Tulin Bali
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tulin Bali has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Erdem Cuce
Department of Mechanical Engineering, Faculty of Engineering, Istanbul Aydin University, Istanbul, Turkey
3 shared publications Betul Ayhan Sarac
2 shared publicationsPinar Mert Cuce
2 shared publicationsTeoman Ayhan
2 shared publicationsBekir Karlık
1 shared publicationBetül Ayhan Saraç
Department of Mechanical Engineering, Karadeniz Technical University, Trabzon 61080, Turkey
1 shared publication
Latest Publications
- 23 August 2018
- Published by Springer Nature
- p. 1101-1109
Design and Economic Analysis of Photovoltaic Systems in Different Cities of Turkey
- 23 August 2018
- Published by Springer Nature
- p. 1101-1109
Design and Economic Analysis of Photovoltaic Systems in Different Cities of Turkey
- 1 August 2017
- Published by Elsevier in Energy Conversion and Management
- Vol. 146, 205-216
An accurate model for photovoltaic (PV) modules to determine electrical characteristics and thermodynamic performance parameters
- 1 August 2017
- Published by Elsevier in Energy Conversion and Management
- Vol. 146, 205-216
An accurate model for photovoltaic (PV) modules to determine electrical characteristics and thermodynamic performance parameters
- 1 September 2014
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 76, 385-392
Conjugate heat transfer in a duct with an axially varying heat flux
- 1 September 2014
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 76, 385-392
Conjugate heat transfer in a duct with an axially varying heat flux
- 1 April 2014
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 53, 174-179
Experimental investigation of decaying swirl flow through a circular pipe for binary combination of vortex generators
- 1 April 2014
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 53, 174-179
Experimental investigation of decaying swirl flow through a circular pipe for binary combination of vortex generators
- Top Cited Papers
- 1 November 2013
- Published by Elsevier in Applied Energy
- Vol. 111, 374-382
An experimental analysis of illumination intensity and temperature dependency of photovoltaic cell parameters
- 1 November 2013
- Published by Elsevier in Applied Energy
- Vol. 111, 374-382
Top Cited PapersAn experimental analysis of illumination intensity and temperature dependency of photovoltaic cell parameters
- Open Access
- 2 September 2011
- Published by Oxford University Press (OUP) in International Journal of Low-Carbon Technologies
- Vol. 6 (4) , 299-308
Effects of passive cooling on performance of silicon photovoltaic cells
In this study, an experimental research concerning the effects of passive cooling on performance parameters of silicon solar cells was presented. An aluminum heat sink was used in order to dissipate waste heat from a photovoltaic (PV) cell. Dimensions of the heat sink were determined considering the results of a steady-state heat transfer analysis. The experiments were carried out for different ambient temperatures and various illumination intensities up to 1 sun under solar simulator. Experimental results indicate that energy, exergy and power conversion efficiency of the PV cell considerably increase with the proposed cooling technique. An increase of ∼20% in power output of the PV cell is achieved at 800 W/m2 radiation condition. Maximum level of cooling is observed for the intensity level of 600 W/m2. Performance of PV cells both with and without fins increases with decreasing ambient temperature.
- 2 September 2011
- Published by Oxford University Press (OUP) in International Journal of Low-Carbon Technologies
- Vol. 6 (4) , 299-308
Open AccessEffects of passive cooling on performance of silicon photovoltaic cells
In this study, an experimental research concerning the effects of passive cooling on performance parameters of silicon solar cells was presented. An aluminum heat sink was used in order to dissipate waste heat from a photovoltaic (PV) cell. Dimensions of the heat sink were determined considering the results of a steady-state heat transfer analysis. The experiments were carried out for different ambient temperatures and various illumination intensities up to 1 sun under solar simulator. Experimental results indicate that energy, exergy and power conversion efficiency of the PV cell considerably increase with the proposed cooling technique. An increase of ∼20% in power output of the PV cell is achieved at 800 W/m2 radiation condition. Maximum level of cooling is observed for the intensity level of 600 W/m2. Performance of PV cells both with and without fins increases with decreasing ambient temperature.
- 1 January 2008
- Published by Inderscience Publishers in International Journal of Exergy
- Vol. 5 (1) , 64
Exergy analysis of heat transfer in a turbulent pipe flow by a decaying swirl generator
In this study, heat-transfer and pressure-drop characteristics of a decaying swirl flow in a horizontal pipe are investigated experimentally. The decaying swirl flow is produced by the insertion of swirl generators with propeller-type geometry, a kind of passive heat enhancement tools. Three different positions of the swirl generator in the axial direction are examined: at the inlet (x = 0), x = L/4 and x = L/2. For each position, the effects of the vane angle about the core of the insert device and the number of vanes attached circumferentially to the device on heat transfer and pressure drop are studied. Experiments are conducted at Reynolds numbers ranging from 5000 to 30,000. The optimum geometry is determined according to the exergy analysis and the performance evaluation method used.
