanning from stiffer elastomeric type to semi-glassy. Because of the employed rigid and highly uniform spherical nanofiller, the materials are of great interest for model microindentation studies. Additionally, because of the polycarbonate-type elastic chains of the PUU matrix, hydrogen bonding in the studied nanocomposites was expected to be rich and diverse, ranging from very strong to weak. In micro- and macromechanical tests, all the elasticity-related properties correlated very strongly. The relations among the properties that related to energy dissipation were complex, and were highly affected by the existence of hydrogen bonding of broadly varied strength, by the distribution patterns of the fine nanofiller, as well as by the eventual locally endured larger deformations during the tests, and the tendency of the materials to cold flow.
- 5 October 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 138 (11)
Mechanically strong waterborne poly(urethane‐urea) films and nanocomposite films
A series of transparent waterborne poly(urethane‐urea) (PUU) films and nanocomposite films were prepared using isocyanate excess (5–50 mol% excess relative to the hydroxyl groups) and omitting the common chain‐extension step in the acetone method of the preparation. The surplus isocyanate groups were converted into urea and eventually biuret linkages via the reaction with water during the last phase inversion step. Nanocomposites were prepared by the direct mixing of the PUU nanoparticles in water with aqueous nanosilica or montmorillonite powder followed by slow water evaporation. Variable urea/biuret content is responsible for substantially different tensile properties; the neat organic films show elongation‐at‐break values of 100%–1120%, tensile strength values of 0.07–22.1 MPa, and energy‐to‐break of 0.1–85 mJ × mm−3. All of the materials can be potentially used as soft‐to‐hard topcoats, depending on the specific demands. The most promising materials are films prepared at 30 and particularly 40 mol% isocyanate excess.
- 5 October 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 138 (11)
Mechanically strong waterborne poly(urethane‐urea) films and nanocomposite films
A series of transparent waterborne poly(urethane‐urea) (PUU) films and nanocomposite films were prepared using isocyanate excess (5–50 mol% excess relative to the hydroxyl groups) and omitting the common chain‐extension step in the acetone method of the preparation. The surplus isocyanate groups were converted into urea and eventually biuret linkages via the reaction with water during the last phase inversion step. Nanocomposites were prepared by the direct mixing of the PUU nanoparticles in water with aqueous nanosilica or montmorillonite powder followed by slow water evaporation. Variable urea/biuret content is responsible for substantially different tensile properties; the neat organic films show elongation‐at‐break values of 100%–1120%, tensile strength values of 0.07–22.1 MPa, and energy‐to‐break of 0.1–85 mJ × mm−3. All of the materials can be potentially used as soft‐to‐hard topcoats, depending on the specific demands. The most promising materials are films prepared at 30 and particularly 40 mol% isocyanate excess.
- Open Access
The Influence of Nanofiller Shape and Nature on the Functional Properties of Waterborne Poly(urethane-urea) Nanocomposite Films
A series of waterborne polycarbonate-based poly(urethane-urea) nanocomposite films were prepared and characterized. An isocyanate excess of 30 mol% with respect to the hydroxyl groups was used in the procedure, omitting the chain-extension step of the acetone process in the dispersion preparation. The individual steps of the synthesis of the poly(urethane-urea) matrix were followed by nuclear magnetic resonance (NMR) spectroscopy. The nanofillers (1 wt% in the final nanocomposite) differed in nature and shape. Starch, graphene oxide and nanocellulose were used as representatives of organic nanofillers, while halloysite, montmorillonite, nanosilica and hydroxyapatite were used as representatives of inorganic nanofillers. Moreover, the fillers differed in their shape and average particle size. The films were characterized by a set of methods to obtain the tensile, thermal and surface properties of the nanocomposites as well as the internal arrangement of the nanoparticles in the nanocomposite film. The degradation process was evaluated at 37 °C in a H2O2 + CoCl2 solution.
Open AccessThe Influence of Nanofiller Shape and Nature on the Functional Properties of Waterborne Poly(urethane-urea) Nanocomposite Films
A series of waterborne polycarbonate-based poly(urethane-urea) nanocomposite films were prepared and characterized. An isocyanate excess of 30 mol% with respect to the hydroxyl groups was used in the procedure, omitting the chain-extension step of the acetone process in the dispersion preparation. The individual steps of the synthesis of the poly(urethane-urea) matrix were followed by nuclear magnetic resonance (NMR) spectroscopy. The nanofillers (1 wt% in the final nanocomposite) differed in nature and shape. Starch, graphene oxide and nanocellulose were used as representatives of organic nanofillers, while halloysite, montmorillonite, nanosilica and hydroxyapatite were used as representatives of inorganic nanofillers. Moreover, the fillers differed in their shape and average particle size. The films were characterized by a set of methods to obtain the tensile, thermal and surface properties of the nanocomposites as well as the internal arrangement of the nanoparticles in the nanocomposite film. The degradation process was evaluated at 37 °C in a H2O2 + CoCl2 solution.
