Jacob H. Leach
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jacob H. Leach has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
M. Wu
Virginia Commonwealth Univ. (United States)
8 shared publicationsX. Li
Department of Electrical and Computer Engineering, Virginia Commonwealth University, Richmond, VA, 23284, USA
7 shared publicationsÜ. Özgür
Virginia Commonwealth University 1 Department of Electrical and Computer Engineering Richmond, Virginia 23284, USA
7 shared publicationsH. Morkoç
Virginia Commonwealth Univ. (United States)
6 shared publicationsX. Ni
Virginia Commonwealth University 1 Department of Electrical and Computer Engineering Richmond, Virginia 23284, USA
5 shared publications- Hadis Morkoc
Department of Electrical and Computer Engineering, Virginia Commonwealth University, Richmond, VA 23284, USA
4 shared publications
Latest Publications
- 14 March 2011
- Published by Wiley in physica status solidi (c)
- Vol. 8 (5) , 1539-1543
Measurements of generation‐recombination effect by low‐frequency phase‐noise technique in AlGaN/GaN MOSHFETs
- 14 March 2011
- Published by Wiley in physica status solidi (c)
- Vol. 8 (5) , 1539-1543
Measurements of generation‐recombination effect by low‐frequency phase‐noise technique in AlGaN/GaN MOSHFETs
- 10 February 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7939, 79391P
Heterostructure designs for enhanced performance and reliability in GaN HFETs: camelback channels
The electric fields present in a heterostructure field effect transistor (HFET) give rise to large densities of hot electrons and hot phonons not in equilibrium with the lattice (thus the term "hot"). Hot electrons give rise to an accumulation of hot phonons, which play a deleterious role in device performance and reliability, particularly as 2DEG densities increase. Thus, it is important that hot phonon effects be mitigated. The hot phonon effect arises due to the fact that LO phonon (longitudinal optical phonon) scattering is the primary scattering mechanism at high fields in GaN, and that LO phonons tend to accumulate in the channel due to long lifetimes and low group velocity; minimizing the existence in time of hot phonons in the channel is the overall goal. That said, the lifetime of the LO phonons decaying into propagating LA modes is not constant, and it is through the exploitation of this fact that one gains the ability to enhance the performance and reliability of HFETs. This has been evidenced by operating HFETs at particular bias conditions which tend to lend themselves to relatively short LO phonon lifetimes. Alternatively, minimization of hot phonon lifetimes may be achieved through novel device designs. In this work, we outline designs for minimizing hot phonon effects in HFET devices with sheet densities >2 x 1013 cm-2. We propose "camel-back" structures with wavefunction "spreading layers" to maximize 2DEG charge while mitigating hot phonon effects arising from high density 2DEGs.
- 10 February 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7939, 79391P
Heterostructure designs for enhanced performance and reliability in GaN HFETs: camelback channels
The electric fields present in a heterostructure field effect transistor (HFET) give rise to large densities of hot electrons and hot phonons not in equilibrium with the lattice (thus the term "hot"). Hot electrons give rise to an accumulation of hot phonons, which play a deleterious role in device performance and reliability, particularly as 2DEG densities increase. Thus, it is important that hot phonon effects be mitigated. The hot phonon effect arises due to the fact that LO phonon (longitudinal optical phonon) scattering is the primary scattering mechanism at high fields in GaN, and that LO phonons tend to accumulate in the channel due to long lifetimes and low group velocity; minimizing the existence in time of hot phonons in the channel is the overall goal. That said, the lifetime of the LO phonons decaying into propagating LA modes is not constant, and it is through the exploitation of this fact that one gains the ability to enhance the performance and reliability of HFETs. This has been evidenced by operating HFETs at particular bias conditions which tend to lend themselves to relatively short LO phonon lifetimes. Alternatively, minimization of hot phonon lifetimes may be achieved through novel device designs. In this work, we outline designs for minimizing hot phonon effects in HFET devices with sheet densities >2 x 1013 cm-2. We propose "camel-back" structures with wavefunction "spreading layers" to maximize 2DEG charge while mitigating hot phonon effects arising from high density 2DEGs.
