Raj Kumar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Raj Kumar has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Nagendra Kushwaha
DIAT (Deemed University)
4 shared publications - Praveen Vummadisetty Naidu
V R Siddhartha Engineering College
4 shared publications Nagendra Kushwaha
Department of Electronics Engineering, DIAT (DU), Pune-411025, India
2 shared publicationsR. V. S. Ram Krishna
DIAT (DU) Research Scholar Girinagar, Pune 411 025 India
2 shared publicationsVivek Kamble
Department of Applied Physics; DIAT(Deemed University); Girinagar Pune 411 025 India
2 shared publicationsI. Srikant
Deemed University
1 shared publication
Latest Publications
- Open Access
- 1 May 2016
- Published by Institution of Engineering and Technology (IET) in IET Microwaves, Antennas & Propagation
- Vol. 10 (7) , 791-796
Microstrip fed square ring slot antenna for ultra‐wideband dual polarisation with good isolation
A square ring shaped planar slot antenna for dual‐polarised applications is presented and experimentally investigated. Each arm of the slot has a stepped rectangular section. Two of the adjacent arms are excited using microstrip feed lines printed on the other side of the substrate. To improve the isolation, a kite shaped slot stub is placed at the centre of the ring and is connected to one of its corners. The antenna has an impedance bandwidth from 3.0 to 12.0 GHz while the isolation is better than 20 dB. The dual polarisation is demonstrated by means of an aperture electric field plot. The antenna has a peak gain varying from 4 to 6 dBi. To check the diversity performance, the envelope correlation coefficient is calculated and found to be within the threshold limit. The antenna will be useful for applications requiring dual polarisation over the ultra‐wide bandwidth with good isolation.
- 1 May 2016
- Published by Institution of Engineering and Technology (IET) in IET Microwaves, Antennas & Propagation
- Vol. 10 (7) , 791-796
Open AccessMicrostrip fed square ring slot antenna for ultra‐wideband dual polarisation with good isolation
A square ring shaped planar slot antenna for dual‐polarised applications is presented and experimentally investigated. Each arm of the slot has a stepped rectangular section. Two of the adjacent arms are excited using microstrip feed lines printed on the other side of the substrate. To improve the isolation, a kite shaped slot stub is placed at the centre of the ring and is connected to one of its corners. The antenna has an impedance bandwidth from 3.0 to 12.0 GHz while the isolation is better than 20 dB. The dual polarisation is demonstrated by means of an aperture electric field plot. The antenna has a peak gain varying from 4 to 6 dBi. To check the diversity performance, the envelope correlation coefficient is calculated and found to be within the threshold limit. The antenna will be useful for applications requiring dual polarisation over the ultra‐wide bandwidth with good isolation.
- 29 April 2016
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 9 (3) , 697-703
Gain enhancement of wideband circularly polarized antenna using FSS
This paper presents a high gain, wideband circularly polarized (CP) antenna. High gain of the antenna is achieved by employing a frequency selective surface (FSS) as a reflector. The antenna is a coplanar waveguide-fed structure with a modified L-shaped radiating patch. The unit element of the FSS is formed by connecting two modified dipoles at an angle of 90°. The antenna with reflector has a measured impedance bandwidth of 74.3% (2.2–4.8 GHz) and a 3-dB axial ratio bandwidth (ARBW) of 62% (2.2–4.18 GHz). The maximum boresight gain of the proposed antenna with reflector is 7.1 dB at 3.4 GHz. The radiation patterns of the antenna with the FSS are also measured and compared with simulated patterns. The various aspects of effect of FSS on CP antenna performance are also discussed.
- 29 April 2016
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 9 (3) , 697-703
Gain enhancement of wideband circularly polarized antenna using FSS
This paper presents a high gain, wideband circularly polarized (CP) antenna. High gain of the antenna is achieved by employing a frequency selective surface (FSS) as a reflector. The antenna is a coplanar waveguide-fed structure with a modified L-shaped radiating patch. The unit element of the FSS is formed by connecting two modified dipoles at an angle of 90°. The antenna with reflector has a measured impedance bandwidth of 74.3% (2.2–4.8 GHz) and a 3-dB axial ratio bandwidth (ARBW) of 62% (2.2–4.18 GHz). The maximum boresight gain of the proposed antenna with reflector is 7.1 dB at 3.4 GHz. The radiation patterns of the antenna with the FSS are also measured and compared with simulated patterns. The various aspects of effect of FSS on CP antenna performance are also discussed.
