Vladimir Popovic
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vladimir Popovic has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Dragan Stamenković
University of Belgrade, Faculty of Mechanical Engineering, Kraljice Marije 16, 11120 Belgrade, Serbia
3 shared publications - Ivan Blagojević
Faculty of Mechanical Engineering, University of Belgrade, Belgrade, Serbia
3 shared publications - Aleksandar Grbović
University of Belgrade
1 shared publication - Aleksandar Micovic
Faculty of Technical Sciences, University of Priština, Kosovska Mitrovica
1 shared publication - Aleksandar Mićović
Technical Test Centre, Vojvode Stepe 445, 11000 Belgrade, Serbia
1 shared publication - Aleksandar Vencl
University of Belgrade, Faculty of Mechanical Engineering, Kraljice Marije 16, 11120 Belgrade, Serbia
1 shared publication
Latest Publications
- Open Access
- 15 December 2024
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 31 (6) , 2064-2071
Market Performance and Customer Satisfaction Relation in Automotive Sales, Maintenance, and other Services
The distribution networks of car dealers are in transformation with challenge to evolute and increase portfolio of services and secure sustainability or languish. This paper presents the performance of four automotive dealers regarding their business...
- 15 December 2024
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 31 (6) , 2064-2071
Open AccessMarket Performance and Customer Satisfaction Relation in Automotive Sales, Maintenance, and other Services
The distribution networks of car dealers are in transformation with challenge to evolute and increase portfolio of services and secure sustainability or languish. This paper presents the performance of four automotive dealers regarding their business...
- Open Access
- 15 February 2023
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 30 (1) , 122-130
Solving the Problem of Friction and Wear in Auxiliary Devices of Internal Combustion Engines on the Example of Reciprocating Air Compressor for Vehicles
Using vehicles and other mobile systems to transport passengers and goods, approximately 25% of Europe's greenhouse gases are generated. At the same time, many research papers, published by researchers and students, promote the use of electric vehicl...
- 15 February 2023
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 30 (1) , 122-130
Open AccessSolving the Problem of Friction and Wear in Auxiliary Devices of Internal Combustion Engines on the Example of Reciprocating Air Compressor for Vehicles
Using vehicles and other mobile systems to transport passengers and goods, approximately 25% of Europe's greenhouse gases are generated. At the same time, many research papers, published by researchers and students, promote the use of electric vehicl...
- Open Access
- 1 February 2023
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 30 (1) , 87-92
Verification of the Numerical Model of Optimized Bus Body Structure According to UN Regulation No. 66
Bus rollover is one of the most analyzed cases of accidents, having in mind the number of potential large number of injuries and fatalities. Therefore, this type of traffic accident became the object of numerous national and international standards and regulations. The aim of this paper is to investigate the possibilities of experimental verification of presented simplified model of the bus body section. For that purpose, completely new multifunctional test bench was presented. The methodology applied for the experimental part was explained. The results provided by the numerical simulation and by the experiment were presented, and appropriate analyses were performed. The key parameters needed for the experimental verification were specified. According to the result analysis, a comparative results review was presented, confirming that the experimental verification of the numerical model was fully acceptable. Also, all of the requirements prescribed by the applied methodology for the achieved results acceptance were fulfilled, providing that numerical simulation, with constant improvements, could be a powerful tool for quick and reliable bus structure analysis in design process.
- 1 February 2023
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 30 (1) , 87-92
Open AccessVerification of the Numerical Model of Optimized Bus Body Structure According to UN Regulation No. 66
Bus rollover is one of the most analyzed cases of accidents, having in mind the number of potential large number of injuries and fatalities. Therefore, this type of traffic accident became the object of numerous national and international standards and regulations. The aim of this paper is to investigate the possibilities of experimental verification of presented simplified model of the bus body section. For that purpose, completely new multifunctional test bench was presented. The methodology applied for the experimental part was explained. The results provided by the numerical simulation and by the experiment were presented, and appropriate analyses were performed. The key parameters needed for the experimental verification were specified. According to the result analysis, a comparative results review was presented, confirming that the experimental verification of the numerical model was fully acceptable. Also, all of the requirements prescribed by the applied methodology for the achieved results acceptance were fulfilled, providing that numerical simulation, with constant improvements, could be a powerful tool for quick and reliable bus structure analysis in design process.
