Andreas Boger
Andreas Boger has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Bernhard Rieger
Wacker-Chair of Macromolecular Chemistry, Department of Chemistry, TUM School of Natural Sciences, Technical University of Munich, Lichtenbergstraße 4, 85748 Garching, Germany
2 shared publications - Carsten Troll
WACKER-Lehrstuhl für Makromolekulare Chemie, Technische Universität München, Lichtenbergstraße 4, 85747 Garching bei München, Germany
2 shared publications Erich Schneider
AO Research Institute, Clavadelerstrasse 8, 7270 Davos Platz, Switzerland
2 shared publicationsKurtis Wheeler
R&D Biomaterials, Synthes GmbH, Eimattstrasse 3, 4436 Oberdorf, Switzerland
2 shared publications- Marc Bohner
RMS Foundation, Robert Mathys Strasse 1, CH-2544 Bettlach, Switzerland
2 shared publications Paul Heini
Orthopedic Surgery, University of Berne, Inselspital, 3010 Bern, Switzerland
2 shared publications
Latest Publications
- Open Access
- 6 July 2011
- Published by Hindawi Limited in ISRN Materials Science
- Vol. 2011, 1-7
A Medium Viscous Acrylic Cement Enhances Uniformity of Cement Filling and Reduces Leakage in Cancellous Bone Augmentation
Vertebroplasty is an efficient procedure to treat osteoporotic vertebral fractures. Cement leakage is considered to be the most severe complication during vertebroplasty. At high cement viscosities, the risk of leakage is reduced. However, injection forces are highly increased, requiring the use of high force injection systems with the lack in tactile force feedback. Therefore, an acrylic cement was developed showing medium initial viscosity and which still allows to be manually applied using syringes. An established model favoring leakage was used to observe the filling pattern and leaked cement mass. The method used included the simulation of body temperature, and all materials submitted are approved medical products. When applied just after preparation, the medium viscous cement resulted in good cement filling and less cement leakage than low viscosity cement. The added clinical value of the new cement is that the waiting time for the physician will be shortened to zero minutes without compromising the safety for the procedure.
- 6 July 2011
- Published by Hindawi Limited in ISRN Materials Science
- Vol. 2011, 1-7
Open AccessA Medium Viscous Acrylic Cement Enhances Uniformity of Cement Filling and Reduces Leakage in Cancellous Bone Augmentation
Vertebroplasty is an efficient procedure to treat osteoporotic vertebral fractures. Cement leakage is considered to be the most severe complication during vertebroplasty. At high cement viscosities, the risk of leakage is reduced. However, injection forces are highly increased, requiring the use of high force injection systems with the lack in tactile force feedback. Therefore, an acrylic cement was developed showing medium initial viscosity and which still allows to be manually applied using syringes. An established model favoring leakage was used to observe the filling pattern and leaked cement mass. The method used included the simulation of body temperature, and all materials submitted are approved medical products. When applied just after preparation, the medium viscous cement resulted in good cement filling and less cement leakage than low viscosity cement. The added clinical value of the new cement is that the waiting time for the physician will be shortened to zero minutes without compromising the safety for the procedure.
- 11 March 2009
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 90B (2) , 760-766
NMP‐modified PMMA bone cement with adapted mechanical and hardening properties for the use in cancellous bone augmentation
The use of polymethylmethacrylate (PMMA) to reinforce vertebral bodies (Vertebroplasty) leads to an increase in the Young's modulus of the augmented vertebral body. Fractures in the adjacent vertebrae may be the consequence thereof. Hence, PMMA with a reduced Young's modulus may be suitable for vertebroplasty. The goal of this study was to produce and characterize stiffness‐adapted PMMA cements. Modified PMMA bone cements were produced by adding N‐methyl‐pyrrolidone (NMP). Young's modulus, yield strength, polymerization temperature, setting time, and hardening behavior of different cements were analyzed. Focus was on the mechanical properties of the material after different storage conditions (in air at room temperature and in PBS at 37°C). The Young's modulus decreased from 2670 MPa (air)/2384 MPa (PBS) for the regular cement to 76 MPa (air)/320 MPa (PBS) for a material composition with 60% of the MMA substituted by NMP. Yield strength decreased from 85 MPa (air)/78 MPa (PBS) to 2 MPa (air)/24 MPa (PBS) between the regular cement and the 60% composition. Polymerization temperature decreased from 70°C (regular cement) to 48°C for the 30% composition. The hardening behavior exhibited an extension in handling time up to 200% by the modification presented. Modification of PMMA cement using NMP seems to be a promising method to make the PMMA cement more compliant for the use in cancellous bone augmentation in osteoporotic patients: adjustment of its mechanical properties close to those of cancellous bone, lower polymerization temperature, and extended handling time. © 2009 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 2009