- 1 January 2008
- Published by Inderscience Publishers in International Journal of Exergy
- Vol. 5 (1) , 64
Exergy analysis of heat transfer in a turbulent pipe flow by a decaying swirl generator
In this study, heat-transfer and pressure-drop characteristics of a decaying swirl flow in a horizontal pipe are investigated experimentally. The decaying swirl flow is produced by the insertion of swirl generators with propeller-type geometry, a kind of passive heat enhancement tools. Three different positions of the swirl generator in the axial direction are examined: at the inlet (x = 0), x = L/4 and x = L/2. For each position, the effects of the vane angle about the core of the insert device and the number of vanes attached circumferentially to the device on heat transfer and pressure drop are studied. Experiments are conducted at Reynolds numbers ranging from 5000 to 30,000. The optimum geometry is determined according to the exergy analysis and the performance evaluation method used.
- 6 November 2007
- Published by Emerald Publishing in International Journal of Numerical Methods for Heat & Fluid Flow
- Vol. 17 (8) , 788-798
Neural network methodology for heat transfer enhancement data
Purpose: The purpose of this paper is to study experimentally enhancement of heat transfer in a tube with axial swirling‐flow promoters. The geometric features of flow geometry to improve heat transfer can be selected in order to yield the maximum opposite reduction in heat exchange flow irreversibility by using exergy‐destruction method. The paper seeks to illustrate the use of neural network approach to analyze heat transfer enhancement data for further study in the scope of the experimental program.Design/methodology/approach: For this purpose, 402 experimental measurements are collected. About 225 of those are used as training data for neural networks, the rest is used for testing. Then, these testing results of artificial neural network (ANN) and experimental data are compared. A formula for presenting exergy loses in a tubular heat exchanger is derived first and then the thermodynamic optimum instead of economic optimum is found by minimizing the exergy losses in the system.Findings: Results from all configurations studied show that the heat transfer rate of the heated increases when the swirling‐flow promoter is inserted. From the heat transfer improvement number defined, it is observed that about 100 percent increase in heat transfer rate and five times increase in the pressure drop can be achieved under the condition of constant flow for the single promoter which has three blades, its blade angle is 30° and its location is in the middle of the tube length.Research limitations/implications: The back‐propagation (BP) algorithm was selected as the neural network algorithm, which uses the generalized delta learning rule. The training time of BP algorithm is considerably long. However, the testing of our neural network is real‐time.Practical implications: The experimental setup is established to collect the experimental data. It consists of an entrance region, test region (heat exchanger and steam generator), and, flow measurement and control. Also, a software program of neural networks trained BP is written by using Pascal high‐level languages.Originality/value: An alternative and new approach is proposed in the paper to find optimum flow geometry for a pipe flow with an axial swirling‐flow promoter inserts. It is too difficult to predict the response of a complex physical system that cannot be easily modeled mathematically. The result thus obtained compare well with experimental results, but the computational effort of the ANN and time required in the analysis is much faster as compared. These results show that the ANN can be used efficiently for prediction.
- 6 November 2007
- Published by Emerald Publishing in International Journal of Numerical Methods for Heat & Fluid Flow
- Vol. 17 (8) , 788-798
Neural network methodology for heat transfer enhancement data
Purpose: The purpose of this paper is to study experimentally enhancement of heat transfer in a tube with axial swirling‐flow promoters. The geometric features of flow geometry to improve heat transfer can be selected in order to yield the maximum opposite reduction in heat exchange flow irreversibility by using exergy‐destruction method. The paper seeks to illustrate the use of neural network approach to analyze heat transfer enhancement data for further study in the scope of the experimental program.Design/methodology/approach: For this purpose, 402 experimental measurements are collected. About 225 of those are used as training data for neural networks, the rest is used for testing. Then, these testing results of artificial neural network (ANN) and experimental data are compared. A formula for presenting exergy loses in a tubular heat exchanger is derived first and then the thermodynamic optimum instead of economic optimum is found by minimizing the exergy losses in the system.Findings: Results from all configurations studied show that the heat transfer rate of the heated increases when the swirling‐flow promoter is inserted. From the heat transfer improvement number defined, it is observed that about 100 percent increase in heat transfer rate and five times increase in the pressure drop can be achieved under the condition of constant flow for the single promoter which has three blades, its blade angle is 30° and its location is in the middle of the tube length.Research limitations/implications: The back‐propagation (BP) algorithm was selected as the neural network algorithm, which uses the generalized delta learning rule. The training time of BP algorithm is considerably long. However, the testing of our neural network is real‐time.Practical implications: The experimental setup is established to collect the experimental data. It consists of an entrance region, test region (heat exchanger and steam generator), and, flow measurement and control. Also, a software program of neural networks trained BP is written by using Pascal high‐level languages.Originality/value: An alternative and new approach is proposed in the paper to find optimum flow geometry for a pipe flow with an axial swirling‐flow promoter inserts. It is too difficult to predict the response of a complex physical system that cannot be easily modeled mathematically. The result thus obtained compare well with experimental results, but the computational effort of the ANN and time required in the analysis is much faster as compared. These results show that the ANN can be used efficiently for prediction.
- 1 October 2007
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 32 (1) , 158-165
An experimental study on heat transfer and pressure drop characteristics of decaying swirl flow through a circular pipe with a vortex generator
- 1 October 2007
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 32 (1) , 158-165
An experimental study on heat transfer and pressure drop characteristics of decaying swirl flow through a circular pipe with a vortex generator
- 1 January 1999
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 26 (1) , 13-22
Experimental investigation of propeller type swirl generator for a circular pipe flow
- 1 January 1999
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 26 (1) , 13-22
Experimental investigation of propeller type swirl generator for a circular pipe flow