Ulker Asli Guler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ulker Asli Guler has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Batoul Sarraj
Mühendislik Fakültesi Sivas Cumhuriyet Üniversitesi Çevre
1 shared publicationHatice Doğan
Mühendislik Fakültesi Sivas Cumhuriyet Üniversitesi Kimya Mühendisliği Bölümü 2
1 shared publication- Mehtap Ersan
Engineering Faculty, Department of Chemical Engineering, Cumhuriyet University, Sivas 58140, Turkey, Tel. +90 0346 219 10/2243; Fax: +90 346 219 11 77
1 shared publication Mehtap Erşan
1 shared publicationMeltem Sarioglu
Engineering Faculty, Department of Environmental Engineering, Cumhuriyet University, Sivas 58140, Turkey, Tel. +90 346 219 10 10 1295, Fax: +90 346 219 11 77
1 shared publication- Meltem Sarıoğlu (Cebeci)
Cumhuriyet Univ, Dept Environm Engn, TR-58000 Sivas, Turkey
1 shared publication
Latest Publications
- Open Access
- 29 January 2020
- Published by Omer Halisdemir Universitesi Muhendislik Bilimleri Dergisi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 9 (1) , 114-127
KOLEMANİT DESTEKLİ nZVI KULLANILARAK SULU ÇÖZELTİLERDEN METİLEN MAVİSİNİN GİDERİMİ
Bu çalışmada, kolemanit destekli nZVI (K-nZVI) kullanılarak metilen mavisinin adsorpsiyonprosesiyle giderimi araştırılmıştır. Yapılan çalışmada öncelikle kolemanit destekli nZVI sentezlenmiştir. Sentezlenen bu yeni materyal ile sulu çözeltilerden metilen mavisi giderimini etkileyen çözelti pH değeri, K-nZV miktarı, temas süresi, sıcaklık ve başlangıç boya konsantrasyonu gibi adsorpsiyon parametrelerinde çalışılmıştır. Metilen mavisinin K-nZVI ile adsorpsiyonunun, Freundlich izoterm modeline ve yalancı ikinci dereceden kinetiğe daha uygun olduğu belirlenmiştir. Minitab 18 (trial) deneysel regrasyon analizinin sonuçlarına bakılarak verilerin optimizasyonu desteklenmiştir. Maksimum adsorpsiyon giderim verimi pH 4’te 5 g/L K-nZVI miktarı ile 120 dk temas süresi sonunda %90,78 olarak elde edilmiştir. Ayrıca elde edilen optimum koşullarda gerçek tekstil endüstrisi atıksuyu yapılan renk giderim çalışmasında da %94,48 oranında bir giderim verimi elde edilmiştir. Sonuç olarak K-nZVI’nın metilen mavisi gibi katyonik boyaların gideriminde yeni ekonomik bir adsorbent olarak kullanılabileceği sonucuna varılmıştır.
- 29 January 2020
- Published by Omer Halisdemir Universitesi Muhendislik Bilimleri Dergisi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 9 (1) , 114-127
Open AccessKOLEMANİT DESTEKLİ nZVI KULLANILARAK SULU ÇÖZELTİLERDEN METİLEN MAVİSİNİN GİDERİMİ
Bu çalışmada, kolemanit destekli nZVI (K-nZVI) kullanılarak metilen mavisinin adsorpsiyonprosesiyle giderimi araştırılmıştır. Yapılan çalışmada öncelikle kolemanit destekli nZVI sentezlenmiştir. Sentezlenen bu yeni materyal ile sulu çözeltilerden metilen mavisi giderimini etkileyen çözelti pH değeri, K-nZV miktarı, temas süresi, sıcaklık ve başlangıç boya konsantrasyonu gibi adsorpsiyon parametrelerinde çalışılmıştır. Metilen mavisinin K-nZVI ile adsorpsiyonunun, Freundlich izoterm modeline ve yalancı ikinci dereceden kinetiğe daha uygun olduğu belirlenmiştir. Minitab 18 (trial) deneysel regrasyon analizinin sonuçlarına bakılarak verilerin optimizasyonu desteklenmiştir. Maksimum adsorpsiyon giderim verimi pH 4’te 5 g/L K-nZVI miktarı ile 120 dk temas süresi sonunda %90,78 olarak elde edilmiştir. Ayrıca elde edilen optimum koşullarda gerçek tekstil endüstrisi atıksuyu yapılan renk giderim çalışmasında da %94,48 oranında bir giderim verimi elde edilmiştir. Sonuç olarak K-nZVI’nın metilen mavisi gibi katyonik boyaların gideriminde yeni ekonomik bir adsorbent olarak kullanılabileceği sonucuna varılmıştır.
