Jin-Hwe Kweon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jin-Hwe Kweon has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Jin-Ho Choi
Research Center for Aircraft Parts Technology, School of Mechanical and Aerospace Engineering, Gyeong-Sang National University Jinju, Gyeongnam, 660-701, Korea
17 shared publications Jin-Ho Choi
School of Mechanical, Aerospace and Information Engineering, Research Center for Aircraft Parts Technology, Gyeongsang National University, Jinju, Gyeongnam, 660-701, Republic of Korea
4 shared publicationsMun-Gyu Jeong
Department of Aerospace Engineering, Research Center for Aircraft Parts Technology, Gyeongsang National University, South Korea
4 shared publications- Young-Woo Nam
Graduate School of Aerospace and Mechanical Engineering, Korea Aerospace University, Goyang-si, Republic of Korea
4 shared publications - Ngoc-Trung Nguyen
Purdue University
3 shared publications Yong-Bin Park
Department of Aerospace Engineering , Research Center for Aircraft Parts Technology, Gyeongsang National University , Jinju , Gyeongnam , 660-701 , South Korea
3 shared publications
Latest Publications
- 7 October 2022
- Published by Springer Nature in International Journal of Aeronautical and Space Sciences
- Vol. 24 (2) , 419-429
Numerical Prediction of Failure Load of Scarf-Patch-Repaired CFRP Composite Using Damage Zone Model and Cohesive Zone Model
- 7 October 2022
- Published by Springer Nature in International Journal of Aeronautical and Space Sciences
- Vol. 24 (2) , 419-429
Numerical Prediction of Failure Load of Scarf-Patch-Repaired CFRP Composite Using Damage Zone Model and Cohesive Zone Model
- 3 September 2022
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 32 (5) , 657-673
Effect of hygrothermal condition on single-lab shear behavior of induction-welded CF/PEKK thermoplastic composites
This study analyzed the effects of hygrothermal conditions on the single-lap shear strength of a carbon fiber/poly-ether-ketone-ketone (CF/PEKK) thermoplastic composite material fabricated by induction welding. Specimens were exposed to an 85 °C/85% environment using a temperature and humidity chamber to identify the effect of moisture on single-lap shear strength, while their moisture saturation was assessed through weight measurement. Single-lap shear strength tests were performed on the dried and saturated specimens at 25 °C and 100 °C to 180 °C at 20 °C intervals. At 160 °C, the strength of the CF/PEKK thermoplastic composites rapidly declined to 76% (dried specimens) and 78% (moist specimens). The fracture surfaces and failure modes were analyzed using scanning electron microscopy images, which confirmed an increase in the degraded areas and naked fibers at higher testing temperatures. In addition, it was found that exposure to a moist environment changes the failure mode from fiber bundles and fiber/matrix failure to naked fiber and matrix failure owing to the reduction in interfacial adhesion properties. The findings confirmed that hygrothermal conditions directly affect the degradation of the CF/PEKK thermoplastic composites and that a rapid reduction in the single-lap shear strength occurs above Tg.
- 3 September 2022
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 32 (5) , 657-673
Effect of hygrothermal condition on single-lab shear behavior of induction-welded CF/PEKK thermoplastic composites
This study analyzed the effects of hygrothermal conditions on the single-lap shear strength of a carbon fiber/poly-ether-ketone-ketone (CF/PEKK) thermoplastic composite material fabricated by induction welding. Specimens were exposed to an 85 °C/85% environment using a temperature and humidity chamber to identify the effect of moisture on single-lap shear strength, while their moisture saturation was assessed through weight measurement. Single-lap shear strength tests were performed on the dried and saturated specimens at 25 °C and 100 °C to 180 °C at 20 °C intervals. At 160 °C, the strength of the CF/PEKK thermoplastic composites rapidly declined to 76% (dried specimens) and 78% (moist specimens). The fracture surfaces and failure modes were analyzed using scanning electron microscopy images, which confirmed an increase in the degraded areas and naked fibers at higher testing temperatures. In addition, it was found that exposure to a moist environment changes the failure mode from fiber bundles and fiber/matrix failure to naked fiber and matrix failure owing to the reduction in interfacial adhesion properties. The findings confirmed that hygrothermal conditions directly affect the degradation of the CF/PEKK thermoplastic composites and that a rapid reduction in the single-lap shear strength occurs above Tg.
