Jens Schumacher
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jens Schumacher has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Brigitte Clausen
Foundation Institute of Materials Science (IWT), Badgasteinerstr. 3, 28359 Bremen, Germany
3 shared publications - Hans-Werner Zoch
University of Bremen
2 shared publications Brigitte Clausen
1 shared publicationFrank Jablonski
1 shared publicationFrank Vollertsen
1 shared publication- Jun Zhang
IWT - Leibniz-Institut für Werkstofforientierte Technologien, Bremen, Germany
1 shared publication
Latest Publications
- Open Access
- 10 August 2021
- Published by Wiley in Steel Research International
- Vol. 92 (12)
Calculation of the Fatigue Limit of High‐Strength Steel Specimens at Different Loading Conditions Based on Inclusion Sizes
A calculation method for the fatigue limit of components made of high‐strength steels that fail at inclusions is described. The method consists of two parts: first, the size of failure‐critical inclusions is determined based on metallographic investigations. Then, the fatigue limit is determined based on the expected inclusion sizes using a fracture mechanics model. Influencing factors such as sample size, heat‐treatment conditions, and mean stresses are considered. The model parameters are derived from fatigue test data collected over decades within the framework of several research projects. The dominant influencing factors are the inclusion size and the hardness of the steel matrix. Finally, the model is used to predict the fatigue limit of different specimens made of a bearing steel SAE 52 100. The sizes of failure‐critical inclusions and fatigue limits calculated with the model are compared and evaluated on the basis of the inclusion sizes found in the samples’ fracture surface and the experimentally determined fatigue limits.
- 10 August 2021
- Published by Wiley in Steel Research International
- Vol. 92 (12)
Open AccessCalculation of the Fatigue Limit of High‐Strength Steel Specimens at Different Loading Conditions Based on Inclusion Sizes
A calculation method for the fatigue limit of components made of high‐strength steels that fail at inclusions is described. The method consists of two parts: first, the size of failure‐critical inclusions is determined based on metallographic investigations. Then, the fatigue limit is determined based on the expected inclusion sizes using a fracture mechanics model. Influencing factors such as sample size, heat‐treatment conditions, and mean stresses are considered. The model parameters are derived from fatigue test data collected over decades within the framework of several research projects. The dominant influencing factors are the inclusion size and the hardness of the steel matrix. Finally, the model is used to predict the fatigue limit of different specimens made of a bearing steel SAE 52 100. The sizes of failure‐critical inclusions and fatigue limits calculated with the model are compared and evaluated on the basis of the inclusion sizes found in the samples’ fracture surface and the experimentally determined fatigue limits.
- Open Access
- 25 May 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 165, 14003
Influence of inclusion type and size on the fatigue strength of high strength steels
In this investigation the influence of the inclusion type and size on the fatigue strength of different steels is analysed. As database case hardened, quenched and tempered as well as bearing steels in different heat treatment conditions, which have been investigated in several research projects over the last two decades, are used. Based on the approach of Murakami the local stress intensity at inclusions was determined to evaluate the influence of fracture causing inclusions on the fatigue strength. Different fatigue criteria have been used to calculate the local equivalent stress amplitudes considering residual stresses in the specimens, mean stresses during loading and multiaxial stresses in notched specimens. Since many run out specimens were subsequently fatigued at a higher stress amplitude, the critical inclusion type and size which have survived the initial stress amplitude could be determined. As a result the local stress intensity at inclusions which leads to no fatigue failure could be calculated as well. With the knowledge of the stress intensity factor range of the fractured and run out specimens a threshold stress intensity factor range could be derived for the different steels and inclusion sizes.
- 25 May 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 165, 14003
Open AccessInfluence of inclusion type and size on the fatigue strength of high strength steels
In this investigation the influence of the inclusion type and size on the fatigue strength of different steels is analysed. As database case hardened, quenched and tempered as well as bearing steels in different heat treatment conditions, which have been investigated in several research projects over the last two decades, are used. Based on the approach of Murakami the local stress intensity at inclusions was determined to evaluate the influence of fracture causing inclusions on the fatigue strength. Different fatigue criteria have been used to calculate the local equivalent stress amplitudes considering residual stresses in the specimens, mean stresses during loading and multiaxial stresses in notched specimens. Since many run out specimens were subsequently fatigued at a higher stress amplitude, the critical inclusion type and size which have survived the initial stress amplitude could be determined. As a result the local stress intensity at inclusions which leads to no fatigue failure could be calculated as well. With the knowledge of the stress intensity factor range of the fractured and run out specimens a threshold stress intensity factor range could be derived for the different steels and inclusion sizes.
- 4 December 2014
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 45 (12) , 1108-1115
Strength and failure behaviour of carbon fibre reinforced plastics (CFRP)-aluminium seam structures
- 4 December 2014
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 45 (12) , 1108-1115
Strength and failure behaviour of carbon fibre reinforced plastics (CFRP)-aluminium seam structures