Patrick Rambaud
Patrick Rambaud has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Jean-Marie Buchlin
Naval and Oceanic Engineering Department, University of A Coruña, Ferrol, Spain
3 shared publications M. L. Riethmuller
Von Karman Institute for Fluid Dynamics
2 shared publicationsA. Stitou
Von Karman Institute for Fluid Dynamics
1 shared publicationC. Schram
Von Karman Institute for Fluid Dynamics, Rhode-St-Genese, Belgium
1 shared publicationDilek Yildiz
Von Karman Institute for Fluid Dynamics, Rhode-Saint-Genese, Belgium
1 shared publicationE. Özsoy
Von Karman Institute for Fluid Dynamics
1 shared publication
Latest Publications
- 5 December 2012
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 135 (1) , 011305
Flowforce in a Safety Relief Valve Under Incompressible, Compressible, and Two-Phase Flow Conditions (PVP-2011-57896)
The use of relief valves is crucial for the safety of power plants. Indeed, these valves, simple but robust in their design, provide the ultimate protection when all other safety systems are inadequate. This study is focused on valve opening characteristics which can be studied through the determination of flowforces applied on the valve disk. A spring-loaded safety relief valve (SRV) (1½ in. G 3 in.) and its transparent model are tested under static conditions. The spring is removed and the forces, exerted at the valve disk for different inlet pressures and lift positions, are measured in compressible, incompressible, and two-phase flows. Results indicate that even for relatively small qualities (i.e., 5–10%), two-phase mixtures approach compressible flow behavior (especially for the higher lifts) in terms of disk force. Additionally, an inverse flowforce of air and water is noticed above a certain value of valve lift. Numerical simulations with a commercial computation fluid dynamics (CFD) code are performed in a 2D axisymmetric model of the valve for validation purposes. The main motivation of these computations is to obtain the qualitative physical explanation of this phenomenon revealing the displacement of the sonic line which occurs in air flow simulations. Finally, the importance of precise adjustment of the valve ring (in the smallest valve opening) for its optimal use is stressed by quantitative analysis using CFD simulations.
- 5 December 2012
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 135 (1) , 011305
Flowforce in a Safety Relief Valve Under Incompressible, Compressible, and Two-Phase Flow Conditions (PVP-2011-57896)
The use of relief valves is crucial for the safety of power plants. Indeed, these valves, simple but robust in their design, provide the ultimate protection when all other safety systems are inadequate. This study is focused on valve opening characteristics which can be studied through the determination of flowforces applied on the valve disk. A spring-loaded safety relief valve (SRV) (1½ in. G 3 in.) and its transparent model are tested under static conditions. The spring is removed and the forces, exerted at the valve disk for different inlet pressures and lift positions, are measured in compressible, incompressible, and two-phase flows. Results indicate that even for relatively small qualities (i.e., 5–10%), two-phase mixtures approach compressible flow behavior (especially for the higher lifts) in terms of disk force. Additionally, an inverse flowforce of air and water is noticed above a certain value of valve lift. Numerical simulations with a commercial computation fluid dynamics (CFD) code are performed in a 2D axisymmetric model of the valve for validation purposes. The main motivation of these computations is to obtain the qualitative physical explanation of this phenomenon revealing the displacement of the sonic line which occurs in air flow simulations. Finally, the importance of precise adjustment of the valve ring (in the smallest valve opening) for its optimal use is stressed by quantitative analysis using CFD simulations.
- 1 January 2008
- Published by ASME International
- p. 241-247
LES-PIV Comparison for Air Flow in a Simplified Cowl-Box
A single-phase Large Eddy Simulation is performed in a simplified cowl-box model and compared to PIV data. Indeed, prior to the analysis of the interaction between a turbulent air flow and an interface of liquid, the most accurate description of the 3D flow field is required. Although the qualitative phenomena are correctly rendered (flapping motion of impinging inlet jets), quantitative differences are noticed, mainly due to non satisfactory turbulent boundary condition, which induces an overestimation of the jets core length, and modifies its interaction with the cowl box walls. Nevertheless, a qualitative analysis of the instantaneous flow shows the generation of large coherent vortical structures due to the oscillation of the impinging jets at the bottom wall. The advection of these structures in the cowl-box generates large oscillations of wall shear stress and pressure distribution, which are thought to be of great importance for further two-phase flow simulations.