- 11 March 2009
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 90B (2) , 760-766
NMP‐modified PMMA bone cement with adapted mechanical and hardening properties for the use in cancellous bone augmentation
The use of polymethylmethacrylate (PMMA) to reinforce vertebral bodies (Vertebroplasty) leads to an increase in the Young's modulus of the augmented vertebral body. Fractures in the adjacent vertebrae may be the consequence thereof. Hence, PMMA with a reduced Young's modulus may be suitable for vertebroplasty. The goal of this study was to produce and characterize stiffness‐adapted PMMA cements. Modified PMMA bone cements were produced by adding N‐methyl‐pyrrolidone (NMP). Young's modulus, yield strength, polymerization temperature, setting time, and hardening behavior of different cements were analyzed. Focus was on the mechanical properties of the material after different storage conditions (in air at room temperature and in PBS at 37°C). The Young's modulus decreased from 2670 MPa (air)/2384 MPa (PBS) for the regular cement to 76 MPa (air)/320 MPa (PBS) for a material composition with 60% of the MMA substituted by NMP. Yield strength decreased from 85 MPa (air)/78 MPa (PBS) to 2 MPa (air)/24 MPa (PBS) between the regular cement and the 60% composition. Polymerization temperature decreased from 70°C (regular cement) to 48°C for the 30% composition. The hardening behavior exhibited an extension in handling time up to 200% by the modification presented. Modification of PMMA cement using NMP seems to be a promising method to make the PMMA cement more compliant for the use in cancellous bone augmentation in osteoporotic patients: adjustment of its mechanical properties close to those of cancellous bone, lower polymerization temperature, and extended handling time. © 2009 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 2009
- 1 January 2009
- Published by Springer Nature in Polymer Journal
- Vol. 41 (11) , 993-1004
Nucleation and Crystallization of Low Isotatic Polypropylenes with Statistically Distributed Stereoerrors
- 1 January 2009
- Published by Springer Nature in Polymer Journal
- Vol. 41 (11) , 993-1004
Nucleation and Crystallization of Low Isotatic Polypropylenes with Statistically Distributed Stereoerrors
- 22 December 2008
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 112 (1) , 188-199
Stress‐induced changes in microstructure of a low‐crystalline polypropylene investigated at uniaxial stretching
Novel asymmetric metallocene catalysts lead to low isotactic polypropylenes (iPP) with randomly distributed stereo irregularities. The polypropylenes are low crystalline and show elastic mechanical behavior due to physical crosslinking. The morphology of such iPP, which is responsible for the observed mechanical properties, is still sparsely resolved. In the present work a low isotactic, low crystalline metallocene iPP containing randomly distributed stereoerrors was investigated. The influence of the chain microstructure in the elastic properties was studied using two complementary investigation methods, X‐ray diffraction and scanning force microscopy (SFM). For a better understanding of the unique mechanical properties, microscopic changes in morphology and strain‐induced variation in chain orientation were monitored during uniaxial stretching using SFM and wide angle X‐ray scattering measurements. For quantitative analysis and discussion the polymer chain orientations were calculated. The correlation between the orientation, the arrangements of the amorphous and crystalline phases observed by SFM, and the mechanical properties of the material at different elongation ratios allowed an interpretation of the macroscopic behavior on the microscopic scale. It was shown that the deformation behavior of low isotactic polypropylene with randomly distributed stereoerrors is in agreement with existing structural models, which proposed that small crystalline domains act as physical crosslinks for the amorphous matrix. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009
- 22 December 2008
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 112 (1) , 188-199
Stress‐induced changes in microstructure of a low‐crystalline polypropylene investigated at uniaxial stretching
Novel asymmetric metallocene catalysts lead to low isotactic polypropylenes (iPP) with randomly distributed stereo irregularities. The polypropylenes are low crystalline and show elastic mechanical behavior due to physical crosslinking. The morphology of such iPP, which is responsible for the observed mechanical properties, is still sparsely resolved. In the present work a low isotactic, low crystalline metallocene iPP containing randomly distributed stereoerrors was investigated. The influence of the chain microstructure in the elastic properties was studied using two complementary investigation methods, X‐ray diffraction and scanning force microscopy (SFM). For a better understanding of the unique mechanical properties, microscopic changes in morphology and strain‐induced variation in chain orientation were monitored during uniaxial stretching using SFM and wide angle X‐ray scattering measurements. For quantitative analysis and discussion the polymer chain orientations were calculated. The correlation between the orientation, the arrangements of the amorphous and crystalline phases observed by SFM, and the mechanical properties of the material at different elongation ratios allowed an interpretation of the macroscopic behavior on the microscopic scale. It was shown that the deformation behavior of low isotactic polypropylene with randomly distributed stereoerrors is in agreement with existing structural models, which proposed that small crystalline domains act as physical crosslinks for the amorphous matrix. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009
