M. J. Yang
Research Subjects
M. J. Yang has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- B. R. Bennett
U.S. Naval Research Laboratory, Washington, DC, USA
8 shared publications B. V. Shanabrook
Electronics Science and Technology Division, Naval Research Laboratory, Washington, DC 20375-5347
6 shared publicationsW. J. Moore
Electronics Science and Technology Division, Naval Research Laboratory, Washington, DC 20375-5347
5 shared publicationsC. H. Yang
Naval Research Laboratory, Washington D.C. 20375
4 shared publicationsR. J. Wagner
Naval Research Laboratory, Washington, D.C. 20375
3 shared publicationsC. L. Felix
2 shared publications
Latest Publications
- 4 February 2008
- Published by Defense Technical Information Center (DTIC)
Unmanned Aircraft Systems' Role In Network Centric Warfare
Using RHEED and STM, we have studied surface reconstructions and formation of islands and interfaces for the 6.1 Angstrom family of compound semiconductors (InAs, GaSb, AlSb). The structure and stoichiometry of MBE-grown antimonide surfaces lead to growth and roughening mechanisms that are distinctly different from other III-V materials. When a new material is grown on an antimonide surface, some blurring of the resulting heterointerface must occur in the form of monolayer islands or atomic-scale intermixing.
- 4 February 2008
- Published by Defense Technical Information Center (DTIC)
Unmanned Aircraft Systems' Role In Network Centric Warfare
Using RHEED and STM, we have studied surface reconstructions and formation of islands and interfaces for the 6.1 Angstrom family of compound semiconductors (InAs, GaSb, AlSb). The structure and stoichiometry of MBE-grown antimonide surfaces lead to growth and roughening mechanisms that are distinctly different from other III-V materials. When a new material is grown on an antimonide surface, some blurring of the resulting heterointerface must occur in the form of monolayer islands or atomic-scale intermixing.
- 20 January 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 323-326
Low-voltage, high-speed AlSb-InAsSb HEMTs
We report on the fabrication and characteristics of antimonide-based HEMTs with an InAsSb channel. Infrared photoluminescence measurements at 5 K confirm that the addition of Sb changes the band structure from a staggered type-II heterojunction lineup to a type-I. These HEMTs with a 0.1 /spl mu/m gate length exhibit decreased output conductance and improved voltage gain compared to previous AlSb/InAs HEMTs with similar gate length. At V/sub DS/=0.6 V, a microwave transconductance of 700 mS/mm and an output conductance of 110 mS/mm were obtained corresponding to a voltage gain of 6. AlSb/InAs HEMTs have also been fabricated with a 60 nm gate length. These HEMTs exhibit-a low-field source-drain resistance of 0.35 /spl Omega/-mm and a measured f/sub T/ of 90 GHz at a drain voltage of only 100 mV. This f/sub T/ value is the highest reported for any FET at this drain voltage.
- 20 January 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 323-326
Low-voltage, high-speed AlSb-InAsSb HEMTs
We report on the fabrication and characteristics of antimonide-based HEMTs with an InAsSb channel. Infrared photoluminescence measurements at 5 K confirm that the addition of Sb changes the band structure from a staggered type-II heterojunction lineup to a type-I. These HEMTs with a 0.1 /spl mu/m gate length exhibit decreased output conductance and improved voltage gain compared to previous AlSb/InAs HEMTs with similar gate length. At V/sub DS/=0.6 V, a microwave transconductance of 700 mS/mm and an output conductance of 110 mS/mm were obtained corresponding to a voltage gain of 6. AlSb/InAs HEMTs have also been fabricated with a 60 nm gate length. These HEMTs exhibit-a low-field source-drain resistance of 0.35 /spl Omega/-mm and a measured f/sub T/ of 90 GHz at a drain voltage of only 100 mV. This f/sub T/ value is the highest reported for any FET at this drain voltage.
- 1 January 2003
- Published by Springer Nature in MRS Proceedings
- Vol. 799
Pump Wavelength Tuning of Optical Pumping Injection Cavity Lasers for Enhancing Mid-Infrared Operation
- 1 January 2003
- Published by Springer Nature in MRS Proceedings
- Vol. 799
Pump Wavelength Tuning of Optical Pumping Injection Cavity Lasers for Enhancing Mid-Infrared Operation
- 31 July 2001
- Published by Elsevier in Optical Materials
- Vol. 17 (1-2) , 179-183
Type-II antimonide quantum wells for mid-infrared lasers
- 31 July 2001
- Published by Elsevier in Optical Materials
- Vol. 17 (1-2) , 179-183
Type-II antimonide quantum wells for mid-infrared lasers
- 1 June 2000
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 87 (11) , 7876-7879
Transport properties of Be- and Si-doped AlSb
- 1 June 2000
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 87 (11) , 7876-7879
Transport properties of Be- and Si-doped AlSb
- 1 December 1999
- Published by Optica Publishing Group in Optics and Photonics News
- Vol. 10 (12) , 18
High-Temperature Diode and Optically-Pumped Mid-IR Lasers with Type-II “W” Quantum Wells
- 1 December 1999
- Published by Optica Publishing Group in Optics and Photonics News
- Vol. 10 (12) , 18
High-Temperature Diode and Optically-Pumped Mid-IR Lasers with Type-II “W” Quantum Wells
- 15 November 1999
- Published by American Physical Society (APS) in Physical Review B
- Vol. 60 (20) , R13958-R13961
Magnetocapacitance and far-infrared photoconductivity in GaSb/InAs composite quantum wells
Magnetocapacitance-voltage measurements are performed in hybridized composite quantum wells at 4.2 K. In the quantum Hall regime, the capacitance reveals a series of oscillations resulting from the spin-resolved Landau levels. It is found that the capacitance signal is determined by the filling factor that is the difference between the electron and hole filling factors. A fan chart is generated in order to determine the Fermi level position relative to the electron and hole subbands at different gate voltages. When the Fermi level resides in the middle of the hybridization gap, far infrared photo signals have been detected with photon energy ranging from 1.4 to 5.3 meV. The hybridization gap is determined to be 3 meV.