- 15 July 2021
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 31 (2) , 151-172
Delamination growth in curved composite beam at elevated temperatures
Delamination failure commonly appears in composite structures, especially those with curved regions, where a relatively high through-thickness stress is generally created. This study examined the delamination growth behavior of curved composite laminates at elevated temperatures. A four-point bending test was performed at room temperature, 100°C, and 125°C, where 125°C exceeds the epoxy glass transition temperature. We found that the failure load at 100°C was 32.5% lower than that at room temperature, whereas at 125°C, the failure load decreased by 64.5%. Additionally, the delamination growth process, that is, delamination propagation, varied significantly with temperature. Finite element analyses using cohesive elements were performed to determine reasonable sets of cohesive parameters that accurately represent the delamination behavior of the beam at high temperatures. The values of the cohesive parameters were identified considering the degradation owing to high temperature. A comparison of the numerical and experimental results revealed good agreement in terms of the failure load and modes. The effect of temperature on the failure mechanism was thoroughly discussed.
- 15 July 2021
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 31 (2) , 151-172
Delamination growth in curved composite beam at elevated temperatures
Delamination failure commonly appears in composite structures, especially those with curved regions, where a relatively high through-thickness stress is generally created. This study examined the delamination growth behavior of curved composite laminates at elevated temperatures. A four-point bending test was performed at room temperature, 100°C, and 125°C, where 125°C exceeds the epoxy glass transition temperature. We found that the failure load at 100°C was 32.5% lower than that at room temperature, whereas at 125°C, the failure load decreased by 64.5%. Additionally, the delamination growth process, that is, delamination propagation, varied significantly with temperature. Finite element analyses using cohesive elements were performed to determine reasonable sets of cohesive parameters that accurately represent the delamination behavior of the beam at high temperatures. The values of the cohesive parameters were identified considering the degradation owing to high temperature. A comparison of the numerical and experimental results revealed good agreement in terms of the failure load and modes. The effect of temperature on the failure mechanism was thoroughly discussed.
- 1 January 2020
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 29 (3) , 285-300
Tensile strength of composite bonded scarf joint in various thermal environmental conditions
This study analyzed variations of tensile strength and the failure mode of composite bonded scarf joint in various thermal environments. A total of 70 scarf bonded joints were manufactured using secondary bonding and co-bonding methods, in which a number of 10 scarf joints were additionally attached to an external ply over the joint area to examine its effect. Six different environmental temperatures ranged from 25°C to 150°C were chosen and tested. A pure laminate having the same stacking sequence as the parent laminate was prepared and tested at the six temperatures for references. Experimental results revealed that tensile strengths of the secondary bonded (SB) and co-bonded (CB) joints at 75°C reduced by 9.3% and 10.5% in comparison with strengths of the corresponding joints at 25°C, respectively. Particularly, at 125°C, which is higher than the resin glass transition temperature, significant reductions of 57.1% and 53.6% in strength were found for SB and CB joints, respectively. In terms of the manufacturing methods, the strengths of the SB joints were higher than those of the CB at 25°C, 50°C, and 75°C by 6.5%, 7.6%, and 8.0%, respectively. However, at high temperatures (100°C, 125°C, and 150°C) these differences were negligible. Strengths of SB joints attached external ply increased by 5.9% and 37.5% compared to those of SB joints without the external ply at 25°C and 100°C, respectively.
- 1 January 2020
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 29 (3) , 285-300
Tensile strength of composite bonded scarf joint in various thermal environmental conditions
This study analyzed variations of tensile strength and the failure mode of composite bonded scarf joint in various thermal environments. A total of 70 scarf bonded joints were manufactured using secondary bonding and co-bonding methods, in which a number of 10 scarf joints were additionally attached to an external ply over the joint area to examine its effect. Six different environmental temperatures ranged from 25°C to 150°C were chosen and tested. A pure laminate having the same stacking sequence as the parent laminate was prepared and tested at the six temperatures for references. Experimental results revealed that tensile strengths of the secondary bonded (SB) and co-bonded (CB) joints at 75°C reduced by 9.3% and 10.5% in comparison with strengths of the corresponding joints at 25°C, respectively. Particularly, at 125°C, which is higher than the resin glass transition temperature, significant reductions of 57.1% and 53.6% in strength were found for SB and CB joints, respectively. In terms of the manufacturing methods, the strengths of the SB joints were higher than those of the CB at 25°C, 50°C, and 75°C by 6.5%, 7.6%, and 8.0%, respectively. However, at high temperatures (100°C, 125°C, and 150°C) these differences were negligible. Strengths of SB joints attached external ply increased by 5.9% and 37.5% compared to those of SB joints without the external ply at 25°C and 100°C, respectively.
