Xiaoyang Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiaoyang Huang has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Chun Yang
School of Mechanical and Aerospace Engineering Nanyang Technological University Singapore Singapore
5 shared publications - Nam-Trung Nguyen
Queensland Quantum and Advanced Technologies Research Institute, Griffith University, 170 Kessels Road, Nathan, QLD 4111, Australia
3 shared publications - Chih-Yung Wen
The Hong Kong Polytechnic University
1 shared publication H. Min
Nanyang Technological University
1 shared publicationH.Y Zhang
School of Mechanical and Production Engineering, Nanyang Technological University, Nanyang Avenue, Singapore 639798, Singapore
1 shared publicationKon Meng Ng
Nanyang Technological Univ. (Singapore)
1 shared publication
Latest Publications
- Open Access
- 28 January 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (2) , 203
Investigation of the Dynamics of Cavitation Bubbles in a Microfluidic Channel with Actuations
This work presents experimental and numerical studies on the dynamics of cavitation bubbles in a nozzle-shaped microfluidic channel with PZT (lead-zirconate-titanate) actuations. It is found that a cloud of bubbles can be generated near the center of the microfluidic channel when the actuation voltage is larger than a threshold at 1 kHz. After being generated, the bubbles under actuations oscillate radially with violent expansion and compression, and simultaneously translate upstream towards the opening of the nozzle. Along with radial oscillation and translation, the bubbles undergo frequent and drastic coalescence and breakup, leading to vigorous churning of surrounding liquids. The pressure variation and distribution in the microchannel are calculated by numerical simulation in Ansys Fluent, and results show that there is a low-pressure zone inside the microfluidic channel within each cycle of the actuation period, which is responsible for bubble generation observed in the experiments. The method of bubble generation in this study is novel and can be applied for the enhancement of heat and mass transfer in microfluidic operations.
- 28 January 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (2) , 203
Open AccessInvestigation of the Dynamics of Cavitation Bubbles in a Microfluidic Channel with Actuations
This work presents experimental and numerical studies on the dynamics of cavitation bubbles in a nozzle-shaped microfluidic channel with PZT (lead-zirconate-titanate) actuations. It is found that a cloud of bubbles can be generated near the center of the microfluidic channel when the actuation voltage is larger than a threshold at 1 kHz. After being generated, the bubbles under actuations oscillate radially with violent expansion and compression, and simultaneously translate upstream towards the opening of the nozzle. Along with radial oscillation and translation, the bubbles undergo frequent and drastic coalescence and breakup, leading to vigorous churning of surrounding liquids. The pressure variation and distribution in the microchannel are calculated by numerical simulation in Ansys Fluent, and results show that there is a low-pressure zone inside the microfluidic channel within each cycle of the actuation period, which is responsible for bubble generation observed in the experiments. The method of bubble generation in this study is novel and can be applied for the enhancement of heat and mass transfer in microfluidic operations.
- 16 August 2017
- Published by Wiley in Journal of Heat Transfer
- Vol. 140 (1)
Hydrodynamic Effects on Particle Deposition in Microchannel Flows at Elevated Temperatures
Particulate fouling and particle deposition at elevated temperature are crucial issues in microchannel heat exchangers. In this work, a microfluidic system was designed to examine the hydrodynamic effects on the deposition of microparticles in a microchannel flow, which simulate particle deposits in microscale heat exchangers. The deposition rates of microparticles were measured in two typical types of flow, a steady flow and a pulsatile flow. Under a given elevated solution temperature and electrolyte concentration of the particle dispersion in the tested flow rate range, the dimensionless particle deposition rate (Sherwood number) was found to decrease with the Reynolds number of the steady flow and reach a plateau for the Reynolds number beyond 0.091. Based on the Derjaguin–Landau–Verwey–Overbeek (DLVO) theory, a mass transport model was developed with considering temperature dependence of the particle deposition at elevated temperatures. The modeling results can reasonably capture our experimental observations. Moreover, the experimental results of the pulsatile flow revealed that the particle deposition rate in the microchannel can be mitigated by increasing the frequency of pulsation within a low-frequency region. Our findings are expected to provide a better understanding of thermally driven particulate fouling as well as to provide useful information for design and operation of microchannel heat exchangers.
- 16 August 2017
- Published by Wiley in Journal of Heat Transfer
- Vol. 140 (1)
Hydrodynamic Effects on Particle Deposition in Microchannel Flows at Elevated Temperatures
Particulate fouling and particle deposition at elevated temperature are crucial issues in microchannel heat exchangers. In this work, a microfluidic system was designed to examine the hydrodynamic effects on the deposition of microparticles in a microchannel flow, which simulate particle deposits in microscale heat exchangers. The deposition rates of microparticles were measured in two typical types of flow, a steady flow and a pulsatile flow. Under a given elevated solution temperature and electrolyte concentration of the particle dispersion in the tested flow rate range, the dimensionless particle deposition rate (Sherwood number) was found to decrease with the Reynolds number of the steady flow and reach a plateau for the Reynolds number beyond 0.091. Based on the Derjaguin–Landau–Verwey–Overbeek (DLVO) theory, a mass transport model was developed with considering temperature dependence of the particle deposition at elevated temperatures. The modeling results can reasonably capture our experimental observations. Moreover, the experimental results of the pulsatile flow revealed that the particle deposition rate in the microchannel can be mitigated by increasing the frequency of pulsation within a low-frequency region. Our findings are expected to provide a better understanding of thermally driven particulate fouling as well as to provide useful information for design and operation of microchannel heat exchangers.
