Damian Pysch
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Damian Pysch has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Stefan Glunz
Fraunhofer Institute for Solar Energy Systems ISE Freiburg Germany
3 shared publications Martin Hermle
Fraunhofer Institute for Solar Energy Systems 1 , Heidenhofstr. 2, D-79110 Freiburg, Germany
2 shared publicationsA. Filipovic
Fraunhofer Institute for Solar Energy Systems, Heidenhofstr. 2, D-79110 Freiburg, Germany
1 shared publicationA. Mette
Fraunhofer Institute for Solar Energy Systems, Heidenhofstr. 2, D-79110 Freiburg, Germany
1 shared publicationChristoph Meinhard
Fraunhofer Institute for Solar Energy Systems 1 , Heidenhofstr. 2, D-79110 Freiburg, Germany
1 shared publicationMartin Bivour
Fraunhofer Institute for Solar Energy Systems, Heidenhofstr. 2, D-79110 Freiburg, Germany
1 shared publication
Latest Publications
- 1 November 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 110 (9) , 094516
Analysis and optimization approach for the doped amorphous layers of silicon heterojunction solar cells
Comparison of the open-circuit voltage (external voltage Voc,ext) determined by Suns-Voc measurements with the implied voltage Voc,impl determined by transient photoconductance decay lifetime measurements can yield a quick and easy analysis of silicon heterojunction (SHJ) solar cells, especially in regard to finding the optimum doping concentration of the emitter layer [or back surface field (BSF)]. A sufficiently high doping concentration of the emitter and BSF is mandatory to extract the internal Fermi-level splitting and thus the internal voltage, at the solar cell contacts. However increasing the concentration of doping gases during the deposition of doped amorphous silicon layers results in a reduction of the interface passivation quality and Voc,impl. The best trade off is realized when the ratio of Voc,ext to Voc,impl (external/internal Voc-ratio ζ) reaches a saturation value near 1 upon increasing the doping concentration. AFORS-HET (Automat FOR Simulation of HETerostructures) simulations resulted in the conclusion that the characteristics of the external/internal Voc-ratio are mainly determined by the active doping concentration (doping minus defect concentration).
- 1 November 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 110 (9) , 094516
Analysis and optimization approach for the doped amorphous layers of silicon heterojunction solar cells
Comparison of the open-circuit voltage (external voltage Voc,ext) determined by Suns-Voc measurements with the implied voltage Voc,impl determined by transient photoconductance decay lifetime measurements can yield a quick and easy analysis of silicon heterojunction (SHJ) solar cells, especially in regard to finding the optimum doping concentration of the emitter layer [or back surface field (BSF)]. A sufficiently high doping concentration of the emitter and BSF is mandatory to extract the internal Fermi-level splitting and thus the internal voltage, at the solar cell contacts. However increasing the concentration of doping gases during the deposition of doped amorphous silicon layers results in a reduction of the interface passivation quality and Voc,impl. The best trade off is realized when the ratio of Voc,ext to Voc,impl (external/internal Voc-ratio ζ) reaches a saturation value near 1 upon increasing the doping concentration. AFORS-HET (Automat FOR Simulation of HETerostructures) simulations resulted in the conclusion that the characteristics of the external/internal Voc-ratio are mainly determined by the active doping concentration (doping minus defect concentration).
- 1 February 2011
- Published by Elsevier in Thin Solid Films
- Vol. 519 (8) , 2550-2554
Amorphous silicon carbide heterojunction solar cells on p-type substrates
- 1 February 2011
- Published by Elsevier in Thin Solid Films
- Vol. 519 (8) , 2550-2554
Amorphous silicon carbide heterojunction solar cells on p-type substrates
- 1 October 2008
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 17 (2) , 101-114
Comprehensive analysis of advanced solar cell contacts consisting of printed fine‐line seed layers thickened by silver plating
This work presents a detailed analysis of a new two‐layer process to contact industrial solar cells. However, most of the results seem to be transferable to standard screen print paste contacts. The seed layer was created by a pad or screen printer and thickened by light‐induced plating (LIP) of silver. These contact structures were investigated microscopically to gain a better understanding of the observed electrical parameters. A review of the present microscopic contact formation model for flat surfaces is presented. This model was extended and applied to surfaces textured with random pyramids. This analysis has revealed two new types of silver crystallites which can be described by a crystallographic model. The dependence of the silver crystallite density on the surface doping concentration was investigated. Next, the dependence of the contact resistance on the width of the seed layer was measured showing that the contact resistivity increases with a reduction of the seed layer width. These results have been further approved by an analysis of SEM images of wet‐chemically etched contacts examining the density of crystallites and the fraction of removed SiNx layer. Contact resistance RC measurements before and after LIP of silver showed surprisingly a positive influence of the plating process on RC. A detailed microscopical analysis revealed four new possible current flow paths due to the LIP of a conventional contact or a seed layer. The results led to an extension of the existing model for a screen‐printed contact. Copyright © 2008 John Wiley & Sons, Ltd.
- 1 October 2008
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 17 (2) , 101-114
Comprehensive analysis of advanced solar cell contacts consisting of printed fine‐line seed layers thickened by silver plating
This work presents a detailed analysis of a new two‐layer process to contact industrial solar cells. However, most of the results seem to be transferable to standard screen print paste contacts. The seed layer was created by a pad or screen printer and thickened by light‐induced plating (LIP) of silver. These contact structures were investigated microscopically to gain a better understanding of the observed electrical parameters. A review of the present microscopic contact formation model for flat surfaces is presented. This model was extended and applied to surfaces textured with random pyramids. This analysis has revealed two new types of silver crystallites which can be described by a crystallographic model. The dependence of the silver crystallite density on the surface doping concentration was investigated. Next, the dependence of the contact resistance on the width of the seed layer was measured showing that the contact resistivity increases with a reduction of the seed layer width. These results have been further approved by an analysis of SEM images of wet‐chemically etched contacts examining the density of crystallites and the fraction of removed SiNx layer. Contact resistance RC measurements before and after LIP of silver showed surprisingly a positive influence of the plating process on RC. A detailed microscopical analysis revealed four new possible current flow paths due to the LIP of a conventional contact or a seed layer. The results led to an extension of the existing model for a screen‐printed contact. Copyright © 2008 John Wiley & Sons, Ltd.