- 19 June 2020
- Published by Wiley in Polymer Composites
- Vol. 41 (10) , 4031-4042
Novel waterborne poly(urethane‐urea)/silica nanocomposites
A series of novel transparent mechanically strong waterborne poly(urethane‐urea)/silica nanocomposites were prepared by mixing a waterborne poly(urethane‐urea) dispersion with aqueous nanosilica, followed by slow water evaporation. This procedure is simple, environmentally friendly and energetically undemanding. The silica content in the nanocomposite film varied from 0 to 50 wt%. Based on changes of tensile characteristics, for example, Young's modulus values, three types of behavior were observed: typical elastic (0‐10 wt%), plastic (30 wt%) and ceramic‐like (50 wt% silica) materials can be prepared. However, some films feature both elastic and plastic (material with 20 wt% silica) or plastic and ceramic‐like characteristics (material with 40 wt% silica). The Young's modulus varied from 6 to 705 MPa, and the maximal tensile strength and elongation‐at‐break were 17.3 MPa and 1270%, respectively. The maximum energy‐to‐break, 60 mJ mm−3, was achieved for the film containing 30 wt% silica. All these materials can potentially be used as soft‐to‐hard topcoats, depending on the specific demands.
- 19 June 2020
- Published by Wiley in Polymer Composites
- Vol. 41 (10) , 4031-4042
Novel waterborne poly(urethane‐urea)/silica nanocomposites
A series of novel transparent mechanically strong waterborne poly(urethane‐urea)/silica nanocomposites were prepared by mixing a waterborne poly(urethane‐urea) dispersion with aqueous nanosilica, followed by slow water evaporation. This procedure is simple, environmentally friendly and energetically undemanding. The silica content in the nanocomposite film varied from 0 to 50 wt%. Based on changes of tensile characteristics, for example, Young's modulus values, three types of behavior were observed: typical elastic (0‐10 wt%), plastic (30 wt%) and ceramic‐like (50 wt% silica) materials can be prepared. However, some films feature both elastic and plastic (material with 20 wt% silica) or plastic and ceramic‐like characteristics (material with 40 wt% silica). The Young's modulus varied from 6 to 705 MPa, and the maximal tensile strength and elongation‐at‐break were 17.3 MPa and 1270%, respectively. The maximum energy‐to‐break, 60 mJ mm−3, was achieved for the film containing 30 wt% silica. All these materials can potentially be used as soft‐to‐hard topcoats, depending on the specific demands.
- 13 April 2019
- Published by Wiley in Polymer Composites
- Vol. 40 (10) , 4079-4092
Recyclable polyurethane/nanoclay films
A series of polyurethane (PU)/clay nanocomposite films was prepared by adding natural bentonite Cloisite® Na+ powders to waterborne polyurethane dispersions (PUDs) followed by a slow water evaporation; the nanoclay content in the films varied from 0 to 5 wt%. The functional properties of materials with low nanoclay loading (up to 1 wt%) resemble features of films prepared without any nanoclay. Compared to unfilled PU, the films with 3 and 5 wt% nanoclay concentrations exhibited slightly deteriorated properties. This phenomenon can be caused by the fact that the polymer–filler interactions are negligible. Gas transport properties are the exception: nanoclay was found to be an efficient barrier component for the permeability of industrially important gases (O2, N2, H2, CO2, and CH4). All films feature thermoplastic characteristics and thermal stabilities up to at least 200°C. Because PUDs are solely composed of linear chains, the possibility of preparing recyclable materials was tested. While PU can be re‐used after dissolving in acetone and re‐dispersing in water, the re‐use of nanoclay is not recommended. Preliminary accelerated in vivo tests performed in 20% H2O2 and 0.1M CoCl2 at 37°C detected substantial susceptibility to biodegradation, especially for films containing 5 wt% nanoclay. POLYM. COMPOS., 40:4079–4092, 2019. © 2019 Society of Plastics Engineers
- 13 April 2019
- Published by Wiley in Polymer Composites
- Vol. 40 (10) , 4079-4092
Recyclable polyurethane/nanoclay films
