Omer Lacin has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optimization of Smithsonite Ore Solubility with Lactic Acid Leaching Reagent

    by Elif Şahin, Fatih Demir, Ömer Laçin, Fatih Sevim

    In this study, optimum parameters for leaching performance of lactic acid reagent in smithsonite ore were determined using L16 (45) experimental plan in the Taguchi Statistical Method. Since maximum smithsonite ore extraction was desired for the result, Taguchi's 'bigger is better' performance formula was used. In the experiments; parameters affecting dissolution such as temperature, reaction time, particle size, acid concentration and solid/liquid ratio were investigated. When ANOVA analysis was applied to the parameters, it was determined that the most effective parameters according to F values were acid concentration, solid/liquid ratio and particle size, respectively. In addition, it was observed that zinc conversion increased with increasing temperature and decreasing solid/liquid ratio and particle size. The parameter levels that maximized the S/N value were determined to be 30ºC temperature, 0.01 g.mL-1 solid/liquid ratio, 1 M lactic acid concentration,-160.5 µm particle size and 20 min reaction time. Under these conditions, it was found that smithsonite ore was dissolved by 98.85%.


  • Open Access

    Impurity Control in Boric Acid Leaching: A Review of Challenges and Strategies

    by Ö. Laçin, F. Demir

    Boron minerals, which are hydrated borate compounds of alkali and alkaline earth metals such as Na, Ca, and Mg, contain impurities including clay minerals, calcite, dolomite, gypsum, realgar, orpiment, iron oxide, and sulphur. Boric acid, produced from boron minerals, is the most widely used chemical in the industry as it is used as a raw material in the manufacture of various specific boron products. Boron products are among the most commonly utilised materials today, owing to properties such as resistance to chemical effects, light-weight structure, high mechanical strength, and thermal stability. During the production of boric acid, if the impurities in the boron minerals are not controlled due to the different leach reagents used, filtration difficulties will occur in the later stages of the process. Therefore, the purity and yield of boric acid will be adversely affected, and environmental pollution will occur. The most difficult impurities among these are calcium and magnesium. A review of the literature reveals that many leaching studies have been conducted without adequate consideration of such impurities, leading to the aforementioned issues. In studies where impurities were considered, it has been determined that parameters such as reaction time, temperature, solid/liquid ratio, particle size, mixing speed, and acid concentrations significantly influence the presence of calcium and magnesium, as well as the overall quality of boric acid. With this literature review, the remarkable results obtained from many studies on impurities will be compiled into a single article. Thus, it is believed that researchers working on the subject will be greatly facilitated by the information gathered in this review, enabling them to obtain products with higher purity and more environmentally friendly by-products. Graphical Abstract


  • Open Access

    Zinc leaching from smithsonite ore in lactic acid solution: Studies on parametric optimization, kinetic and mechanism

    by Sıla Sadiye Ilhan, Fatih Demir, Omer Lacin, Fatih Sevim

    . The solubility of low-grade zinc ores with a selective leaching environmentally friendly reagent has become a focus of great interest since zinc and its compounds have found wide application. For this purpose, lactic acid was used to investigate the selective leaching kinetics of smithsonite ore obtained from Kayseri region. The effects of particle size (137.5-725 µm), acid concentration (0.5-5 M), solid/liquid ratio (0.5/250-3/250 g mL-1), stirring speed (500-800 rpm) and temperature (40-70 °C) parameters on the smithsonite dissolution rate were experimentally studied. The results obtained show that leaching of about 99.8% of zinc is achieved using 425 µm particle size at a reaction temperature of 70 °C for 45 min reaction time with 2 M lactic acid, the solid/liquid ratio of 1/250 g mL-1 and stirring speed of 600 rpm. The statistical analysis of the experimental data obtained from the parameters revealed that smithsonite dissolution was the surface reaction-controlled with an apparent activation energy of 53.62 kJ.moL-1. The kinetic model describing the process was found as KEY WORDS: Smithsonite, Dissolution kinetics, Lactic acid, Zinc lactate Bull. Chem. Soc. Ethiop. 2023, 37(3), 735-744. DOI: https://dx.doi.org/10.4314/bcse.v37i3.15


