Jawad Al Khaburi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jawad Al Khaburi has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Elizabeth Andrea Nelson
Glasgow Caledonian University, Glasgow, UK
2 shared publications A A Dehghani-Sanij
Mechanical Engineering, University of Leeds, Leeds, UK
1 shared publicationAbbas A. Dehghani-Sanij
1 shared publicationJ Hutchinson
ConvaTec Limited, Deeside, UK
1 shared publicationJerry Hutchinson
1 shared publication
Latest Publications
- 20 August 2011
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 34 (3) , 378-385
Effect of bandage thickness on interface pressure applied by compression bandages
Medical compression bandages are widely used in the treatment of chronic venous disorder. In order to design effective compression bandages, researchers have attempted to describe the interface pressure applied by these bandages using mathematical models. This paper reports on the work carried out to derive the mathematical model used to describe the interface pressure applied by single-layer bandage using two different approaches. The first assumes that the bandage thickness is negligible, whereas the second model includes the bandage thickness. The estimated pressures using the two formulae are then compared, simulated over a 3D representation of a real leg and validated experimentally. Both theoretical and experimental results have shown that taking bandage thickness into consideration while estimating the pressures applied by a medical compression bandage will result in more accurate estimation. However, the additional accuracy is clinically insignificant.
- 20 August 2011
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 34 (3) , 378-385
Effect of bandage thickness on interface pressure applied by compression bandages
Medical compression bandages are widely used in the treatment of chronic venous disorder. In order to design effective compression bandages, researchers have attempted to describe the interface pressure applied by these bandages using mathematical models. This paper reports on the work carried out to derive the mathematical model used to describe the interface pressure applied by single-layer bandage using two different approaches. The first assumes that the bandage thickness is negligible, whereas the second model includes the bandage thickness. The estimated pressures using the two formulae are then compared, simulated over a 3D representation of a real leg and validated experimentally. Both theoretical and experimental results have shown that taking bandage thickness into consideration while estimating the pressures applied by a medical compression bandage will result in more accurate estimation. However, the additional accuracy is clinically insignificant.
- 2 March 2011
- Published by SAGE Publications in Phlebology: The Journal of Venous Disease
- Vol. 26 (2) , 75-83
Impact of multilayered compression bandages on sub-bandage interface pressure: a model
Background: Multi-component medical compression bandages are widely used to treat venous leg ulcers. The sub-bandage interface pressures induced by individual components of the multi-component compression bandage systems are not always simply additive. Current models to explain compression bandage performance do not take account of the increase in leg circumference when each bandage is applied, and this may account for the difference between predicted and actual pressures. Objective: To calculate the interface pressure when a multi-component compression bandage system is applied to a leg. Method: Use thick wall cylinder theory to estimate the sub-bandage pressure over the leg when a multi-component compression bandage is applied to a leg. Results: A mathematical model was developed based on thick cylinder theory to include bandage thickness in the calculation of the interface pressure in multi-component compression systems. In multi-component compression systems, the interface pressure corresponds to the sum of the pressures applied by individual bandage layers. However, the change in the limb diameter caused by additional bandage layers should be considered in the calculation. Adding the interface pressure produced by single components without considering the bandage thickness will result in an overestimate of the overall interface pressure produced by the multi-component compression systems. At the ankle (circumference 25 cm) this error can be 19.2% or even more in the case of four components bandaging systems. Conclusion: Bandage thickness should be considered when calculating the pressure applied using multi-component compression systems.
- 2 March 2011
- Published by SAGE Publications in Phlebology: The Journal of Venous Disease
- Vol. 26 (2) , 75-83
Impact of multilayered compression bandages on sub-bandage interface pressure: a model
Background: Multi-component medical compression bandages are widely used to treat venous leg ulcers. The sub-bandage interface pressures induced by individual components of the multi-component compression bandage systems are not always simply additive. Current models to explain compression bandage performance do not take account of the increase in leg circumference when each bandage is applied, and this may account for the difference between predicted and actual pressures. Objective: To calculate the interface pressure when a multi-component compression bandage system is applied to a leg. Method: Use thick wall cylinder theory to estimate the sub-bandage pressure over the leg when a multi-component compression bandage is applied to a leg. Results: A mathematical model was developed based on thick cylinder theory to include bandage thickness in the calculation of the interface pressure in multi-component compression systems. In multi-component compression systems, the interface pressure corresponds to the sum of the pressures applied by individual bandage layers. However, the change in the limb diameter caused by additional bandage layers should be considered in the calculation. Adding the interface pressure produced by single components without considering the bandage thickness will result in an overestimate of the overall interface pressure produced by the multi-component compression systems. At the ankle (circumference 25 cm) this error can be 19.2% or even more in the case of four components bandaging systems. Conclusion: Bandage thickness should be considered when calculating the pressure applied using multi-component compression systems.