- Open Access
- 1 February 2018
- Published by Elsevier in Desalination and Water Treatment
- Vol. 106, 292-304
Batch and fixed-bed column adsorption of crystal violet and safranin by zero-valent iron (nZVI) and nZVI-modified S. cerevisiae
- 1 February 2018
- Published by Elsevier in Desalination and Water Treatment
- Vol. 106, 292-304
Open AccessBatch and fixed-bed column adsorption of crystal violet and safranin by zero-valent iron (nZVI) and nZVI-modified S. cerevisiae
- Open Access
- 28 November 2017
- Published by Vilnius Gediminas Technical University in Journal of Environmental Engineering and Landscape Management
- Vol. 25 (3) , 223-233
REMOVAL OF TETRACYCLINE FROM AQUEOUS SOLUTIONS USING NANOSCALE ZERO VALENT IRON AND FUNCTIONAL PUMICE MODIFIED NANOSCALE ZERO VALENT IRON
Nanoscale zero valent iron (nzvi) and functional pumice modified nanoscale zero valent iron (P-nzvi) were successfully synthesized and used for the removal of tetracycline (TC). These materials were characterized by SEM, TEM, XRD, FTIR, BET. Different factors such as the mass ratio, dosage of adsorbent, ph, initial TC concentration and temperature were investigated. Based on these results; a possible removal mechanism was proposed including TC adsorption and TC reduction via oxidation of Fe0 to Fe3+. In addition, isotherm and thermodynamic parameters were applied to the equilibrium data. The maximum adsorption capacity of TC by nzvi and P-nzvi was 105.46 mg/g and 115.13 mg/g, respectively. Adsorption and reduction kinetics were examined for the TC removal process. The pseudo-second-order model and pseudo-first-order model was observed for adsorption and reduction process, respectively. Finally, more than 90% of TC from aqueous solutions was removed by nzvi and P-nzvi.
- 28 November 2017
- Published by Vilnius Gediminas Technical University in Journal of Environmental Engineering and Landscape Management
- Vol. 25 (3) , 223-233
Open AccessREMOVAL OF TETRACYCLINE FROM AQUEOUS SOLUTIONS USING NANOSCALE ZERO VALENT IRON AND FUNCTIONAL PUMICE MODIFIED NANOSCALE ZERO VALENT IRON
Nanoscale zero valent iron (nzvi) and functional pumice modified nanoscale zero valent iron (P-nzvi) were successfully synthesized and used for the removal of tetracycline (TC). These materials were characterized by SEM, TEM, XRD, FTIR, BET. Different factors such as the mass ratio, dosage of adsorbent, ph, initial TC concentration and temperature were investigated. Based on these results; a possible removal mechanism was proposed including TC adsorption and TC reduction via oxidation of Fe0 to Fe3+. In addition, isotherm and thermodynamic parameters were applied to the equilibrium data. The maximum adsorption capacity of TC by nzvi and P-nzvi was 105.46 mg/g and 115.13 mg/g, respectively. Adsorption and reduction kinetics were examined for the TC removal process. The pseudo-second-order model and pseudo-first-order model was observed for adsorption and reduction process, respectively. Finally, more than 90% of TC from aqueous solutions was removed by nzvi and P-nzvi.