  • Open Access

    Malahit Yeşilinin Gideriminde Şeftali Çekirdeği Kabuğu: Karakterizasyon ve Kinetik İnceleme

    by Erbil Kavci, Bünyamin Dönmez, Ali Çi̇çEkçi̇, Ömer Laçi̇n

    Bu araştırmada, adsorbent olarak kullanılan şeftali çekirdeği kabuğu üzerine sulu ortamdaki malahit yeşilinin adsorpsiyonu amaçlanmıştır. Bunun için önce adsorbentin karakterizasyonu incelenmiş ve sonrasında adsorpsiyon prosesini etkileyen parametrelerden faydalanarak uygun bir kinetik model elde edilmiştir. Karakterizasyon çalışmalarında; Taramalı Elektron mikroskobu, Termal Gravimetri/Diferansiyel Taramalı Kalorimetri, Diferansiyel Termal Gravimetri, X-Işını Kırınımı ve Yüzey analizleri yapılmıştır. Termal Gravimetri/Diferansiyel Taramalı Kalorimetri analizleri ile, şeftali çekirdeğinin 25-150°C, 200-380°C ve 380-580°C sıcaklık aralıklarında bozunduğu gözlenmiştir. X-Işını Kırınımı analizleri sonucu ise, adsorbent yapısının amorf bir karaktere sahip olduğunu ortaya koymuştur. Ayrıca, yüzey analizleri ile, adsorbentin yüzey alanı, por hacmi ve ortalama por çapı değerleri belirlenmiştir. Adsorpsiyon prosesinin kinetiğinin belirlenmesi için, yaygın olarak kullanılan modeller incelenmiş ve kinetik modelin yalancı ikinci mertebeye uyduğu tespit edilmiştir. Elde edilen sonuçlar ışığında, endüstriyel anlamda sulu çözeltilerden malahit yeşilinin uzaklaştırılması hususunda şeftali çekirdeği kabuğunun oldukça katkı sağlayacağı söylenebilir.


  • Open Access

    Adsorption Isotherms and Thermodynamics on Peach Kernel Peel of Malahit Green

    by Ali Çi̇çekçi̇, Bünyamin Dönmez, Erbil Kavci, Ömer Laçi̇n

    Tr en Bu çalışmada, malahit yeşilinin ham şeftali çekirdeği kabuğu üzerine yaygın adsorpsiyon izoterm modelleri ve termodinamik analizi incelenmiştir. Elde edilen sonuçlardan, korelasyon katsayılarına göre en uygun modelin Freundlich izotermi olduğu belirlenmiştir. Ayrıca, hesaplanan n değerinin 1’den büyük olması adsorbentin heterojen bir yüzeye sahip olduğunu göstermiştir. Langmuir izoterm modelinde ise, maksimum adsorpsiyon kapasitesi 8.19 mg.g-1 olarak hesaplanmıştır. Ayrıca, termodinamik analizlerden, serbest entalpi değişiminin -21.53 kJ.mol-1 ve Gibbs serbest enerji değerinin ise yaklaşık -39 kJ.mol-1 olması, adsorpsiyon prosesinin ekzotermik , fiziksel karakterli ve kendiliğinden yürüdüğünü ortaya koymaktadır. Sonuç olarak, şeftali çekirdeği kabuğunun, sulu çözeltilerdeki malahit yeşilinin uzaklaştırılması hususunda uygun bir adsorbent olarak kullanılabilir. Ayrıca elde edilen izoterm modeli ve termodinamik parametrelerin, endüstriyel olarak malahit yeşilinin giderilmesi prosesine faydalı veriler sağlanacağı söylenebilir. In this study, common adsorption isotherm models and thermodynamic analysis of malachite green on raw peach kernel peel are investigated. From the results obtained, it is determined that the most suitable model according to the correlation coefficients is Freundlich isotherm. In addition, the calculated n value greater than 1 indicates that the adsorbent has a heterogeneous surface. In Langmuir isotherm model, the maximum adsorption capacity is calculated as 8.19 mg.g-1. Also, from the thermodynamic analysis, the free enthalpy change of -21.53 kJ.mol-1 and the Gibbs free energy value of about -39 kJ.mol-1 reveal that the adsorption process is exothermic, physically and spontaneous. As a result, the peach kernel skin can be used as a suitable adsorbent for removing malachite green in aqueous solutions. In addition, it can be said that the isotherm model and thermodynamic parameters obtained will provide useful data for the industrial greenhouse removal process.