- 21 March 2016
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 58 (5) , 1181-1187
Design of a compact mimo/diversity antenna for UWB applications with modified TH‐like structure
- 21 March 2016
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 58 (5) , 1181-1187
Design of a compact mimo/diversity antenna for UWB applications with modified TH‐like structure
- 1 January 2016
- Published by The Scientific and Technological Research Council of Turkey (TUBITAK-ULAKBIM) - DIGITAL COMMONS JOURNALS in Turkish Journal of Electrical Engineering and Computer Sciences
- Vol. 24 (4) , 2806-2824
Design of compact octagonal slotted hexagonal and rectangular shaped monopole antennas for dual/UWB applications
- 1 January 2016
- Published by The Scientific and Technological Research Council of Turkey (TUBITAK-ULAKBIM) - DIGITAL COMMONS JOURNALS in Turkish Journal of Electrical Engineering and Computer Sciences
- Vol. 24 (4) , 2806-2824
Design of compact octagonal slotted hexagonal and rectangular shaped monopole antennas for dual/UWB applications
- Open Access
- 1 November 2015
- Published by Institution of Engineering and Technology (IET) in IET Microwaves, Antennas & Propagation
- Vol. 9 (14) , 1595-1604
Compact printed ultra‐wideband diversity monopole antenna with slant inverted tree‐shaped stub
A compact two‐port diversity antenna is proposed and experimentally investigated. One of the ports is connected to a microstrip feed, whereas the other port to a coplanar waveguide feed. The radiating elements are semi‐circular disc‐shaped monopoles rotated around their centres. By shaping the common ground plane, ultra‐wide impedance bandwidth is achieved. The measured bandwidths are 2–12 GHz at port 1 and 2.3–10.2 GHz at port 2. To obtain good isolation between the ports, a slant inverted tree‐shaped structure is attached at the corner of the ground plane. The measured isolation is about 20 dB throughout the band. The antenna has omni‐directional radiation patterns with a moderate peak gain of 2–7 dBi. To evaluate the diversity performance, the envelope correlation coefficient, diversity gain and capacity loss are calculated. A modified design with impedance bandwidth at port 2 extending beyond 11 GHz is also presented. The proposed diversity antenna is an attractive candidate to provide polarisation diversity and enhance channel capacity in a rich scattering environment.
- 1 November 2015
- Published by Institution of Engineering and Technology (IET) in IET Microwaves, Antennas & Propagation
- Vol. 9 (14) , 1595-1604
Open AccessCompact printed ultra‐wideband diversity monopole antenna with slant inverted tree‐shaped stub
A compact two‐port diversity antenna is proposed and experimentally investigated. One of the ports is connected to a microstrip feed, whereas the other port to a coplanar waveguide feed. The radiating elements are semi‐circular disc‐shaped monopoles rotated around their centres. By shaping the common ground plane, ultra‐wide impedance bandwidth is achieved. The measured bandwidths are 2–12 GHz at port 1 and 2.3–10.2 GHz at port 2. To obtain good isolation between the ports, a slant inverted tree‐shaped structure is attached at the corner of the ground plane. The measured isolation is about 20 dB throughout the band. The antenna has omni‐directional radiation patterns with a moderate peak gain of 2–7 dBi. To evaluate the diversity performance, the envelope correlation coefficient, diversity gain and capacity loss are calculated. A modified design with impedance bandwidth at port 2 extending beyond 11 GHz is also presented. The proposed diversity antenna is an attractive candidate to provide polarisation diversity and enhance channel capacity in a rich scattering environment.
- 4 June 2015
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 29 (11) , 1397-1409
Design and analysis of CPW-fed wideband circularly polarized antenna for modern communication systems
A novel design for wideband circularly polarized antenna is presented. The proposed antenna is a coplanar waveguide structure. The slot in the ground plane is rectangular and placed asymmetric. The circular polarization is achieved by using a modified L-shape radiating patch and by adding inverted L-shaped strip at one corner. Axial ratio bandwidth (ARBW) of the antenna is greatly enhanced by connecting one end of the L-shaped patch to the ground via a slit and cutting additional slots in the ground plane. The measured impedance bandwidth and 3 dB ARBW is 3.4 GHz (2.2–5.6 GHz) and 1.97 GHz (2.2–4.17 GHz), respectively, which can cover WLAN (2.4 GHz band), RFID reader (2.45 GHz band), WiMAX (3.2–3.7 GHz band) other wireless communication applications. The average measured boresight gain is 3–4 dBi. The time domain analysis of the antenna is also performed. The measured group delay is nearly constant in the operating band. The system fidelity factor of the antenna is also measured for different azimuth angles.
- 4 June 2015
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 29 (11) , 1397-1409
Design and analysis of CPW-fed wideband circularly polarized antenna for modern communication systems
A novel design for wideband circularly polarized antenna is presented. The proposed antenna is a coplanar waveguide structure. The slot in the ground plane is rectangular and placed asymmetric. The circular polarization is achieved by using a modified L-shape radiating patch and by adding inverted L-shaped strip at one corner. Axial ratio bandwidth (ARBW) of the antenna is greatly enhanced by connecting one end of the L-shaped patch to the ground via a slit and cutting additional slots in the ground plane. The measured impedance bandwidth and 3 dB ARBW is 3.4 GHz (2.2–5.6 GHz) and 1.97 GHz (2.2–4.17 GHz), respectively, which can cover WLAN (2.4 GHz band), RFID reader (2.45 GHz band), WiMAX (3.2–3.7 GHz band) other wireless communication applications. The average measured boresight gain is 3–4 dBi. The time domain analysis of the antenna is also performed. The measured group delay is nearly constant in the operating band. The system fidelity factor of the antenna is also measured for different azimuth angles.
