Gerald E. Jellison
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gerald E. Jellison has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Christopher M. Rouleau
Center for Nanophase Materials Sciences division, Oak Ridge National Laboratory 2 , Oak Ridge, Tennessee 37830
5 shared publications - Lynn A. Boatner
Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831, USA
5 shared publications D. H. Lowndes
Solid State Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831-6030
4 shared publicationsD. J. Singh
Materials Science and Technology Division, Oak Ridge National Laboratory , Oak Ridge, Tennessee 37831-6092, USA
3 shared publications- Oriol Arteaga
Universitat de Barcelona
3 shared publications D. N. Mashburn
Solid State Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831-6056
2 shared publications
Latest Publications
- 30 July 2026
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 632
Quantitative measurement of pebble fuel anisotropy using generalized ellipsometry
- 30 July 2026
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 632
Quantitative measurement of pebble fuel anisotropy using generalized ellipsometry
- 1 June 2026
- Published by American Vacuum Society in Surface Science Spectra
- Vol. 33 (1)
Optical functions of crystalline and amorphous TeO2
The optical functions of crystalline paratellurite (α-TeO2) and amorphous TeO2 were determined using several optical techniques: (1) standard spectroscopic two-modulator generalized ellipsometry (2-MGE) of paratellurite (200–850 nm, 6.2–1.46 eV), (2) near-normal-incidence two-modulator generalized ellipsometry microscopy (2-MGEM) of paratellurite (577 nm, 2.15 eV), (3) Mueller matrix transmission of paratellurite (320–798 nm, 3.87–1.55 eV), and (4) polarized transmission of paratellurite (323.6–334.3 nm, 3.83–3.71 eV). The 2-MGE measurements yielded highly accurate values of the dielectric functions and error estimates from 1.46 to 6.2 eV for both paratellurite and amorphous TeO2, whereas the polarization-dependent transmission yielded more accurate values of the absorption coefficient below the band edge of paratellurite. The 2-MGEM measured the diattenuation of paratellurite, which is related to the birefringence. Mueller matrix transmission measurements of paratellurite of a (001) cut crystal as a function of angle of incidence were used to determine both the birefringence and the rotary power as a function of photon energy.
- 1 June 2026
- Published by American Vacuum Society in Surface Science Spectra
- Vol. 33 (1)
Optical functions of crystalline and amorphous TeO2
The optical functions of crystalline paratellurite (α-TeO2) and amorphous TeO2 were determined using several optical techniques: (1) standard spectroscopic two-modulator generalized ellipsometry (2-MGE) of paratellurite (200–850 nm, 6.2–1.46 eV), (2) near-normal-incidence two-modulator generalized ellipsometry microscopy (2-MGEM) of paratellurite (577 nm, 2.15 eV), (3) Mueller matrix transmission of paratellurite (320–798 nm, 3.87–1.55 eV), and (4) polarized transmission of paratellurite (323.6–334.3 nm, 3.83–3.71 eV). The 2-MGE measurements yielded highly accurate values of the dielectric functions and error estimates from 1.46 to 6.2 eV for both paratellurite and amorphous TeO2, whereas the polarization-dependent transmission yielded more accurate values of the absorption coefficient below the band edge of paratellurite. The 2-MGEM measured the diattenuation of paratellurite, which is related to the birefringence. Mueller matrix transmission measurements of paratellurite of a (001) cut crystal as a function of angle of incidence were used to determine both the birefringence and the rotary power as a function of photon energy.