A series of polyurethane (PU)/clay nanocomposite films was prepared by adding natural bentonite Cloisite® Na+ powders to waterborne polyurethane dispersions (PUDs) followed by a slow water evaporation; the nanoclay content in the films varied from 0 to 5 wt%. The functional properties of materials with low nanoclay loading (up to 1 wt%) resemble features of films prepared without any nanoclay. Compared to unfilled PU, the films with 3 and 5 wt% nanoclay concentrations exhibited slightly deteriorated properties. This phenomenon can be caused by the fact that the polymer–filler interactions are negligible. Gas transport properties are the exception: nanoclay was found to be an efficient barrier component for the permeability of industrially important gases (O2, N2, H2, CO2, and CH4). All films feature thermoplastic characteristics and thermal stabilities up to at least 200°C. Because PUDs are solely composed of linear chains, the possibility of preparing recyclable materials was tested. While PU can be re‐used after dissolving in acetone and re‐dispersing in water, the re‐use of nanoclay is not recommended. Preliminary accelerated in vivo tests performed in 20% H2O2 and 0.1M CoCl2 at 37°C detected substantial susceptibility to biodegradation, especially for films containing 5 wt% nanoclay. POLYM. COMPOS., 40:4079–4092, 2019. © 2019 Society of Plastics Engineers
- 21 December 2016
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 128 (3) , 1699-1709
The impact of conditions mimicking physiological environment on the thermal stability of aliphatic polycarbonate-based polyurethane elastomers
- 21 December 2016
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 128 (3) , 1699-1709
The impact of conditions mimicking physiological environment on the thermal stability of aliphatic polycarbonate-based polyurethane elastomers
- 26 October 2015
- Published by Taylor & Francis in Composite Interfaces
- Vol. 23 (2) , 157-173
Organic–inorganic nanocomposite films made from polyurethane dispersions and colloidal silica particles
Polyurethane/silica nanocomposites were prepared by solution blending of polyurethane water dispersion (PUD) based on polycarbonate macrodiol with colloidal silica aqueous sol LUDOX TMA. Because of mixing PUDs made from linear polyurethane with the nanofiller, only physical polymer/filler type of interface formed by hydrogen bonds was obtained. As a result the materials were possible to reuse after dissolution in acetone followed by dispersion in water. The effect of colloidal silica content on mechanical, thermal, morphological, and swelling properties of obtained films was tested by tensile test, dynamic mechanical thermal analysis, thermogravimertic analysis, scanning electron microscopy, atomic force microscopy, and swelling analyses. The nanocomposites were classified in three groups differing in the internal structure and functional properties: organic matrix filled with inorganic nanofiller (up to 10 wt% of silica), bicontinous systems (25 and 32 wt% of silica) and inorganic matrix filled with polyurethane (50 and 60 wt% of silica). Only small amount of colloidal silica (up to 10 wt%) improves thermo-mechanical properties, smoothes the materials, and suppresses extent of swelling without changing of the films transparency.
- 26 October 2015
- Published by Taylor & Francis in Composite Interfaces
- Vol. 23 (2) , 157-173
Organic–inorganic nanocomposite films made from polyurethane dispersions and colloidal silica particles
Polyurethane/silica nanocomposites were prepared by solution blending of polyurethane water dispersion (PUD) based on polycarbonate macrodiol with colloidal silica aqueous sol LUDOX TMA. Because of mixing PUDs made from linear polyurethane with the nanofiller, only physical polymer/filler type of interface formed by hydrogen bonds was obtained. As a result the materials were possible to reuse after dissolution in acetone followed by dispersion in water. The effect of colloidal silica content on mechanical, thermal, morphological, and swelling properties of obtained films was tested by tensile test, dynamic mechanical thermal analysis, thermogravimertic analysis, scanning electron microscopy, atomic force microscopy, and swelling analyses. The nanocomposites were classified in three groups differing in the internal structure and functional properties: organic matrix filled with inorganic nanofiller (up to 10 wt% of silica), bicontinous systems (25 and 32 wt% of silica) and inorganic matrix filled with polyurethane (50 and 60 wt% of silica). Only small amount of colloidal silica (up to 10 wt%) improves thermo-mechanical properties, smoothes the materials, and suppresses extent of swelling without changing of the films transparency.