- Open Access
- 1 November 2019
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 26 (6) , 1614-1619
Development of Pedestrian Alert System for Use in Electric Vehicles
Modern technology has made electric vehicles more accessible, which is important for the preservation of the environment. Although eco-friendly, from the standpoint of pedestrian safety, they may be baleful. The low levels of noise...
- 1 November 2019
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 26 (6) , 1614-1619
Open AccessDevelopment of Pedestrian Alert System for Use in Electric Vehicles
Modern technology has made electric vehicles more accessible, which is important for the preservation of the environment. Although eco-friendly, from the standpoint of pedestrian safety, they may be baleful. The low levels of noise...
- Open Access
- 1 August 2017
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 24 (4) , 1213-1219
Electric vehicle conversion: optimisation of parameters in the design process
Jedan od pravaca ka stvaranju čistijih i ekonomičnijih vozila jeste prihvatanje koncepta električnog vozila. Rad predstavlja suvremene koncepte konstrukcije električnih vozila širom svijeta, kao i načine snabdjevanja vozila...
- 1 August 2017
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 24 (4) , 1213-1219
Open AccessElectric vehicle conversion: optimisation of parameters in the design process
Jedan od pravaca ka stvaranju čistijih i ekonomičnijih vozila jeste prihvatanje koncepta električnog vozila. Rad predstavlja suvremene koncepte konstrukcije električnih vozila širom svijeta, kao i načine snabdjevanja vozila...
- 1 January 2013
- Published by National Library of Serbia in Thermal Science
- Vol. 17 (1) , 91-105
Energy efficiency improvement by gear shifting optimization
Many studies have proved that elements of driver’s behavior related to gear selection have considerable influence on the fuel consumption. Optimal gear shifting is a complex task, especially for inexperienced drivers. This paper presents an implemented idea for gear shifting optimization with the aim of fuel consumption minimization with more efficient engine working regimes. Optimized gear shifting enables the best possible relation between vehicle motion regimes and engine working regimes. New theoretical-experimental approach has been developed using On-Board Diagnostic technology which so far has not been used for this purpose. The matrix of driving modes according to which tests were performed is obtained and special data acquisition system and analysis process have been developed. Functional relations between experimental test modes and adequate engine working parameters have been obtained and all necessary operations have been conducted to enable their use as inputs for the designed algorithm. The created Model has been tested in real exploitation conditions on passenger car with Otto fuel injection engine and On-Board Diagnostic connection without any changes on it. The conducted tests have shown that the presented Model has significantly positive effects on fuel consumption which is an important ecological aspect. Further development and testing of the Model allows implementation in wide range of motor vehicles with various types of internal combustion engines
- 1 January 2013
- Published by National Library of Serbia in Thermal Science
- Vol. 17 (1) , 91-105
Energy efficiency improvement by gear shifting optimization
Many studies have proved that elements of driver’s behavior related to gear selection have considerable influence on the fuel consumption. Optimal gear shifting is a complex task, especially for inexperienced drivers. This paper presents an implemented idea for gear shifting optimization with the aim of fuel consumption minimization with more efficient engine working regimes. Optimized gear shifting enables the best possible relation between vehicle motion regimes and engine working regimes. New theoretical-experimental approach has been developed using On-Board Diagnostic technology which so far has not been used for this purpose. The matrix of driving modes according to which tests were performed is obtained and special data acquisition system and analysis process have been developed. Functional relations between experimental test modes and adequate engine working parameters have been obtained and all necessary operations have been conducted to enable their use as inputs for the designed algorithm. The created Model has been tested in real exploitation conditions on passenger car with Otto fuel injection engine and On-Board Diagnostic connection without any changes on it. The conducted tests have shown that the presented Model has significantly positive effects on fuel consumption which is an important ecological aspect. Further development and testing of the Model allows implementation in wide range of motor vehicles with various types of internal combustion engines
- 1 October 2012
- Published by Taylor & Francis in International Journal of Systems Science
- Vol. 43 (10) , 1913-1926
Optimisation of maintenance concept choice using risk-decision factor – a case study
The design of maintenance system and the corresponding logistic support is a very complex process, during which the aim is to find the compromise solutions regarding the relations among different maintenance procedures and the ways of their implementation. As a result of this, various solutions can be adopted, since this is conditioned by a series of important factors and criteria, which can be contradictory sometimes. There are different perspectives on ways of solving practical maintenance problems, that is dilemmas when it comes to the choice of maintenance concept. The principal dilemma is how and when to decide on carrying out maintenance procedures. Should the decision be based on theoretical grounds or experience, how does one reconcile those two extremes, who is to decide upon this? In this article we have offered one, basically new solution as a possibility for maintenance concept choice, based on a significant modification of the widely used failure modes and effects analysis (FMEA) method. This solution is risk-decision factor (RDF). This is a result of seven parameters (of different importance and weight) that have the key impact on the process of production and logistic support. The application of this factor is illustrated by the example of planning, organisation and functioning of the maintenance system applied in The Institute for Manufacturing Banknotes and Coins (ZIN) in Belgrade.