- 14 June 2010
- Published by Wiley in Physica Status Solidi (a)
- Vol. 207 (6) , 1345-1347
Stress test measurements of lattice‐matched InAlN/AlN/GaN HFET structures
InAlN/GaN heterostructures offer some benefits over existing AlGaN/GaN heterostructures for HFET device applications. In addition to having a larger bandgap than typical AlGaN compounds used in HFET devices (with Al < 30%), which leads to better confinement and subsequent larger power carrying capacity, InAlN can be grown lattice‐matched to GaN, resulting in strain‐free heterostructures. As such, lattice‐matched InAlN provides a unique system wherein the reliability of the devices may exceed that of the strained AlGaN/GaN devices as a result of being able to decouple the hot electron/hot phonon effects on the reliability from the strain related issues. In this work, we subjected lattice‐matched InAlN‐based HFETs to electrical stress and observed the corresponding degradation in maximum drain current. We found that the degradation rates are lower only for a narrow range of moderate gate biases, corresponding to low field average 2‐dimensional electron gas (2DEG) densities of 9–10 × 1012 cm−2. We propose that the degradation is attributable to the buildup of hot phonons since the degradation rates as a function of electron density generally follow the hot phonon lifetime versus electron density. This provides evidence that hot phonons have a significant role in device degradation and there exists an optimal 2DEG density to minimize hot phonon related degradation. We did not observe any correlation between the degradation rate and the gate leakage.
- 14 June 2010
- Published by Wiley in Physica Status Solidi (a)
- Vol. 207 (6) , 1345-1347
Stress test measurements of lattice‐matched InAlN/AlN/GaN HFET structures
InAlN/GaN heterostructures offer some benefits over existing AlGaN/GaN heterostructures for HFET device applications. In addition to having a larger bandgap than typical AlGaN compounds used in HFET devices (with Al < 30%), which leads to better confinement and subsequent larger power carrying capacity, InAlN can be grown lattice‐matched to GaN, resulting in strain‐free heterostructures. As such, lattice‐matched InAlN provides a unique system wherein the reliability of the devices may exceed that of the strained AlGaN/GaN devices as a result of being able to decouple the hot electron/hot phonon effects on the reliability from the strain related issues. In this work, we subjected lattice‐matched InAlN‐based HFETs to electrical stress and observed the corresponding degradation in maximum drain current. We found that the degradation rates are lower only for a narrow range of moderate gate biases, corresponding to low field average 2‐dimensional electron gas (2DEG) densities of 9–10 × 1012 cm−2. We propose that the degradation is attributable to the buildup of hot phonons since the degradation rates as a function of electron density generally follow the hot phonon lifetime versus electron density. This provides evidence that hot phonons have a significant role in device degradation and there exists an optimal 2DEG density to minimize hot phonon related degradation. We did not observe any correlation between the degradation rate and the gate leakage.
- 15 April 2010
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 107 (8) , 084511
Large dielectric tuning and microwave phase shift at low electric field in epitaxial Ba0.5Sr0.5TiO3 on SrTiO3
Dielectric properties of annealed and as-grown ferroelectric (BST) grown by pulsed laser deposition on sputtered BST seed layers on strontium titanate (STO) substrates were investigated at microwave frequencies in the realm of tunability of its dielectric constant as well as phase shifters based on this material. The as-grown layers were nearly fully relaxed with measured lattice parameters nearly identical to those of bulk BST. The tuning of the relative dielectric constant ( at zero bias at 10 GHz) of the annealed BST was found to be as high as 59% and 56% at 10 and 19 GHz, respectively. The analysis of the loss in the BST results in a measured of 0.02 for the annealed as well as the unannealed films at a frequency of 18 GHz. Phase shifters also exhibited high tuning with differential phase shift figures of merit of 35 and 55°/dB at a field of 60 kV/cm at 10 and 19 GHz, respectively. Serendipitously, most of the tuning occurs at low fields, and thus we propose a new figure of merit, taking into account the amplitude of applied electric field in order to achieve the phase shift. In this new realm we achieved the values of this overall figure of merit of 1.2 and at 10 and 19 GHz, respectively, using an applied electric field of only 10 kV/cm.- 15 April 2010
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 107 (8) , 084511
Large dielectric tuning and microwave phase shift at low electric field in epitaxial Ba0.5Sr0.5TiO3 on SrTiO3
