SRSandra Cristina dos Santos Rocha

Sandra Cristina dos Santos Rocha

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sandra Cristina dos Santos Rocha has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Slot-Rectangular Spouted Bed: Hydrodynamic Stability and Effects of Operating Conditions on Drying Performance

    by Matheus B. Braga, Ziliang Wang, John R. Grace, C. Jim Lim, Sandra C. S. Rocha

    A new spouted-bed configuration (rectangular cross-section with air entry through two bottom slots) was investigated as a dryer of milk and a paste mixture of milk and blackberry pulp. The aim was to analyze hydrodynamic stability and the effects of operating conditions on powder production efficiency. For the best conditions of paste-feeding flow rate, air temperature and inert type, hydrodynamic was stable and powder production efficiency was greater than 75%. The slot-rectangular spouted bed allowed for tripling of the paste-feeding flow rate at a lower air velocity compared to the conventional geometry, showing its potential for process scale-up.


  • Drying of milk–blackberry pulp mixture in spouted bed

    by Matheus B. Braga, Sandra C. S. Rocha


  • Agglomeration of Sodium Bicarbonate in Vibrofluidized Bed: Process Analysis and Evaluation of CO2Release

    by S. C. S. Rocha, J. F. Nunes

    Agglomeration of sodium bicarbonate in a vibrofluidized bed using an aqueous polymeric suspension as binding agent was studied to determine the effects of vibration parameters (amplitude and frequency) and drying air temperature on process performance and product quality. Product quality was evaluated by determination and comparison of CO2 release from agglomerated and raw sodium bicarbonate. An experimental design was developed for the process analysis. Amplitude and frequency of vibration and air temperature were analyzed as independent variables and the response for process evaluation was the particle growth, which is related to the particle protection. Analyses of CO2 release were made for the agglomerates stored under different environments of controlled relative humidity and temperatures, week by week, during 4 weeks. Also, vapor adsorption isotherms at 25°C were obtained, which showed changes in the sodium bicarbonate hygroscopic characteristics after agglomeration.


  • Drying of Tropical Fruit Pulps: Spouted Bed Process Optimization as a Function of Pulp Composition

    by S. C. S. Rocha, J. S. Souza, O. L. S. Alsina, M. F. D. Medeiros

    Results of drying of tropical fruit pulps in spouted beds (SBs) are presented, focusing on the effects of fruit pulp composition on the SB fluid dynamics and process performance and the development of new products formulated from mixtures of pulps with varied composition. It was verified that high starch and lipid contents favored stable fluid dynamics and high powder production efficiency, while high reducing sugar concentrations resulted in bad dynamic regime and very low powder production. Powder production efficiency was statistically correlated with the pulp composition. Also, drying of mixtures of fruit pulps with addition of starch and lipids was investigated. Results of fluid dynamics, drying performance, and sensory tests of yogurts enriched with the powders revealed promising potential of the SB for obtaining high-quality fruit powders.


  • Open Access

    Caracterização física e germinação de sementes de Senna macranthera

    by Marina Pozitano, Sandra Cristina dos Santos Rocha

    Poor knowledge of the physical traits of forest species seeds causes difficulties in developing methodologies for their assessment and preservation. Senna macranthera (Collad.) Irwin et Barn. is a leguminous pioneer plant that belongs to the Caesalpinioideae. It is popularly known as fedegoso and its seeds have tegumentary dormancy. In this study, physical characterization of fedegoso seeds was obtained by evaluating the Sauter mean diameter, sphericity, densities (real, apparent and bulk), porosity, dynamic angle of repose and weight of 1000 seeds: 3.3 mm; 0.52; 1397.2 kg.m-³; 1371.9 kg.m-³; 884.4 kg.m-³; 1.81%; 10º and 41.05 g, respectively. S. macranthera seeds were packed in plastic bags and stored in a conventional refrigerator at 5 ºC for 280 days and analyzed periodically for germination and moisture content. The seeds were chemically scarified by immersion in concentrated sulphuric acid for 20 minutes to break dormancy. The germination tests showed that seeds remained viable during storage.O desconhecimento sobre as características físicas de sementes de espécies florestais dificulta o desenvolvimento de metodologias para a sua avaliação e preservação. A Senna macranthera (Collad.) Irwin et Barn. é uma planta pioneira que pertence à família Leguminosae - Caesalpinioideae, conhecida popularmente como fedegoso e suas sementes possuem dormência tegumentar. Neste estudo foi realizada a caracterização física das sementes desta espécie em relação ao diâmetro médio de Sauter, esfericidade, densidade (real, aparente e bulk), porosidade da partícula, ângulo de repouso dinâmico e o peso de 1000 sementes (3,3 mm; 0,52; 1397,2 kg.m-³; 1371,9 kg.m-³; 884,4 kg.m-³; 1,81%; 10º e 41,05 g, respectivamente). Além disso, as sementes de S. macranthera foram acondicionadas em sacos de plástico e armazenadas em geladeira convencional a 5 ºC durante 280 dias e, periodicamente, foram realizadas análises de germinação e umidade. Para a quebra da dormência, as sementes foram escarificadas quimicamente por imersão em ácido sulfúrico concentrado durante 20 minutos. O teste de germinação indicou que as sementes se mantiveram viáveis durante o período analisado