- 15 November 1999
- Published by American Physical Society (APS) in Physical Review B
- Vol. 60 (20) , R13958-R13961
Magnetocapacitance and far-infrared photoconductivity in GaSb/InAs composite quantum wells
Magnetocapacitance-voltage measurements are performed in hybridized composite quantum wells at 4.2 K. In the quantum Hall regime, the capacitance reveals a series of oscillations resulting from the spin-resolved Landau levels. It is found that the capacitance signal is determined by the filling factor that is the difference between the electron and hole filling factors. A fan chart is generated in order to determine the Fermi level position relative to the electron and hole subbands at different gate voltages. When the Fermi level resides in the middle of the hybridization gap, far infrared photo signals have been detected with photon energy ranging from 1.4 to 5.3 meV. The hybridization gap is determined to be 3 meV.
- 29 July 1999
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 86 (4) , 1796-1799
Optimum growth parameters for type-II infrared lasers
The surface, structural, and optical properties of InAs/InGaSb/AlSb mid-infrared lasers grown by molecular beam epitaxy have been systematically studied, respectively, by Nomarski differential interference contrast, high-resolution x-ray diffraction, and variable-temperature photoluminescence. It is found that the optimum growth temperature is between 400 and 450 °C, based on the calibrated transmission thermometry. In addition, the impact of interfacial bond type and Sb sources has been investigated. A 5.91 μm laser, grown with the optimal growth parameters, exhibits a maximum cw operating temperature of 210 K.
- 29 July 1999
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 86 (4) , 1796-1799
Optimum growth parameters for type-II infrared lasers
The surface, structural, and optical properties of InAs/InGaSb/AlSb mid-infrared lasers grown by molecular beam epitaxy have been systematically studied, respectively, by Nomarski differential interference contrast, high-resolution x-ray diffraction, and variable-temperature photoluminescence. It is found that the optimum growth temperature is between 400 and 450 °C, based on the calibrated transmission thermometry. In addition, the impact of interfacial bond type and Sb sources has been investigated. A 5.91 μm laser, grown with the optimal growth parameters, exhibits a maximum cw operating temperature of 210 K.
- 1 July 1998
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 34 (4) , 1054-1059
Hybrid ferromagnet-semiconductor nonvolatile gate
- 1 July 1998
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 34 (4) , 1054-1059
Hybrid ferromagnet-semiconductor nonvolatile gate
- 9 March 1998
- Published by AIP Publishing in Applied Physics Letters
- Vol. 72 (10) , 1193-1195
Modulation doping of InAs/AlSb quantum wells using remote InAs donor layers
Sheet carrier concentrations in quantum wells of InAs clad by AlSb were enhanced by modulation doping with very thin (9–12 Å) remote InAs(Si) donor layers. The growth temperature of the donor layers was a key parameter, with relatively low temperatures required to minimize Si segregation into the AlSb. Sheet carrier concentrations as high as and were achieved by single- and double-sided modulation doping, respectively. High electron mobility transistors fabricated using the modulation doped structure exhibited a unity current gain cut-off frequency of 60 GHz for a 0.5 μm gate length at a source-drain voltage of 0.5 V.- 9 March 1998
- Published by AIP Publishing in Applied Physics Letters
- Vol. 72 (10) , 1193-1195
Modulation doping of InAs/AlSb quantum wells using remote InAs donor layers
Sheet carrier concentrations in quantum wells of InAs clad by AlSb were enhanced by modulation doping with very thin (9–12 Å) remote InAs(Si) donor layers. The growth temperature of the donor layers was a key parameter, with relatively low temperatures required to minimize Si segregation into the AlSb. Sheet carrier concentrations as high as and were achieved by single- and double-sided modulation doping, respectively. High electron mobility transistors fabricated using the modulation doped structure exhibited a unity current gain cut-off frequency of 60 GHz for a 0.5 μm gate length at a source-drain voltage of 0.5 V.