Dielectric properties of annealed and as-grown ferroelectric (BST) grown by pulsed laser deposition on sputtered BST seed layers on strontium titanate (STO) substrates were investigated at microwave frequencies in the realm of tunability of its dielectric constant as well as phase shifters based on this material. The as-grown layers were nearly fully relaxed with measured lattice parameters nearly identical to those of bulk BST. The tuning of the relative dielectric constant ( at zero bias at 10 GHz) of the annealed BST was found to be as high as 59% and 56% at 10 and 19 GHz, respectively. The analysis of the loss in the BST results in a measured of 0.02 for the annealed as well as the unannealed films at a frequency of 18 GHz. Phase shifters also exhibited high tuning with differential phase shift figures of merit of 35 and 55°/dB at a field of 60 kV/cm at 10 and 19 GHz, respectively. Serendipitously, most of the tuning occurs at low fields, and thus we propose a new figure of merit, taking into account the amplitude of applied electric field in order to achieve the phase shift. In this new realm we achieved the values of this overall figure of merit of 1.2 and at 10 and 19 GHz, respectively, using an applied electric field of only 10 kV/cm.- 15 April 2010
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 107 (8) , 083706
Bias dependent two-channel conduction in InAlN/AlN/GaN structures
Due to growth temperature differences during deposition of GaN heterostructures utilizing InAlN barriers, an inadvertent parasitic GaN layer can form in the InAlN barrier layer. In structures utilizing AlN spacer layers, this parasitic layer acts as a second conduction channel with a carrier density dependent upon polarization charges and lattice strain as well as the surface potential. The effect of an additional GaN spacer layer in InAlN/AlN/GaN structures is assessed using simulations, electron-microscopy observations, magnetoconductivity measurements with gated Hall bar samples, and with quantitative mobility spectrum analysis. We propose a possible formation mechanism for the parasitic layer, and note that although the additional unintended layer may have beneficial aspects, we discuss a strategy to prevent its occurrence.
- 15 April 2010
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 107 (8) , 083706
Bias dependent two-channel conduction in InAlN/AlN/GaN structures
Due to growth temperature differences during deposition of GaN heterostructures utilizing InAlN barriers, an inadvertent parasitic GaN layer can form in the InAlN barrier layer. In structures utilizing AlN spacer layers, this parasitic layer acts as a second conduction channel with a carrier density dependent upon polarization charges and lattice strain as well as the surface potential. The effect of an additional GaN spacer layer in InAlN/AlN/GaN structures is assessed using simulations, electron-microscopy observations, magnetoconductivity measurements with gated Hall bar samples, and with quantitative mobility spectrum analysis. We propose a possible formation mechanism for the parasitic layer, and note that although the additional unintended layer may have beneficial aspects, we discuss a strategy to prevent its occurrence.
- 29 March 2010
- Published by AIP Publishing in Applied Physics Letters
- Vol. 96 (13) , 133505
Effect of hot phonon lifetime on electron velocity in InAlN/AlN/GaN heterostructure field effect transistors on bulk GaN substrates
We report on electron velocities deduced from current gain cutoff frequency measurements on GaN heterostructure field effect transistors (HFETs) with InAlN barriers on Fe-doped semi-insulating bulk GaN substrates. The intrinsic transit time is a strong function of the applied gate bias, and a minimum intrinsic transit time occurs for gate biases corresponding to two-dimensional electron gas densities near . This value correlates with the independently observed density giving the minimum longitudinal optical phonon lifetime. We expect the velocity, which is inversely proportional to the intrinsic transit time, to be limited by scattering with non equilibrium (hot) phonons at the high fields present in the HFET channel, and thus, we interpret the minimum intrinsic transit time in terms of the hot phonon decay. At the gate bias associated with the minimum transit time, we determined the average electron velocity for a gate length device to be .- 29 March 2010
- Published by AIP Publishing in Applied Physics Letters
- Vol. 96 (13) , 133505
Effect of hot phonon lifetime on electron velocity in InAlN/AlN/GaN heterostructure field effect transistors on bulk GaN substrates