- Open Access
- 1 April 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (16) , 7196-7208
S. cerevisiae cells modified with nZVI: a novel magnetic biosorbent for nickel removal from aqueous solutions
The present study was conducted to evaluate the applicability of S. cerevisiae cells modified with nZVI (magnetic biosorbent) for the Ni(II) ions removal from aqueous solutions. This composite was synthesized in ethanol using a borohydride reduction method in atmospheric conditions and characterized by FTIR, XRD, and SEM analyses. Batch experiments were examined the effects of initial solution pH, magnetic biosorbent amount, contact time, initial Ni(II) concentration, and temperature. Langmuir, Freundlich, Dubinin–Radushkevich, and Temkin isotherm models were applied to the equilibrium data. The maximum biosorption capacity of the magnetic biosorbent was found to be relatively high (54.23 mg/g). The reductive power of the Fe0 and functional groups on the yeast cell surface contributed to the removal of Ni(II) ions. The kinetics data were best described by the pseudo-second-order kinetics model. Thermodynamics parameters were calculated from the experimental data. Ni(II) removal onto magnetic biosorbent was favorable, physicochemical in nature. Also, the Ni(II) removal onto magnetic biosorbent decreased with increasing in Na concentration in aqueous solutions. The results of this study suggest that the magnetic biosorbent is effective for Ni(II) removal from aqueous solutions.
- 1 April 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (16) , 7196-7208
Open AccessS. cerevisiae cells modified with nZVI: a novel magnetic biosorbent for nickel removal from aqueous solutions
The present study was conducted to evaluate the applicability of S. cerevisiae cells modified with nZVI (magnetic biosorbent) for the Ni(II) ions removal from aqueous solutions. This composite was synthesized in ethanol using a borohydride reduction method in atmospheric conditions and characterized by FTIR, XRD, and SEM analyses. Batch experiments were examined the effects of initial solution pH, magnetic biosorbent amount, contact time, initial Ni(II) concentration, and temperature. Langmuir, Freundlich, Dubinin–Radushkevich, and Temkin isotherm models were applied to the equilibrium data. The maximum biosorption capacity of the magnetic biosorbent was found to be relatively high (54.23 mg/g). The reductive power of the Fe0 and functional groups on the yeast cell surface contributed to the removal of Ni(II) ions. The kinetics data were best described by the pseudo-second-order kinetics model. Thermodynamics parameters were calculated from the experimental data. Ni(II) removal onto magnetic biosorbent was favorable, physicochemical in nature. Also, the Ni(II) removal onto magnetic biosorbent decreased with increasing in Na concentration in aqueous solutions. The results of this study suggest that the magnetic biosorbent is effective for Ni(II) removal from aqueous solutions.
- Open Access
- 1 July 2014
- Published by Elsevier in Desalination and Water Treatment
- Vol. 52 (25-27) , 4871-4888
Mono and binary component biosorption of Cu(II), Ni(II), and Methylene Blue onto raw and pretreated S. cerevisiae: equilibrium and kinetics
The mono and binary biosorption of Cu(II) ions, Ni(II) ions, and Methylene Blue dye onto raw and pretreated S. cerevisiae was investigated in a batch system. The biosorption mechanism was characterized by FT-IR, XRD, and SEM analyses. The effects of pH, contact time, initial pollutant concentration, temperature, and biosorbent dosage on the biosorption studies were determined. The experimental data were analyzed by Langmuir, Freundlich, and Dubinin–Radushkevich isotherm models. The results were compatible with both Langmuir and Freundlich isotherm models. The mean free energy (E) values indicated that the biosorption of Cu(II), Ni(II), and Methylene Blue onto raw and pretreated S. cerevisiae took place by chemical-ion exchange. Kinetic data fitted well into the pseudo-second-order model. The calculated thermodynamic parameters (ΔH, ΔS, and ΔG) showed that the biosorption of Cu(II), Ni(II), and Methylene Blue onto raw and pretreated S. cerevisiae was exothermic and spontaneous. Desorption, ion selectivity, and the effect of ionic strength (NaCl) studies were also conducted. Competitive biosorption of binary mixtures of Cu(II), Ni(II), and MB was investigated in terms of biosorption capacity and found that the biosorption capacity of biosorbent decreased with increasing competing pollutant concentration.