- 1 January 2008
- Published by ASME International
- p. 241-247
LES-PIV Comparison for Air Flow in a Simplified Cowl-Box
A single-phase Large Eddy Simulation is performed in a simplified cowl-box model and compared to PIV data. Indeed, prior to the analysis of the interaction between a turbulent air flow and an interface of liquid, the most accurate description of the 3D flow field is required. Although the qualitative phenomena are correctly rendered (flapping motion of impinging inlet jets), quantitative differences are noticed, mainly due to non satisfactory turbulent boundary condition, which induces an overestimation of the jets core length, and modifies its interaction with the cowl box walls. Nevertheless, a qualitative analysis of the instantaneous flow shows the generation of large coherent vortical structures due to the oscillation of the impinging jets at the bottom wall. The advection of these structures in the cowl-box generates large oscillations of wall shear stress and pressure distribution, which are thought to be of great importance for further two-phase flow simulations.
- 1 January 2006
- Published by ASME International
- p. 921-930
Characterization of Superheated Liquid Jet Atomisation With Phase Doppler Anemometer (PDA) and High-Speed Imaging
A flashing phenomenon is often met in liquid propulsion of safety fields in industrial environments. This violent evaporation occurs when a liquid finds itself suddenly in a thermodynamic non-equilibrium and becomes superheated. To investigate theoretically the source processes and validate models for design and safety assessments, knowledge of accurate and reliable data such as distribution of droplet size, velocity and temperature in the closest field of flashing occurrence is mandatory. In this present work, an experimental study is undertaken in order to characterize the two-phase jet after a sudden accidental release and aims to quantify the effects of initial conditions such as initial storage pressure, temperature, geometrical effects of the release points etc on the spray characteristics. To fulfil this goal, a laser-based optical technique like Phase Doppler Anemometry (PDA) is used to obtain information for particle diameter and velocity evolution in this harsh environment. Cases for different initial pressures, temperatures and orifice diameters are studied and the droplet size and velocity evolution are presented in function of initial parameters.
- 1 January 2006
- Published by ASME International
- p. 921-930
Characterization of Superheated Liquid Jet Atomisation With Phase Doppler Anemometer (PDA) and High-Speed Imaging
A flashing phenomenon is often met in liquid propulsion of safety fields in industrial environments. This violent evaporation occurs when a liquid finds itself suddenly in a thermodynamic non-equilibrium and becomes superheated. To investigate theoretically the source processes and validate models for design and safety assessments, knowledge of accurate and reliable data such as distribution of droplet size, velocity and temperature in the closest field of flashing occurrence is mandatory. In this present work, an experimental study is undertaken in order to characterize the two-phase jet after a sudden accidental release and aims to quantify the effects of initial conditions such as initial storage pressure, temperature, geometrical effects of the release points etc on the spray characteristics. To fulfil this goal, a laser-based optical technique like Phase Doppler Anemometry (PDA) is used to obtain information for particle diameter and velocity evolution in this harsh environment. Cases for different initial pressures, temperatures and orifice diameters are studied and the droplet size and velocity evolution are presented in function of initial parameters.
- 23 December 2004
- Published by Springer Nature in Experiments in Fluids
- Vol. 38 (2) , 133-145
Vortex characteristics in laminar cavity flow at very low Mach number
- 23 December 2004
- Published by Springer Nature in Experiments in Fluids
- Vol. 38 (2) , 133-145
Vortex characteristics in laminar cavity flow at very low Mach number
- 1 February 2004
- Published by Springer Nature in Experiments in Fluids
- Vol. 36 (2) , 233-245
Wavelet based eddy structure eduction from a backward facing step flow investigated using particle image velocimetry
- 1 February 2004
- Published by Springer Nature in Experiments in Fluids
- Vol. 36 (2) , 233-245
Wavelet based eddy structure eduction from a backward facing step flow investigated using particle image velocimetry