- 16 July 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (42)
Preparation and characterization of thermoplastic water‐borne polycarbonate‐based polyurethane dispersions and cast films
Stable water‐borne polyurethane dispersions (PUDs) were prepared from bifunctional aliphatic polycarbonate‐based macrodiol, 2,2‐bis(hydroxymethyl)propionic acid (DMPA), 1,6‐diisocyanatohexane, 1,4‐butanediol (BD), and triethylamine. Water‐borne dispersion particles are thus solely formed from self‐assembled linear PU chains. Both PUDs and PUD‐based films were characterized with regards to the concentration of DMPA (ionic species content) and BD (hard‐segment content). Average particle size of PUDs decreased and their long‐term stability increased with increasing DMPA and decreasing BD concentration. Functional properties of cast films made from PUDs are substantially influenced by the character of the original colloidal particle dispersions. The swelling behavior of the films, their surface morphology, and mechanical properties are more influenced by DMPA than BD contents. At DMPA concentrations higher than 0.2 mmol g−1of the solid mass of polyurethane, distinct self‐organization of individual nanoparticles into fibril‐like structures was detected by atomic force microscopy and scanning electron microscopy. PU films made from PUD containing high BD as well as high DMPA concentrations have the best utility properties namely sufficient tensile properties and a very low swelling ability. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci.2015,132, 42672.
- 16 July 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (42)
Preparation and characterization of thermoplastic water‐borne polycarbonate‐based polyurethane dispersions and cast films
Stable water‐borne polyurethane dispersions (PUDs) were prepared from bifunctional aliphatic polycarbonate‐based macrodiol, 2,2‐bis(hydroxymethyl)propionic acid (DMPA), 1,6‐diisocyanatohexane, 1,4‐butanediol (BD), and triethylamine. Water‐borne dispersion particles are thus solely formed from self‐assembled linear PU chains. Both PUDs and PUD‐based films were characterized with regards to the concentration of DMPA (ionic species content) and BD (hard‐segment content). Average particle size of PUDs decreased and their long‐term stability increased with increasing DMPA and decreasing BD concentration. Functional properties of cast films made from PUDs are substantially influenced by the character of the original colloidal particle dispersions. The swelling behavior of the films, their surface morphology, and mechanical properties are more influenced by DMPA than BD contents. At DMPA concentrations higher than 0.2 mmol g−1of the solid mass of polyurethane, distinct self‐organization of individual nanoparticles into fibril‐like structures was detected by atomic force microscopy and scanning electron microscopy. PU films made from PUD containing high BD as well as high DMPA concentrations have the best utility properties namely sufficient tensile properties and a very low swelling ability. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci.2015,132, 42672.
- 7 January 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (16)
Thermal and mechanical properties of multiple‐component aliphatic degradable polyurethanes
Macroscopic thermal and mechanical properties of complex aliphatic polycarbonate‐based polyurethane (PU) films containing degradable ester units in PU backbone were studied by a combination of several experimental techniques. Differential scanning calorimetry (DSC) revealed that the synthesized oligomeric diol (DL‐L) contributes (in addition to polycarbonate diol) to the formation of soft‐segment domains, while the hard‐segment domains are formed from 1,6‐diisocyanatohexane (HDI) and butane‐1,4‐diol (BD). Three main phase transitions were detected by DSC and by dynamic mechanical thermal analysis. Thermogravimetric analysis (TGA) of two‐component PUs showed that the PU made from DL‐L and HDI is the least thermostable product, while the PU made from polycarbonate diol and HDI is the most stable one. The differences in the thermal stability of different four‐component PUs are not important. Tensile properties very sensitively reflect the changes in composition and in microstructure of PU samples; the best tensile properties exhibits the degradable sample containing the equimolar ratio of hydroxyl groups of macrodiol, oligomeric diol DL‐L and butane‐1,4‐diol. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 41872.
- 7 January 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (16)
Thermal and mechanical properties of multiple‐component aliphatic degradable polyurethanes
Macroscopic thermal and mechanical properties of complex aliphatic polycarbonate‐based polyurethane (PU) films containing degradable ester units in PU backbone were studied by a combination of several experimental techniques. Differential scanning calorimetry (DSC) revealed that the synthesized oligomeric diol (DL‐L) contributes (in addition to polycarbonate diol) to the formation of soft‐segment domains, while the hard‐segment domains are formed from 1,6‐diisocyanatohexane (HDI) and butane‐1,4‐diol (BD). Three main phase transitions were detected by DSC and by dynamic mechanical thermal analysis. Thermogravimetric analysis (TGA) of two‐component PUs showed that the PU made from DL‐L and HDI is the least thermostable product, while the PU made from polycarbonate diol and HDI is the most stable one. The differences in the thermal stability of different four‐component PUs are not important. Tensile properties very sensitively reflect the changes in composition and in microstructure of PU samples; the best tensile properties exhibits the degradable sample containing the equimolar ratio of hydroxyl groups of macrodiol, oligomeric diol DL‐L and butane‐1,4‐diol. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 41872.