Hermann Riedel
Research Subjects
Hermann Riedel has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Gerhard Maier
Fraunhofer Institute for Mechanics of Materials IWM, Woehlerstrasse 11, 79108 Freiburg, Germany
2 shared publicationsJutta Klöwer
Outokumpu VDM GmbH, Germany
2 shared publicationsTom Walde
Fraunhofer Institute for Mechanics of Materials; Woehlerstr. 11 D-79108 Freiburg Germany
2 shared publications- Aruna Prakash
Department of Materials Science and Engineering, Institute I, Friedrich-Alexander-Universität Erlangen-Nürnberg, Martensstr. 5, Erlangen, Germany
1 shared publication B. Blug
Fraunhofer-Institut für Werkstoffmechanik
1 shared publicationBritta Nieweg
Fraunhofer Institute for Mechanics of Materials IWM, Germany
1 shared publication
Latest Publications
- Open Access
- 17 August 2024
- Published by Elsevier in International Journal of Fatigue
- Vol. 189
Multiple cracking, crack coalescence and fatigue lifetime – Model and experiments on an austenitic steel and on a nickel base alloy
- 17 August 2024
- Published by Elsevier in International Journal of Fatigue
- Vol. 189
Open AccessMultiple cracking, crack coalescence and fatigue lifetime – Model and experiments on an austenitic steel and on a nickel base alloy
- 1 September 2021
- Published by Elsevier in International Journal of Fatigue
- Vol. 150, 106308
A lifetime model for creep-fatigue interaction with applications to the creep resistant steel P92
- 1 September 2021
- Published by Elsevier in International Journal of Fatigue
- Vol. 150, 106308
A lifetime model for creep-fatigue interaction with applications to the creep resistant steel P92
- 1 January 2013
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 30 (1) , 27-35
Cyclic deformation and lifetime of Alloy 617B during thermo-mechanical fatigue
Different heats of the nickel-base Alloy 617B are tested under in-phase and out-of-phase thermo-mechanical fatigue (TMF) conditions at temperatures between 50 and 900 °C. During one of the TMF tests the growth of microcracks is observed using the replica technique. After the tests, some of the specimens are inspected by scanning electron microscopy in order to analyse the prevailing damage mechanisms compared with those observed in isothermal low-cycle fatigue (LCF) tests. In addition, a Chaboche-type model and a fracture-mechanics-based lifetime model are employed to describe the cyclic viscoplastic deformation and fatigue lifetime. The Chaboche model adjusted to isothermal data is found to reasonably predict the cyclic viscoplastic behaviour of thermo-mechanically loaded specimens. Lifetime data of TMF tests fall into a common scatter band with LCF tests at temperatures above 400 °C if the test results are analysed based on the introduced lifetime model.
- 1 January 2013
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 30 (1) , 27-35
Cyclic deformation and lifetime of Alloy 617B during thermo-mechanical fatigue
Different heats of the nickel-base Alloy 617B are tested under in-phase and out-of-phase thermo-mechanical fatigue (TMF) conditions at temperatures between 50 and 900 °C. During one of the TMF tests the growth of microcracks is observed using the replica technique. After the tests, some of the specimens are inspected by scanning electron microscopy in order to analyse the prevailing damage mechanisms compared with those observed in isothermal low-cycle fatigue (LCF) tests. In addition, a Chaboche-type model and a fracture-mechanics-based lifetime model are employed to describe the cyclic viscoplastic deformation and fatigue lifetime. The Chaboche model adjusted to isothermal data is found to reasonably predict the cyclic viscoplastic behaviour of thermo-mechanically loaded specimens. Lifetime data of TMF tests fall into a common scatter band with LCF tests at temperatures above 400 °C if the test results are analysed based on the introduced lifetime model.
- Open Access
- 4 July 2011
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 278, 369-374
Time and Temperature Dependent Cyclic Plasticity and Fatigue Crack Growth of the Nickel-Base Alloy617B – Experiments and Models
Isothermal low cycle fatigue and thermomechanical fatigue tests are performed on Alloy617B in the solution-annealed and stabilized condition at temperatures between room temperature and 900 °C. In addition, the replica technique is applied to study the growth of microcracks. The Chaboche model is found to describe the cyclic viscoplastic behavior of both heats, except the pronounced cyclic hardening in the low-temperature branches of the TMF tests. A lifetime model based on the cyclic crack-tip opening displacement and the cyclic J integral is used to describe the measured lifetimes and crack growth rates. However, the description is not fully consistent, since the data for room temperature and for temperatures above 400 °C fall into two separate scatter bands.