- 15 July 2024
- Published by American Vacuum Society in Surface Science Spectra
- Vol. 31 (2)
Optical functions of uniaxial rutile and anatase (TiO2) revisited
The optical functions of uniaxial rutile and anatase (TiO2) were determined from 200 to 850 nm (6.2 to 1.46 eV) using several of four optical techniques: (1) standard spectroscopic two-modulator generalized ellipsometry (2-MGE), (2) near-normal-incidence two-modulator generalized ellipsometry microscopy (2-MGEM), (3) Mueller matrix transmission of rutile, and (4) polarized transmission of rutile. The 2-MGE measurements yielded highly accurate values of the dielectric functions and error estimates from 1.46 to 6.2 eV, whereas the polarization-dependent transmission yielded more accurate values of the absorption coefficient below the band edge of rutile. The 2-MGEM also measured the diattenuation, which is related to the birefringence, and other parameters but at near-normal incidence at a single wavelength (577 nm).
- 15 July 2024
- Published by American Vacuum Society in Surface Science Spectra
- Vol. 31 (2)
Optical functions of uniaxial rutile and anatase (TiO2) revisited
The optical functions of uniaxial rutile and anatase (TiO2) were determined from 200 to 850 nm (6.2 to 1.46 eV) using several of four optical techniques: (1) standard spectroscopic two-modulator generalized ellipsometry (2-MGE), (2) near-normal-incidence two-modulator generalized ellipsometry microscopy (2-MGEM), (3) Mueller matrix transmission of rutile, and (4) polarized transmission of rutile. The 2-MGE measurements yielded highly accurate values of the dielectric functions and error estimates from 1.46 to 6.2 eV, whereas the polarization-dependent transmission yielded more accurate values of the absorption coefficient below the band edge of rutile. The 2-MGEM also measured the diattenuation, which is related to the birefringence, and other parameters but at near-normal incidence at a single wavelength (577 nm).
- 3 January 2024
- Published by American Physical Society (APS) in Physical Review B
- Vol. 109 (3) , 035201
Spatial dispersion in silicon
Spatial dispersion (SD) is a nonlocal effect that can introduce optical anisotropy in an otherwise isotropic material, causing the electromagnetic response at a given point to depend not only on the local field, but also on the field in the vicinity of that point. In this study, we investigate the impact of SD on a cubic semiconductorlike silicon, which is typically considered a negligible effect due to the small size of the lattice parameters with respect to the wavelength of light. However, our findings demonstrate that SD can be significant above the band gap, where transmission measurements are not feasible and reflection measurements are required for characterization. We utilize Mueller matrix ellipsometry spectroscopy to quantify the anisotropy caused by SD in (110) and (100) silicon wafers, and determine the complete permittivity tensor of silicon when spatial dispersion is included. In the most general case, this tensor is found to depend on two complex parameters.
- 3 January 2024
- Published by American Physical Society (APS) in Physical Review B
- Vol. 109 (3) , 035201
Spatial dispersion in silicon
Spatial dispersion (SD) is a nonlocal effect that can introduce optical anisotropy in an otherwise isotropic material, causing the electromagnetic response at a given point to depend not only on the local field, but also on the field in the vicinity of that point. In this study, we investigate the impact of SD on a cubic semiconductorlike silicon, which is typically considered a negligible effect due to the small size of the lattice parameters with respect to the wavelength of light. However, our findings demonstrate that SD can be significant above the band gap, where transmission measurements are not feasible and reflection measurements are required for characterization. We utilize Mueller matrix ellipsometry spectroscopy to quantify the anisotropy caused by SD in (110) and (100) silicon wafers, and determine the complete permittivity tensor of silicon when spatial dispersion is included. In the most general case, this tensor is found to depend on two complex parameters.
- Open Access
- 25 August 2023
- Published by American Vacuum Society in Surface Science Spectra
- Vol. 30 (2)
Optical functions of uniaxial zinc oxide (ZnO) revisited
The optical functions of uniaxial ZnO are determined from 200 to 850 nm (6.2–1.46 eV) using three different ellipsometric techniques: (1) standard spectroscopic two-modulator generalized ellipsometry (2-MGE), (2) transmission two-modulator generalized ellipsometry, and (3) near-normal incidence two modulator generalized ellipsometry microscopy (2-MGEM). The 2-MGE results in very accurate values of the dielectric functions and error estimates from 1.46 to 6.2 eV, while the transmission 2-MGE results in more accurate values of the birefringence and associated errors below the band edge where ZnO is transparent. The 2-MGEM also measures the diattenuation (which is related to the birefringence) and other parameters, but at near-normal incidence at a single wavelength (577 nm). The 2-MGEM is designed as a scanning instrument resulting in these parameters being measured over a surface.