- 20 February 2008
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 86B (2) , 474-482
Properties of an injectable low modulus PMMA bone cement for osteoporotic bone
The use of polymethylmethacrylate (PMMA) cement to reinforce fragile or broken vertebral bodies (vertebroplasty) leads to extensive bone stiffening. Fractures in the adjacent vertebrae may be the consequence of this procedure. PMMA with a reduced Young's modulus may be more suitable. The goal of this study was to produce and characterize stiffness adapted PMMA bone cements. Porous PMMA bone cements were produced by combining PMMA with various volume fractions of an aqueous sodium hyaluronate solution. Porosity, Young's modulus, yield strength, polymerization temperature, setting time, viscosity, injectability, and monomer release of those porous cements were investigated. Samples presented pores with diameters in the range of 25–260 μm and porosity up to 56%. Young's modulus and yield strength decreased from 930 to 50 MPa and from 39 to 1.3 MPa between 0 and 56% porosity, respectively. The polymerization temperature decreased from 68°C (0%, regular cement) to 41°C for cement having 30% aqueous fraction. Setting time decreased from 1020 s (0%, regular cement) to 720 s for the 30% composition. Viscosity of the 30% composition (145 Pa s) was higher than the ones received from regular cement and the 45% composition (100–125 Pa s). The monomer release was in the range of 4–10 mg/mL for all porosities; showing no higher release for the porous materials. The generation of pores using an aqueous gel seems to be a promising method to make the PMMA cement more compliant and lower its mechanical properties to values close to those of cancellous bone. © 2008 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2008
- 20 February 2008
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 86B (2) , 474-482
Properties of an injectable low modulus PMMA bone cement for osteoporotic bone
The use of polymethylmethacrylate (PMMA) cement to reinforce fragile or broken vertebral bodies (vertebroplasty) leads to extensive bone stiffening. Fractures in the adjacent vertebrae may be the consequence of this procedure. PMMA with a reduced Young's modulus may be more suitable. The goal of this study was to produce and characterize stiffness adapted PMMA bone cements. Porous PMMA bone cements were produced by combining PMMA with various volume fractions of an aqueous sodium hyaluronate solution. Porosity, Young's modulus, yield strength, polymerization temperature, setting time, viscosity, injectability, and monomer release of those porous cements were investigated. Samples presented pores with diameters in the range of 25–260 μm and porosity up to 56%. Young's modulus and yield strength decreased from 930 to 50 MPa and from 39 to 1.3 MPa between 0 and 56% porosity, respectively. The polymerization temperature decreased from 68°C (0%, regular cement) to 41°C for cement having 30% aqueous fraction. Setting time decreased from 1020 s (0%, regular cement) to 720 s for the 30% composition. Viscosity of the 30% composition (145 Pa s) was higher than the ones received from regular cement and the 45% composition (100–125 Pa s). The monomer release was in the range of 4–10 mg/mL for all porosities; showing no higher release for the porous materials. The generation of pores using an aqueous gel seems to be a promising method to make the PMMA cement more compliant and lower its mechanical properties to values close to those of cancellous bone. © 2008 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2008
- 1 January 2008
- Published by Taylor & Francis in Journal of Biomaterials Science, Polymer Edition
- Vol. 19 (9) , 1125-1142
Variation of the mechanical properties of PMMA to suit osteoporotic cancellous bone
Poly(methyl methacrylate) (PMMA) is by far the most frequently used bone substitute material for vertebroplasty. However, there are serious complications, such as cement leakage and an increased fr...
- 1 January 2008
- Published by Taylor & Francis in Journal of Biomaterials Science, Polymer Edition
- Vol. 19 (9) , 1125-1142
Variation of the mechanical properties of PMMA to suit osteoporotic cancellous bone
Poly(methyl methacrylate) (PMMA) is by far the most frequently used bone substitute material for vertebroplasty. However, there are serious complications, such as cement leakage and an increased fr...