- 28 September 2016
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 26 (2) , 115-133
Failure load prediction of laminates repaired with a scarf-bonded patch using the damage zone method
The damage zone method (DZM) is an efficient way to predict the failure of composite structures with a minimum of real testing. Particularly, it is useful when the failure mechanism is too complicated to be accurately analyzed by a merely numerical method. The aim of this study was to use the damage zone model to predict the failure load of repaired laminates, in which scarf-bonded joints were used for repair. The model uses a test-based critical damage zone and stress-based failure criteria. A total of 45 carbon-epoxy composite (USN) laminate scarf-repaired specimens were first tested with two different defect sizes, four scarf angles, and three overlap layer sizes. The Tsai-Wu and Tsai-Hill criteria were used for the laminate, and the maximum shear stress criterion for the adhesive was adopted to predict failure onset. The predicted failure loads were compared to test results and a good agreement was obtained with a 9.2% maximum deviation for almost all parameters with the exception of a case with an unrealistically large scarf angle. To verify the feasibility of the DZM for different material, additional 30 repair specimens using other unidirectional carbon-epoxy laminate were then also tested and the predictions were confirmed by the results of the experiment.
- 28 September 2016
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 26 (2) , 115-133
Failure load prediction of laminates repaired with a scarf-bonded patch using the damage zone method
The damage zone method (DZM) is an efficient way to predict the failure of composite structures with a minimum of real testing. Particularly, it is useful when the failure mechanism is too complicated to be accurately analyzed by a merely numerical method. The aim of this study was to use the damage zone model to predict the failure load of repaired laminates, in which scarf-bonded joints were used for repair. The model uses a test-based critical damage zone and stress-based failure criteria. A total of 45 carbon-epoxy composite (USN) laminate scarf-repaired specimens were first tested with two different defect sizes, four scarf angles, and three overlap layer sizes. The Tsai-Wu and Tsai-Hill criteria were used for the laminate, and the maximum shear stress criterion for the adhesive was adopted to predict failure onset. The predicted failure loads were compared to test results and a good agreement was obtained with a 9.2% maximum deviation for almost all parameters with the exception of a case with an unrealistically large scarf angle. To verify the feasibility of the DZM for different material, additional 30 repair specimens using other unidirectional carbon-epoxy laminate were then also tested and the predictions were confirmed by the results of the experiment.
- 30 June 2016
- Published by The Korean Society for Composite Materials in Composites Research
- Vol. 29 (3) , 117-124
Failure Characteristics of Scarf Patch-repaired Composite Single-lap Joints
- 30 June 2016
- Published by The Korean Society for Composite Materials in Composites Research
- Vol. 29 (3) , 117-124
Failure Characteristics of Scarf Patch-repaired Composite Single-lap Joints
- 31 December 2015
- Published by The Korean Society for Composite Materials in Composites Research
- Vol. 28 (6) , 348-355
Evaluation of Dispersivity and Resistance of the Adhesive Joint According to Dispersion Methods of CNT
- 31 December 2015
- Published by The Korean Society for Composite Materials in Composites Research
- Vol. 28 (6) , 348-355
Evaluation of Dispersivity and Resistance of the Adhesive Joint According to Dispersion Methods of CNT
- 2 October 2015
- Published by Springer Nature in Applied Composite Materials
- Vol. 23 (3) , 397-419
Numerical Modeling of Combined Matrix Cracking and Delamination in Composite Laminates Using Cohesive Elements
- 2 October 2015
- Published by Springer Nature in Applied Composite Materials
- Vol. 23 (3) , 397-419
Numerical Modeling of Combined Matrix Cracking and Delamination in Composite Laminates Using Cohesive Elements
- 31 August 2015
- Published by The Korean Society for Composite Materials in Composites Research
- Vol. 28 (4) , 219-225
Joint Design and Strength Evaluation of Composite Air Spoiler for Ship
- 31 August 2015
- Published by The Korean Society for Composite Materials in Composites Research
- Vol. 28 (4) , 219-225
Joint Design and Strength Evaluation of Composite Air Spoiler for Ship
- 31 August 2014
- Published by The Korean Society for Composite Materials in Composites Research
- Vol. 27 (4) , 158-167
Design and Verification of Shear Buckling Test Fixture for Composite Laminate
- 31 August 2014
- Published by The Korean Society for Composite Materials in Composites Research
- Vol. 27 (4) , 158-167
Design and Verification of Shear Buckling Test Fixture for Composite Laminate