- 1 October 2012
- Published by Taylor & Francis in International Journal of Systems Science
- Vol. 43 (10) , 1913-1926
Optimisation of maintenance concept choice using risk-decision factor – a case study
The design of maintenance system and the corresponding logistic support is a very complex process, during which the aim is to find the compromise solutions regarding the relations among different maintenance procedures and the ways of their implementation. As a result of this, various solutions can be adopted, since this is conditioned by a series of important factors and criteria, which can be contradictory sometimes. There are different perspectives on ways of solving practical maintenance problems, that is dilemmas when it comes to the choice of maintenance concept. The principal dilemma is how and when to decide on carrying out maintenance procedures. Should the decision be based on theoretical grounds or experience, how does one reconcile those two extremes, who is to decide upon this? In this article we have offered one, basically new solution as a possibility for maintenance concept choice, based on a significant modification of the widely used failure modes and effects analysis (FMEA) method. This solution is risk-decision factor (RDF). This is a result of seven parameters (of different importance and weight) that have the key impact on the process of production and logistic support. The application of this factor is illustrated by the example of planning, organisation and functioning of the maintenance system applied in The Institute for Manufacturing Banknotes and Coins (ZIN) in Belgrade.
- 13 April 2012
- Published by Taylor & Francis in Transportation Planning and Technology
- Vol. 35 (3) , 241-261
Defining the functional and physical compatibility of a modernized tramway rolling stock with a newly planned LRT system: a case study of Belgrade
According to the Belgrade Master Plan for 2021, the public transportation system for the city and its region will include three rail modes: a modernized existing tramway, regional rail, and a new light rail transit (LRT) mode. In the coming years all three rail modes should be developed simultaneously and in a coordinated manner. The introduction of LRT is to be realized in several phases, and its first line will partially follow the alignment of an existing tramway line. As the present tramway vehicles are obsolete, new rolling stock must be designed and purchased to be compatible with many of the elements of the LRT. Ways to adjust the new tramways to the LRT rolling stock represent the central topic of this paper. The basic technical and operating characteristics of the new tramway are defined with respect to their required compatibility with the LRT stock and infrastructure.
- 13 April 2012
- Published by Taylor & Francis in Transportation Planning and Technology
- Vol. 35 (3) , 241-261
Defining the functional and physical compatibility of a modernized tramway rolling stock with a newly planned LRT system: a case study of Belgrade
According to the Belgrade Master Plan for 2021, the public transportation system for the city and its region will include three rail modes: a modernized existing tramway, regional rail, and a new light rail transit (LRT) mode. In the coming years all three rail modes should be developed simultaneously and in a coordinated manner. The introduction of LRT is to be realized in several phases, and its first line will partially follow the alignment of an existing tramway line. As the present tramway vehicles are obsolete, new rolling stock must be designed and purchased to be compatible with many of the elements of the LRT. Ways to adjust the new tramways to the LRT rolling stock represent the central topic of this paper. The basic technical and operating characteristics of the new tramway are defined with respect to their required compatibility with the LRT stock and infrastructure.
- 1 January 2012
- Published by IACSIT Press in International Journal of Applied Physics and Mathematics
- p. 333-335
Choosing the Right Warranty Policy – from the Customer’sto the Manufacturer’s Point of View
- 1 January 2012
- Published by IACSIT Press in International Journal of Applied Physics and Mathematics
- p. 333-335
Choosing the Right Warranty Policy – from the Customer’sto the Manufacturer’s Point of View