- 25 March 2015
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 57 (5) , 1199-1204
A CPW‐fed wideband circularly polarized slot antenna with FSS for enhanced gain
A CPW fed slot antenna is proposed. The slot is rectangular in shape and is excited by a two step feed terminated on a circular disc which protrudes into the slot center. Perturbations in the form of metallic L‐shape strips are attached at two opposite corners of the slot while the other two slot corners are blended with circular arcs. Further, slant narrow rectangular slits are cut on the circular disc. The frequency selected surface (FSS) designed to improve the gain and the Circular Polarization (CP) of the antenna is an array of rectangular metallic patches printed on one side of a substrate. The antenna—FSS combination achieves an impedance bandwidth of 2.3–12.0 GHz (136%, measured). The 3‐dB axial ratio bandwidth (ARBW) achieved by the combination is from 4.3–6.9 GHz (46.4%, measured). The measured peak gain is 7–8 dBi over much of the band which is an enhancement of about 4 dBi when compared to the antenna without the FSS. The antenna along with the FSS can be useful for CP applications such as in ground penetrating radar and vehicular radar where high gain is additionally required. © 2015 Wiley Periodicals, Inc. Microwave Opt Technol Lett 57:1199–1204, 2015
- 25 March 2015
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 57 (5) , 1199-1204
A CPW‐fed wideband circularly polarized slot antenna with FSS for enhanced gain
A CPW fed slot antenna is proposed. The slot is rectangular in shape and is excited by a two step feed terminated on a circular disc which protrudes into the slot center. Perturbations in the form of metallic L‐shape strips are attached at two opposite corners of the slot while the other two slot corners are blended with circular arcs. Further, slant narrow rectangular slits are cut on the circular disc. The frequency selected surface (FSS) designed to improve the gain and the Circular Polarization (CP) of the antenna is an array of rectangular metallic patches printed on one side of a substrate. The antenna—FSS combination achieves an impedance bandwidth of 2.3–12.0 GHz (136%, measured). The 3‐dB axial ratio bandwidth (ARBW) achieved by the combination is from 4.3–6.9 GHz (46.4%, measured). The measured peak gain is 7–8 dBi over much of the band which is an enhancement of about 4 dBi when compared to the antenna without the FSS. The antenna along with the FSS can be useful for CP applications such as in ground penetrating radar and vehicular radar where high gain is additionally required. © 2015 Wiley Periodicals, Inc. Microwave Opt Technol Lett 57:1199–1204, 2015
- 10 February 2015
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 8 (2) , 363-368
An UWB dual polarized microstrip fed L-shape slot antenna
In this paper, a microstrip fed, L-shape slot antenna for dual polarization is proposed. The two arms of the slot generate electric fields of orthogonal polarizations. By properly sectioning the slot and the feed line, ultra wideband (UWB) behavior is obtained. The measured impedance bandwidth (S11< −10 dB) is more than 8.6 GHz (112%) and 8.2 GHz (104%) for Port 1 and Port 2, respectively. The measured isolation is better than 25 dB over most of the band. The aperture field distribution justifies the dual polarized nature. A modified version which implements a band-notch over 5.1–5.85 GHz wireless local area network (WLAN) band is also presented. With a compact, single substrate design, the antenna can be useful in MIMO transmission systems, polarimetric UWB radar, high performance microwave imaging, and other future wireless communications devices.
- 10 February 2015
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 8 (2) , 363-368
An UWB dual polarized microstrip fed L-shape slot antenna
In this paper, a microstrip fed, L-shape slot antenna for dual polarization is proposed. The two arms of the slot generate electric fields of orthogonal polarizations. By properly sectioning the slot and the feed line, ultra wideband (UWB) behavior is obtained. The measured impedance bandwidth (S11< −10 dB) is more than 8.6 GHz (112%) and 8.2 GHz (104%) for Port 1 and Port 2, respectively. The measured isolation is better than 25 dB over most of the band. The aperture field distribution justifies the dual polarized nature. A modified version which implements a band-notch over 5.1–5.85 GHz wireless local area network (WLAN) band is also presented. With a compact, single substrate design, the antenna can be useful in MIMO transmission systems, polarimetric UWB radar, high performance microwave imaging, and other future wireless communications devices.
- 18 December 2014
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 57 (2) , 314-319
Design of a compact CPW-feed asymmetric elliptical slot ultrawideband antenna for high gain
- 18 December 2014
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 57 (2) , 314-319
Design of a compact CPW-feed asymmetric elliptical slot ultrawideband antenna for high gain
- 17 October 2014
- Published by Springer Nature in Wireless Personal Communications
- Vol. 80 (3) , 1175-1192
Simulation, Design of Compact Multi-band Microstrip Slot Antennas for WiMAX/WLAN and UWB Applications
- 17 October 2014
- Published by Springer Nature in Wireless Personal Communications
- Vol. 80 (3) , 1175-1192
Simulation, Design of Compact Multi-band Microstrip Slot Antennas for WiMAX/WLAN and UWB Applications