- 4 July 2011
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 278, 369-374
Open AccessTime and Temperature Dependent Cyclic Plasticity and Fatigue Crack Growth of the Nickel-Base Alloy617B – Experiments and Models
Isothermal low cycle fatigue and thermomechanical fatigue tests are performed on Alloy617B in the solution-annealed and stabilized condition at temperatures between room temperature and 900 °C. In addition, the replica technique is applied to study the growth of microcracks. The Chaboche model is found to describe the cyclic viscoplastic behavior of both heats, except the pronounced cyclic hardening in the low-temperature branches of the TMF tests. A lifetime model based on the cyclic crack-tip opening displacement and the cyclic J integral is used to describe the measured lifetimes and crack growth rates. However, the description is not fully consistent, since the data for room temperature and for temperatures above 400 °C fall into two separate scatter bands.
- 1 October 2007
- Published by Wiley in Steel Research International
- Vol. 78 (10-11) , 818-824
The Formation of Edge Cracks during Rolling of Metal Sheet
- 1 October 2007
- Published by Wiley in Steel Research International
- Vol. 78 (10-11) , 818-824
The Formation of Edge Cracks during Rolling of Metal Sheet
- 15 March 2007
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 539-543, 3448-3453
Experimental and Numerical Investigation of Texture Development during Hot Rolling of Magnesium Alloy AZ31
Due to the deformation mechanisms and the typical basal texture rolled magnesium sheets show a significant asymmetry of flow stress in tension and compression. In order to avoid this undesired behavior it is necessary to achieve non-basal texture during rolling, or at least, to reduce the intensity of the basal texture component. The reduction of the anisotropy caused by the basal texture is very important for subsequent forming processes. This project aims at optimizing the hot rolling process with special consideration of texture effects. The development of the model is carried out in close cooperation with the experimental work on magnesium alloy AZ31 .The experimental results are required for the determination of model parameters and for the verification of the model. Deformation-induced texture is described by the visco-plastic self-consistent (VPSC) model of Lebensohn and Tomé. The combination of deformation and recrystallization texture models is applied to hot compression tests on AZ31, and it is found, that the model describes the observed texture and hardening/softening behavior well. In some cases rotation recrystallization occurs in AZ31 which appears to be a possibility to reduce the undesired basal rolling texture.
- 15 March 2007
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 539-543, 3448-3453
Experimental and Numerical Investigation of Texture Development during Hot Rolling of Magnesium Alloy AZ31
Due to the deformation mechanisms and the typical basal texture rolled magnesium sheets show a significant asymmetry of flow stress in tension and compression. In order to avoid this undesired behavior it is necessary to achieve non-basal texture during rolling, or at least, to reduce the intensity of the basal texture component. The reduction of the anisotropy caused by the basal texture is very important for subsequent forming processes. This project aims at optimizing the hot rolling process with special consideration of texture effects. The development of the model is carried out in close cooperation with the experimental work on magnesium alloy AZ31 .The experimental results are required for the determination of model parameters and for the verification of the model. Deformation-induced texture is described by the visco-plastic self-consistent (VPSC) model of Lebensohn and Tomé. The combination of deformation and recrystallization texture models is applied to hot compression tests on AZ31, and it is found, that the model describes the observed texture and hardening/softening behavior well. In some cases rotation recrystallization occurs in AZ31 which appears to be a possibility to reduce the undesired basal rolling texture.
- 1 September 2006
- Published by Wiley in Steel Research International
- Vol. 77 (9) , 741-746
Finite-Element Implementation of a Self-consistent Texture Model with a Hardening Law Based on Dislocation Densities
- 1 September 2006
- Published by Wiley in Steel Research International
- Vol. 77 (9) , 741-746
Finite-Element Implementation of a Self-consistent Texture Model with a Hardening Law Based on Dislocation Densities
- 1 January 2000
- Published by Springer Nature
- p. 49-70
A Comprehensive Model for Solid State Sintering and Its Application to Silicon Carbide
- 1 January 2000
- Published by Springer Nature
- p. 49-70
A Comprehensive Model for Solid State Sintering and Its Application to Silicon Carbide