  • А kinеtiс аnаlysis fоr prоduсtiоn of саlсium bоrоgluсоnаtе frоm colemanite

    by Fatih Demir, Anas Osamah Ali Al‐Ani, Omer Lacin

    In this paper, the kinetic model of colemanite dissolution in gluconic acid solutions was carried out in a batch reactor. The effects of the particle size, reaction temperature, stirring speed, gluconic acid concentration, and solid/liquid ratio on colemanite dissolution were experimentally studied. The empirical parameters were the gluconic acid concentration (0.05‐0.2 M), the temperature (20‐50°C), the solid/liquid ratio (0.05/500‐1.5/500 g⋅L−1), particle size (193.5‐1000 μm), and stirring speed (400‐700 rpm).The kinetic models for heterogeneous solid‐liquid reactions were used with the dissolution data in evaluating the kinetic. The dissolution of colemanite in gluconic acid solutions was controlled by diffusion through the product layer. The activation energy was found to be 8.39 kJ⋅mol−1. The rate expression associated with the dissolution rate of colemanite depending on the parameters chosen may be summarized as follows:


  • Adsorption capacity, isotherm, kinetic, and thermodynamic studies on adsorption behavior of malachite green onto natural red clay

    by Fatih Sevim, Omer Lacin, Emre Fatih Ediz, Fatih Demir

    The adsorption of Malachite Green onto natural red clay by batch‐adsorption technique is investigated. The effects of initial dye concentration, amount of adsorbent, adsorption time, pH, and temperature are examined. The results of X‐ray diffraction, scanning electron microscopy, Thermogravimetry/Differential Thermal Analysis, Brunauer–Emmett–Teller Surface Area Analysis, and Harkins‐Jura Pore Size ‐ Volume Analysis are used for the characterization of adsorbent. The adsorption capacity, isotherm, kinetics, and equilibrium studies are performed. The maximum adsorption has occurred at pH ranging from 6.0 to 10.0. Therefore, the free pH value of 5.16 is chosen as the constant parameter. The pseudo second order kinetic model is found to be in good agreement with the experimental values obtained. The adsorption equilibrium data are analysed using various adsorption isotherm models and the results show that adsorption behavior fits well to the Freundlich isotherm model. The maximum monolayer adsorption capacity is found to be 84.75 mg/g. From the positive values of ∆Ho and the negative values of ∆Go, it can be said that adsorption processes are carried out with endothermic, physical adsorption, and spontaneous.


  • Open Access

    RADYOAKTIF PERTEKNETAT OKSO ANYONU ADSORPSIYONUNUN TERMODINAMIK ANALIZI

    by Fatih Demir, Omer Lacin, Burak Bastaban

    Tr en Kesikli sistemde çalışılan adsorpsiyon tekniği ile aktif karbon üzerine radyoaktif perteknetat okso anyonu (99mTcO4-)’nun adsorpsiyon termodinamiğinin incelenmesi amaçlanmıştır. Elde edilen verilerden faydalanarak termodinamik parametreler; ∆Ho=0,346 kJ.mol-1, ∆So=0,029 kJ.mol-1, ∆Go= -7,92 (288 K) ile -8,78 (318 K) kJ.mol-1, ∆Hx=0,28 kJ.mol-1ve standart serbest enerji değerinin sıfır olduğu sıcaklık 12 K olarak hesaplanmıştır. Bu bulgular sonucunda adsorpsiyon prosesinin; fiziksel ve endotermik olarak gerçekleştiği ve 12 K’in üzerindeki her sıcaklıkta adsorpsiyonun uygun ve kendiliğinden gerçekleşeceği bulguları elde edilmiştir. Sonuç olarak, belirli bir limitin üzerine çıkıldığında kansere neden olan radyoaktif teknesyumun aktif karbon üzerine adsorpsiyon termodinamik analizinin incelenmesi sonucu elde edilen bulguların endüstriyel çapta kurulacak bir tesis dizaynına katkıda bulunacağı söylenebilir. The aim of this study is to investigate thermodynamics of radioactive pertechnetate okso anion (99mTcO4-) over the active carbon using the adsorption technique in batched systems. According to the obtained results thermodynamic parameters are calculated as ∆Ho=0.346 kJ.mol-1, ∆So=0.029 kJ.mol-1, ∆Go= -7.92 (15oC) ile -8.78 (45oC) kJ.mol-1, ∆Hx=0,28 kJ.mol-1 and also the temperature at which the standart free energy value equals to zero calculated as 12 K. These results indicated that the adsorption process is physical and endothermic and at temparatures over 12 K adsorption will take place spontaneously and favorably. In conclusion, it can be said that the results obtained from the thermodynamic analysis of radioactive technetium (which may cause cancer if the limit is exceeded) over the active carbon can contribute to the design of an industrial facility.