We report on electron velocities deduced from current gain cutoff frequency measurements on GaN heterostructure field effect transistors (HFETs) with InAlN barriers on Fe-doped semi-insulating bulk GaN substrates. The intrinsic transit time is a strong function of the applied gate bias, and a minimum intrinsic transit time occurs for gate biases corresponding to two-dimensional electron gas densities near . This value correlates with the independently observed density giving the minimum longitudinal optical phonon lifetime. We expect the velocity, which is inversely proportional to the intrinsic transit time, to be limited by scattering with non equilibrium (hot) phonons at the high fields present in the HFET channel, and thus, we interpret the minimum intrinsic transit time in terms of the hot phonon decay. At the gate bias associated with the minimum transit time, we determined the average electron velocity for a gate length device to be .- 8 March 2010
- Published by AIP Publishing in Applied Physics Letters
- Vol. 96 (10) , 102109
Carrier velocity in InAlN/AlN/GaN heterostructure field effect transistors on Fe-doped bulk GaN substrates
We report microwave characteristics of field effect transistors employing InAlN/AlN/GaN heterostructures grown on low-defect-density bulk Fe-doped GaN substrates. We achieved unity current gain cutoff frequencies of 14.3 and 23.7 GHz for devices with gate lengths of 1 and , respectively. Measurements as a function of applied bias allow us to estimate the average carrier velocity in the channel to be for a device. Additionally, we found nearly no gate lag in the devices, which is considered a precondition for good performance under large signal operation.- 8 March 2010
- Published by AIP Publishing in Applied Physics Letters
- Vol. 96 (10) , 102109
Carrier velocity in InAlN/AlN/GaN heterostructure field effect transistors on Fe-doped bulk GaN substrates
We report microwave characteristics of field effect transistors employing InAlN/AlN/GaN heterostructures grown on low-defect-density bulk Fe-doped GaN substrates. We achieved unity current gain cutoff frequencies of 14.3 and 23.7 GHz for devices with gate lengths of 1 and , respectively. Measurements as a function of applied bias allow us to estimate the average carrier velocity in the channel to be for a device. Additionally, we found nearly no gate lag in the devices, which is considered a precondition for good performance under large signal operation.- 11 February 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7602, 76020O-76020
Measurements of gate lag in high-quality nearly lattice matched InAlN/AlN/GaN HFET structures
The promise of InAlN-based HFET devices stems from the relatively large band and spontaneous polarization discontinuities and at the interface and the lack of misfit strain when grown lattice matched to GaN. However, there still exists some question as to what the true lattice matching condition of InAlN to GaN is due to discrepancies in the literature values of lattice parameters of the InN binary, and of the InAlN bowing parameters. We used the gate lag measurement as a supplementary technique to verify lattice matching to the underlying GaN, as we expect the strain in layers one source of lag, associated with piezoelectric charge at the surface. We observe very low lag for nearly lattice matched barrier and barriers under tensile strain, and a marked increase as the composition deviates from the lattice matched condition toward compressively strained layers. Additionally, FETs fabricated on a nearly lattice matched InAlN layer boasted a maximum drain current of over 1.5A/mm and ~2.0A/mm and transconductances of ~275mS/mm and ~300mS/mm at DC and in pulsed modes, respectively, and a cutoff frequency of 15.9GHz (an fT*LG product of 10.3) for a gate length of 0.65μm.
- 11 February 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7602, 76020O-76020
Measurements of gate lag in high-quality nearly lattice matched InAlN/AlN/GaN HFET structures
The promise of InAlN-based HFET devices stems from the relatively large band and spontaneous polarization discontinuities and at the interface and the lack of misfit strain when grown lattice matched to GaN. However, there still exists some question as to what the true lattice matching condition of InAlN to GaN is due to discrepancies in the literature values of lattice parameters of the InN binary, and of the InAlN bowing parameters. We used the gate lag measurement as a supplementary technique to verify lattice matching to the underlying GaN, as we expect the strain in layers one source of lag, associated with piezoelectric charge at the surface. We observe very low lag for nearly lattice matched barrier and barriers under tensile strain, and a marked increase as the composition deviates from the lattice matched condition toward compressively strained layers. Additionally, FETs fabricated on a nearly lattice matched InAlN layer boasted a maximum drain current of over 1.5A/mm and ~2.0A/mm and transconductances of ~275mS/mm and ~300mS/mm at DC and in pulsed modes, respectively, and a cutoff frequency of 15.9GHz (an fT*LG product of 10.3) for a gate length of 0.65μm.