- 25 August 2023
- Published by American Vacuum Society in Surface Science Spectra
- Vol. 30 (2)
Open AccessOptical functions of uniaxial zinc oxide (ZnO) revisited
The optical functions of uniaxial ZnO are determined from 200 to 850 nm (6.2–1.46 eV) using three different ellipsometric techniques: (1) standard spectroscopic two-modulator generalized ellipsometry (2-MGE), (2) transmission two-modulator generalized ellipsometry, and (3) near-normal incidence two modulator generalized ellipsometry microscopy (2-MGEM). The 2-MGE results in very accurate values of the dielectric functions and error estimates from 1.46 to 6.2 eV, while the transmission 2-MGE results in more accurate values of the birefringence and associated errors below the band edge where ZnO is transparent. The 2-MGEM also measures the diattenuation (which is related to the birefringence) and other parameters, but at near-normal incidence at a single wavelength (577 nm). The 2-MGEM is designed as a scanning instrument resulting in these parameters being measured over a surface.
- 14 November 2022
- Published by Optica Publishing Group in Journal of the Optical Society of America A
- Vol. 39 (12) , 2225-2237
Ellipsometry: dielectric functions of anisotropic crystals and symmetry
The optical functions of anisotropic materials can be determined using generalized ellipsometry, which can measure the cross-polarization coefficients (CPs) of the sample surface reflections. These CPs have several symmetry relations with respect to the symmetry of the crystal. This paper explores the symmetry relations of these CPs for uniaxial, orthorhombic, and monoclinic crystals and the requirements for generalized ellipsometry. Several ellipsometry measurement configurations are examined, including the requirements for the accurate measurements of the dielectric functions of anisotropic crystals.
- 14 November 2022
- Published by Optica Publishing Group in Journal of the Optical Society of America A
- Vol. 39 (12) , 2225-2237
Ellipsometry: dielectric functions of anisotropic crystals and symmetry
The optical functions of anisotropic materials can be determined using generalized ellipsometry, which can measure the cross-polarization coefficients (CPs) of the sample surface reflections. These CPs have several symmetry relations with respect to the symmetry of the crystal. This paper explores the symmetry relations of these CPs for uniaxial, orthorhombic, and monoclinic crystals and the requirements for generalized ellipsometry. Several ellipsometry measurement configurations are examined, including the requirements for the accurate measurements of the dielectric functions of anisotropic crystals.
- 7 December 2021
- Published by Wiley in Physica Status Solidi (a)
- Vol. 219 (16) , 2100378
Generalized Ellipsometry Measurements of Crystalline Thin Film and Bulk Tin Oxide
Several bulk and thin‐film crystals of SnO2 are grown and examined using generalized ellipsometry techniques. The bulk samples are grown using the chemical vapor transport technique and thin films of SnO2 are grown using the pulsed laser deposition technique. The bulk samples are examined using the two‐modulator generalized ellipsometry microscope (2‐MGEM) at normal incidence and the spectroscopic two‐modulator generalized ellipsometer (2‐MGE). The spectroscopic optical functions of tin oxide are then obtained using the 2‐MGE from 1.46 to 6.2 eV. The material is highly birefringent, and the ordinary bandgap is less than the extraordinary band edge. 2‐MGE measurements are also made on thin‐film samples of crystalline tin oxide grown on sapphire and rutile, showing no cross polarization. Because of the complicated morphology of the tin oxide films grown on sapphire, the ellipsometry data are simulated using the Tauc–Lorentz model. Films grown on rutile had the optic axis perpendicular to the sample surface, but the film is strained, resulting in a more complicated ellipsometric spectrum. These films are modeled using the air/surface roughness/tin oxide/interface/rutile model, where the roughness and interface are modeled using the incomplete Beta function.