  • Liquid‐particle surface properties on spouted bed coating and drying performance

    by S. C. S. Rocha, M. W. Donida, A. M. M. Marques

    Polymeric coating has been applied to particles for several reasons, which goes from enhancing product esthetics to control the release of chemicals. Spouted beds are among the equipments widely used to coat particles. Its choice is justified by the cyclic movement of the particles in stable spouting resulting in product homogeneity and good solid–fluid contact with high heat and mass transfer rates. Also, the spouted bed with inert particles is an alternative to drying pastes due to its low cost and applicability to low scale production. This work presents results of coating and drying efficiencies for different systems that combine 04 different solids and 03 formulations of suspensions. Materials having different surface tension were chosen and suspensions with varying surface tensions were formulated, resulting in different wettabilities (quantified by contact angles measurements). The results show the direct influence of these properties on the coating and drying performances.


  • Open Access

    Mathematical modeling of handmade recycled paper drying kinetics and sorption isotherms

    by M. G. A. Vieira, S. C. S. Rocha

    The objective of this work is to analyze and compare the natural and forced convective drying of handmade recycled paper. Drying of recycled cellulose pulp was carried out under laboratory environment conditions and in a convective dryer with forced air circulation and controlled conditions of air temperature and velocity. The tests were conducted following a two-factor central composed factorial design of experiments, with six runs at the central point. The drying results were analyzed and fitted to mathematical models of Fick, Henderson and Pabis (Fick s modified equation), Page and He (considering the nonlinear Fick effect). The model of Page represented best the experimental data and the one of Henderson and Pabis resulted in an adequate fit for the paper drying kinetics. Sorption isotherms were determined for the dried paper and the models of GAB (Guggenheim-Anderson-de Boer) and GDW (Generalised D Arcy and Watt) resulted in excellent fits of the experimental data. The water sorption mechanism was suggested by the analysis of the calculated parameters of the GDW model


  • Open Access

    Intermittent drying of beans in a spouted bed

    by C. A. Oliveira, S. C. S. Rocha

    Carioca beans are a highly nutritious grain, in terms of the amount of protein, iron and potassium as well as carbohydrates and fiber and as a source of vitamins. The moisture content of recently picked beans is too high for good preservation and storage, resulting in the need for drying before packaging. In this work, the drying of Carioca beans in a laboratory scale spouted bed under intermittent conditions of the drying air was experimentally analyzed. Experiments carried out consisted of two types of intermittent regime: intermittence in the spout regime, referred to as spouted/fixed bed and intermittence of the air supply to the bed, called spouted bed/rest. The results were compared to those for bean drying in a spouted bed dryer without intermittence


  • Energy Efficiency and Drying Kinetics of Recycled Paper Pulp

    by M. G. A. Vieira, L. Estrella, S. C. S. Rocha

    In this work, the influences of the air temperature and velocity on the drying kinetics of recycled paper pulp were analyzed. The increase of both variables positively influences the process, concerning the final moisture content and the drying time. However, optical microscopy and visual observation showed worse quality of the paper for drying conditions of high air temperature and velocity, presenting less uniformity and overdried surfaces. The dryer energy efficiency was evaluated by performance parameters and the results were compared with the ones obtained for other types of industrial paper dryers, presenting good agreement.


  • Coating and Drying in Spouted Bed: Influence of the Liquid-Particle Work of Adhesion

    by M. W. Donida, S. C. S. Rocha, B. D. Castro, A. M. M. Marques

    The aim of this work is to analyze the resulting process: coating or drying, and the respective fluid dynamic behavior, by bottom-spraying polymeric suspensions on a spouted bed of inert particles. Glass beads, ABS®, polypropylene (PP), and polystyrene (PS) were chosen as inert particles and were analyzed and characterized by their physicochemical properties. The polymeric suspensions were characterized by density, surface tension, rheology, and wettability. The fluid dynamic behavior of the bed was correlated with the particles and suspensions characteristics for each process: coating and drying. Each process performance was correlated with the polymeric suspension-particle work of adhesion.