- 7 January 2010
- Published by Wiley in Physica Status Solidi (a)
- Vol. 207 (1) , 211-216
Effect of lattice mismatch on gate lag in high quality InAlN/AlN/GaN HFET structures
Grown lattice matched to GaN, InAlN‐based heterojunction field effect transistors (HFETs) are promising due to the relatively large band discontinuity at the interface and lack of misfit strain. Despite the recent progress in the growth, there still exists some questions as to the true lattice matching condition of InAlN to GaN due to discrepancies in the value of the lattice parameters of the InN binary, as well as the literature value of the InAlN bowing parameters. In order to address this, we used the gate lag as a supplementary measurement to verify lattice matching to the underlying GaN, as strain‐free layers would not have piezoelectric charge at the surface, which would be one source of lag. We observe very low lag for a nearly lattice matched barrier, and a marked increase as the composition deviates from the lattice matched condition. Additionally, FETs fabricated on a nearly matched layer boast a maximum drain current of over 1.5 and ∼2.0 A/mm and transconductances of ∼275 and ∼300 mS/mm at DC and in pulsed modes, respectively, and a cutoff frequency of 15.9 GHz (an fT*LG product of 10.3) for a gate length of 0.65 µm.
- 7 January 2010
- Published by Wiley in Physica Status Solidi (a)
- Vol. 207 (1) , 211-216
Effect of lattice mismatch on gate lag in high quality InAlN/AlN/GaN HFET structures
Grown lattice matched to GaN, InAlN‐based heterojunction field effect transistors (HFETs) are promising due to the relatively large band discontinuity at the interface and lack of misfit strain. Despite the recent progress in the growth, there still exists some questions as to the true lattice matching condition of InAlN to GaN due to discrepancies in the value of the lattice parameters of the InN binary, as well as the literature value of the InAlN bowing parameters. In order to address this, we used the gate lag as a supplementary measurement to verify lattice matching to the underlying GaN, as strain‐free layers would not have piezoelectric charge at the surface, which would be one source of lag. We observe very low lag for a nearly lattice matched barrier, and a marked increase as the composition deviates from the lattice matched condition. Additionally, FETs fabricated on a nearly matched layer boast a maximum drain current of over 1.5 and ∼2.0 A/mm and transconductances of ∼275 and ∼300 mS/mm at DC and in pulsed modes, respectively, and a cutoff frequency of 15.9 GHz (an fT*LG product of 10.3) for a gate length of 0.65 µm.
- 30 November 2009
- Published by AIP Publishing in Applied Physics Letters
- Vol. 95 (22) , 223504
Degradation in InAlN/GaN-based heterostructure field effect transistors: Role of hot phonons
We report on high electric field stress measurements at room temperature on InAlN/AlN/GaN heterostructure field effect transistor structures. The degradation rate as a function of the average electron density in the GaN channel (as determined by gated Hall bar measurements for the particular gate biases used), has a minimum for electron densities around , and tends to follow the hot phonon lifetime dependence on electron density. The observations are consistent with the buildup of hot longitudinal optical phonons and their ultrafast decay at about the same electron density in the GaN channel. In part because they have negligible group velocity, the build up of these hot phonons causes local heating, unless they decay rapidly to longitudinal acoustic phonons, and this is likely to cause defect generation which is expected to be aggravated by existing defects. These findings call for modified approaches in modeling device degradation.- 30 November 2009
- Published by AIP Publishing in Applied Physics Letters
- Vol. 95 (22) , 223504
Degradation in InAlN/GaN-based heterostructure field effect transistors: Role of hot phonons
We report on high electric field stress measurements at room temperature on InAlN/AlN/GaN heterostructure field effect transistor structures. The degradation rate as a function of the average electron density in the GaN channel (as determined by gated Hall bar measurements for the particular gate biases used), has a minimum for electron densities around , and tends to follow the hot phonon lifetime dependence on electron density. The observations are consistent with the buildup of hot longitudinal optical phonons and their ultrafast decay at about the same electron density in the GaN channel. In part because they have negligible group velocity, the build up of these hot phonons causes local heating, unless they decay rapidly to longitudinal acoustic phonons, and this is likely to cause defect generation which is expected to be aggravated by existing defects. These findings call for modified approaches in modeling device degradation.