- 7 December 2021
- Published by Wiley in Physica Status Solidi (a)
- Vol. 219 (16) , 2100378
Generalized Ellipsometry Measurements of Crystalline Thin Film and Bulk Tin Oxide
Several bulk and thin‐film crystals of SnO2 are grown and examined using generalized ellipsometry techniques. The bulk samples are grown using the chemical vapor transport technique and thin films of SnO2 are grown using the pulsed laser deposition technique. The bulk samples are examined using the two‐modulator generalized ellipsometry microscope (2‐MGEM) at normal incidence and the spectroscopic two‐modulator generalized ellipsometer (2‐MGE). The spectroscopic optical functions of tin oxide are then obtained using the 2‐MGE from 1.46 to 6.2 eV. The material is highly birefringent, and the ordinary bandgap is less than the extraordinary band edge. 2‐MGE measurements are also made on thin‐film samples of crystalline tin oxide grown on sapphire and rutile, showing no cross polarization. Because of the complicated morphology of the tin oxide films grown on sapphire, the ellipsometry data are simulated using the Tauc–Lorentz model. Films grown on rutile had the optic axis perpendicular to the sample surface, but the film is strained, resulting in a more complicated ellipsometric spectrum. These films are modeled using the air/surface roughness/tin oxide/interface/rutile model, where the roughness and interface are modeled using the incomplete Beta function.
- 22 December 2015
- Published by Elsevier in Thin Solid Films
- Vol. 617, 38-43
Optical properties of a nanostructured glass-based film using spectroscopic ellipsometry
- 22 December 2015
- Published by Elsevier in Thin Solid Films
- Vol. 617, 38-43
Optical properties of a nanostructured glass-based film using spectroscopic ellipsometry
- 15 February 2012
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 111 (4) , 043521
Refractive index of sodium iodide
The refractive index of sodium iodide, an important scintillator material that is widely used for radiation detection, is based on a single measurement made by Spangenberg at one wavelength using the index-matching liquid immersion method (Z. Kristallogr. 57, 494 (1923)). In the present paper, we present new results for the refractive index of sodium iodide as measured by the minimum deviation technique at six wavelengths between 436 nm (n = 1.839 ± 0.002) and 633 nm (n = 1.786 ± 0.002). These six measurements can be fit to a Sellmeier model, resulting in a χ2 of 1.02, indicating a good fit to the data. In addition, we report on ellipsometry measurements, which suggest that the near-surface region of the air sensitive NaI crystal seriously degrades, even in a moisture-free environment, resulting in a significantly lower value of the refractive index near the surface. First-principles theoretical calculations of the NaI refractive index that agree with the measured values within 0.025-0.045 are also presented and discussed.
- 15 February 2012
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 111 (4) , 043521
Refractive index of sodium iodide
The refractive index of sodium iodide, an important scintillator material that is widely used for radiation detection, is based on a single measurement made by Spangenberg at one wavelength using the index-matching liquid immersion method (Z. Kristallogr. 57, 494 (1923)). In the present paper, we present new results for the refractive index of sodium iodide as measured by the minimum deviation technique at six wavelengths between 436 nm (n = 1.839 ± 0.002) and 633 nm (n = 1.786 ± 0.002). These six measurements can be fit to a Sellmeier model, resulting in a χ2 of 1.02, indicating a good fit to the data. In addition, we report on ellipsometry measurements, which suggest that the near-surface region of the air sensitive NaI crystal seriously degrades, even in a moisture-free environment, resulting in a significantly lower value of the refractive index near the surface. First-principles theoretical calculations of the NaI refractive index that agree with the measured values within 0.025-0.045 are also presented and discussed.