- 6 January 2016
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 20 (1) , 1-13
Bubble dynamics in a microfluidic chamber under low-frequency actuation
- 6 January 2016
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 20 (1) , 1-13
Bubble dynamics in a microfluidic chamber under low-frequency actuation
- 3 June 2014
- Published by Springer Nature in Experiments in Fluids
- Vol. 55 (6) , 1-6
Vortex generation in a microfluidic chamber with actuations
- 3 June 2014
- Published by Springer Nature in Experiments in Fluids
- Vol. 55 (6) , 1-6
Vortex generation in a microfluidic chamber with actuations
- 13 November 2013
- Published by Springer Nature
- p. 405-411
Feedback Control of Flow-Induced Vibrations on Head Gimbals Assembly Inside Hard Disk Drives
- 13 November 2013
- Published by Springer Nature
- p. 405-411
Feedback Control of Flow-Induced Vibrations on Head Gimbals Assembly Inside Hard Disk Drives
- 5 May 2011
- Published by Royal Society of Chemistry (RSC) in Lab on a Chip
- Vol. 11 (12) , 2081-2087
Mixing enhancement for high viscous fluids in a microfluidic chamber
Due to small channel dimensions and laminar flows, mixing in microfluidic systems is always a challenging task, especially for high viscous fluids. Here we report a method of enhancing microfluidic mixing for high viscous fluids using acoustically induced bubbles. The bubbles can be generated in an acoustically profiled microfluidic structure by using a piezoelectric disk activated at a working frequency range between 1.5 kHz and 2 kHz. The mixing enhancement is achieved through interactions between the oscillating bubbles and fluids. Both experimental studies and numerical simulations are conducted. In the experiments, DI water–glycerol mixture solutions with various viscosities were used. The results, based on the mixing efficiency calculated from experimentally acquired fluorescent images, showed that good mixing can occur in the DI water–glycerol solutions with their maximum viscosity up to 44.75 mPa s, which to our best knowledge is the highest viscosity of fluids in microfluidic mixing experiments. To explain the mechanisms of bubble generation, the numerical simulation results show that, corresponding to the actuations at the working frequency range used in the experiment, there exists a low pressure region where the pressure is lower than the water vapor pressure in the DI water–glycerol solutions, resulting in the generation of bubbles.
- 5 May 2011
- Published by Royal Society of Chemistry (RSC) in Lab on a Chip
- Vol. 11 (12) , 2081-2087
Mixing enhancement for high viscous fluids in a microfluidic chamber
Due to small channel dimensions and laminar flows, mixing in microfluidic systems is always a challenging task, especially for high viscous fluids. Here we report a method of enhancing microfluidic mixing for high viscous fluids using acoustically induced bubbles. The bubbles can be generated in an acoustically profiled microfluidic structure by using a piezoelectric disk activated at a working frequency range between 1.5 kHz and 2 kHz. The mixing enhancement is achieved through interactions between the oscillating bubbles and fluids. Both experimental studies and numerical simulations are conducted. In the experiments, DI water–glycerol mixture solutions with various viscosities were used. The results, based on the mixing efficiency calculated from experimentally acquired fluorescent images, showed that good mixing can occur in the DI water–glycerol solutions with their maximum viscosity up to 44.75 mPa s, which to our best knowledge is the highest viscosity of fluids in microfluidic mixing experiments. To explain the mechanisms of bubble generation, the numerical simulation results show that, corresponding to the actuations at the working frequency range used in the experiment, there exists a low pressure region where the pressure is lower than the water vapor pressure in the DI water–glycerol solutions, resulting in the generation of bubbles.
- 21 November 2009
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 8 (4) , 549-555
Valveless micropump with acoustically featured pumping chamber
- 21 November 2009
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 8 (4) , 549-555
Valveless micropump with acoustically featured pumping chamber
- 8 September 2009
- Published by Elsevier in Applied Acoustics
- Vol. 71 (2) , 164-168
A standing wave model for acoustic pumping effect in microchannels
- 8 September 2009
- Published by Elsevier in Applied Acoustics
- Vol. 71 (2) , 164-168
A standing wave model for acoustic pumping effect in microchannels
- 6 November 2007
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 5 (2) , 205-214
Thermocapillary actuation of droplet in a planar microchannel
- 6 November 2007
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 5 (2) , 205-214
Thermocapillary actuation of droplet in a planar microchannel
- 1 July 2007
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 122 (1) , 38-41
Nonlinear standing waves in a resonator with feedback control
An experimental study is presented to demonstrate that nonlinear effect on standing waves in a resonator can be reduced by a feedback loop responding to the second harmonic. The resonator was a cylindrical tube sealed at one end and driven by a horn driver unit at another end. The feedback control loop consisted of a pressure sensor, a frequency filter, a phase shifter, and an actuator. The results show that the waveform distortions can be eliminated and large amplitude sinusoidal pressure oscillations are obtained. A simple model is proposed for a qualitative discussion on the control mechanism, which shows that the feedback loop alters the imaginary part of the complex mode frequency so as to suppress (or enhance) the second harmonic.
- 1 July 2007
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 122 (1) , 38-41
Nonlinear standing waves in a resonator with feedback control
An experimental study is presented to demonstrate that nonlinear effect on standing waves in a resonator can be reduced by a feedback loop responding to the second harmonic. The resonator was a cylindrical tube sealed at one end and driven by a horn driver unit at another end. The feedback control loop consisted of a pressure sensor, a frequency filter, a phase shifter, and an actuator. The results show that the waveform distortions can be eliminated and large amplitude sinusoidal pressure oscillations are obtained. A simple model is proposed for a qualitative discussion on the control mechanism, which shows that the feedback loop alters the imaginary part of the complex mode frequency so as to suppress (or enhance) the second harmonic.