- 1 July 2014
- Published by Elsevier in Desalination and Water Treatment
- Vol. 52 (25-27) , 4871-4888
Open AccessMono and binary component biosorption of Cu(II), Ni(II), and Methylene Blue onto raw and pretreated S. cerevisiae: equilibrium and kinetics
The mono and binary biosorption of Cu(II) ions, Ni(II) ions, and Methylene Blue dye onto raw and pretreated S. cerevisiae was investigated in a batch system. The biosorption mechanism was characterized by FT-IR, XRD, and SEM analyses. The effects of pH, contact time, initial pollutant concentration, temperature, and biosorbent dosage on the biosorption studies were determined. The experimental data were analyzed by Langmuir, Freundlich, and Dubinin–Radushkevich isotherm models. The results were compatible with both Langmuir and Freundlich isotherm models. The mean free energy (E) values indicated that the biosorption of Cu(II), Ni(II), and Methylene Blue onto raw and pretreated S. cerevisiae took place by chemical-ion exchange. Kinetic data fitted well into the pseudo-second-order model. The calculated thermodynamic parameters (ΔH, ΔS, and ΔG) showed that the biosorption of Cu(II), Ni(II), and Methylene Blue onto raw and pretreated S. cerevisiae was exothermic and spontaneous. Desorption, ion selectivity, and the effect of ionic strength (NaCl) studies were also conducted. Competitive biosorption of binary mixtures of Cu(II), Ni(II), and MB was investigated in terms of biosorption capacity and found that the biosorption capacity of biosorbent decreased with increasing competing pollutant concentration.
- Open Access
- 1 May 2014
- Published by Springer Nature in Journal of Environmental Health Science and Engineering
- Vol. 12 (1) , 79
Removal of tetracycline from wastewater using pumice stone: equilibrium, kinetic and thermodynamic studies
In this study, pumice stone was used for the removal of tetracyline (TC) from aqueous solutions. It was characterized by XRD, FT-IR, SEM and BET analyses. Cation exchange capacity of pumice stone was found to be 9.9 meq/100 g. Effect of various parameters such as solution pH (2–11), adsorbent dosage (0.5-10 g/L), contact time (2.5-120 min), initial TC concentration (5–300 mg/L) and temperature (20–50°C) on TC adsorption onto pumice was investigated. Also the adsorption of TC on pumice stone was studied as a function of Na+ and Cu2+ cations changing pH from 2 to 11 using batch experiments. The best removal efficiency performance was exhibited at adsorbent dosage 10 g/L, pH 3, contact time 120 min. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) isotherm models were applied to the equilibrium data. The result has shown that the adsorption was favorable, physicochemical in nature and agrees well with Langmuir and Freundlich models. The maximum Langmuir adsorption capacity was found to be 20.02 mg/g. The adsorption behavior of TC on pumices stone was fitted well in the pseudo-second order kinetics model. Thermodynamic parameters calculated from the adsorption data at different temperature showed that the adsorption reaction was feasible, spontaneous and exothermic.
- 1 May 2014
- Published by Springer Nature in Journal of Environmental Health Science and Engineering
- Vol. 12 (1) , 79
Open AccessRemoval of tetracycline from wastewater using pumice stone: equilibrium, kinetic and thermodynamic studies
In this study, pumice stone was used for the removal of tetracyline (TC) from aqueous solutions. It was characterized by XRD, FT-IR, SEM and BET analyses. Cation exchange capacity of pumice stone was found to be 9.9 meq/100 g. Effect of various parameters such as solution pH (2–11), adsorbent dosage (0.5-10 g/L), contact time (2.5-120 min), initial TC concentration (5–300 mg/L) and temperature (20–50°C) on TC adsorption onto pumice was investigated. Also the adsorption of TC on pumice stone was studied as a function of Na+ and Cu2+ cations changing pH from 2 to 11 using batch experiments. The best removal efficiency performance was exhibited at adsorbent dosage 10 g/L, pH 3, contact time 120 min. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) isotherm models were applied to the equilibrium data. The result has shown that the adsorption was favorable, physicochemical in nature and agrees well with Langmuir and Freundlich models. The maximum Langmuir adsorption capacity was found to be 20.02 mg/g. The adsorption behavior of TC on pumices stone was fitted well in the pseudo-second order kinetics model. Thermodynamic parameters calculated from the adsorption data at different temperature showed that the adsorption reaction was feasible, spontaneous and exothermic.