NGNader Ghafoori

Nader Ghafoori

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Nader Ghafoori has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Corrosion Performance of Multiple As-Delivered Steel Reinforcing Bar Types Using the ASTM A955 Rapid Macrocell Test

    by Nader Ghafoori, Brandon T. Huynh

    Chloride-induced corrosion of steel reinforcement is a major durability concern for reinforced concrete infrastructure exposed to deicing salts and other chloride-bearing environments. The use of corrosion-resistant reinforcing bars provides a potential means of extending structural service life; however, comparative information on the performance of different reinforcement systems under identical exposure conditions remains important for material selection. In this study, bare, quenched and tempered, Duplex 2304 stainless steel, epoxy-coated, galvanized, and ChromX-9100 reinforcing bars were evaluated in the as-received condition using the Rapid Macrocell test described in ASTM A955. Corrosion rate, cumulative corrosion loss, and anode corrosion potential were monitored during the 15-week testing period. The Duplex 2304 stainless steel reinforcing bars exhibited the highest resistance to chloride-induced corrosion, with an overall average corrosion loss of approximately 0.25% of that of the bare reinforcing bars. The epoxy-coated, galvanized, and ChromX-9100 reinforcing bars exhibited overall average corrosion losses of approximately 25%, 33%, and 40% of that of the bare bars, respectively. In contrast, the quenched and tempered reinforcing bars exhibited an overall average corrosion loss approximately 25% greater than that of the bare reinforcement. These findings provide a direct comparative assessment of commonly available reinforcement systems and can assist in evaluating reinforcement options for concrete structures exposed to aggressive chloride environments.

  • Open Access

    Role of Sodium- and Potassium-Based Activators on the Engineering Properties of Low-Alkali-Activated Binders

    by Aderemi Tobi Gbadamosi, Nader Ghafoori

    Despite extensive research on alkali-activated materials, the comparative performance of sodium- and potassium-based hydroxide–silicate activator systems under low-alkali conditions remains insufficiently understood, particularly across different precursor compositions and engineering properties. This study comparatively evaluated practically workable sodium- and potassium-based activator systems in alkali-activated binders incorporating ground granulated blast-furnace slag, Class F fly ash, and silica fume. Eleven binary and ternary paste formulations were investigated at hydroxide molarities of 0.5–3 M and silicate-to-hydroxide ratios of 0.25–0.67 using NaOH–Na2SiO3 and KOH–K2SiO3 activator systems. Flowability, setting time, temperature evolution, 28- and 90-day compressive strength, 32-week drying shrinkage, water absorption, permeable void content, rapid chloride permeability test (RCPT), and Fourier transform infrared (FTIR) spectroscopy were evaluated. Increasing hydroxide molarity and silicate dosage generally accelerated reaction development and enhanced strength while reducing flowability. Potassium-activated binders exhibited 3–23% higher measured flow, shorter setting times, earlier temperature evolution, and 11–46% lower drying shrinkage. Conversely, sodium-activated binders generally achieved higher 28- and 90-day compressive strengths, together with 4–16% lower water absorption and permeable void contents and lower electrical charge passed during RCPT. FTIR spectroscopy revealed differences in the Si–O–T band positions between the activator systems, indicating differences in aluminosilicate network development. Overall, the findings establish important performance trade-offs between low-alkali sodium- and potassium-based formulations and provide a comparative basis for activator selection in the development of high-performance alkali-activated cementitious materials.

  • Open Access

    Wear resistance of fast-track Type III Portland cement concrete

    by Nader Ghafoori, Mathew Tays, Aderemi Gbadamosi

    This study investigated the wear resistance of selected fast-track Type III Portland cement concrete (FTC) under early opening times (6, 8 hours) and at full maturity (28 days). The effects of varying Type III Portland cement content (386, 445, and 505 kg/m³), with and without an accelerating admixture, were analysed to assess wear depth and deterioration rate. These factors were examined across different opening-time categories and maturity duration. The coefficients of variation and abrasion index from the abrasion tests were also evaluated. Additionally, the correlation between abrasion resistance (wear depth) and bulk strength was explored at both early and maturity durations. Results indicated that the studied FTCs showed improved wear resistance and compressive strength with higher cement content, longer curing periods, and the addition of an accelerating admixture. Test results also revealed that cement content, curing time, and accelerating admixture influenced depth of wear more than compressive strength.


  • Open Access

    Influence of supplementary cementitious materials on sulfate resistance of ultra-high-performance concrete

    by Nader Ghafoori, Aderemi Gbadamosi

    The study presented herein investigated the effect of supplementary cementitious materials (SCMs) on the sulfate resistance of ultra-high-performance concretes (UHPCs) made with ASTM Type III and Type V cement. Three types of UHPCs were prepared for each cement type, namely, one with 100 % cement (C100) and two others with 20 % cement replaced by fly ash (FA20) and a combination of silica fume and fly ash (FA15SF5). These UHPCs were exposed to a 5 % sodium sulfate solution for 365 days to evaluate their sulfate resistance. In addition to the sulfate-induced expansion, the compressive strengths of the studied UHPCs were evaluated under two curing conditions: continuous water curing and curing under exposure to the 5 % sulfate solution. The Rapid Sulfate Permeability Test (RSPT) was also conducted at 28 and 90 days to assess rapid sulfate ions penetration into the studied UHPCs. The results revealed that the addition of supplementary cementitious materials (SCMs) significantly enhanced sulfate resistance in both Type III and Type V cement UHPCs. However, Type V cement UHPCs consistently showed reduced sulfate-induced expansion by approximately 20.4 % compared to Type III cement UHPC, primarily due to its lower C3A content. The Rapid Sulfate Permeability Test (RSPT) results revealed that, at both 28 and 90 days, Type V UHPCs consistently displayed lower penetrability compared to Type III UHPCs. Furthermore, Type V cement UHPCs incorporating SCMs exhibited an average surface penetration reduction of about 6 % relative to their Type III cement counterparts.

  • Open Access

    Role of Cement Type on Properties of High Early-Strength Concrete

    by Nader Ghafoori, Matthew O. Maler, Meysam Najimi, Ariful Hasnat, Aderemi Gbadamosi

    Properties of high early-strength concretes (HESCs) containing Type V, Type III, and rapid hardening calcium sulfoaluminate (CSA) cements were investigated at curing ages of opening time, 24 h, and 28 days. Investigated properties included the fresh (workability, setting time, air content, unit weight, and released heat of hydration), mechanical (compressive and flexural strengths), transport (absorption, volume of permeable voids, water penetration, rapid chloride permeability, and accelerated corrosion resistance), dimensional stability (drying shrinkage), and durability (de-icing salt and abrasion resistance) properties. Test results revealed that the HESC containing Rapid-Set cement achieved the shortest opening time to attain the required minimum strength, followed by Type III and Type V cement HESCs. For the most part, Type V cement HESC produced the best transport and de-icing salt resistance, whereas Rapid-Set cement HESC displayed the best dimensional stability and wear resistance.


  • EFFECT OF CURING TIME AND TYPE ON STRENGTH OF NON-PROPRIETARY BLENDED ULTRA-HIGH-PERFORMANCE CONCRETE

    by Nader Ghafoori, Aderemi Gbadamosi, Ariful Hasnat

    This paper examines the effect of curing age and type on compressive strength of blended non-proprietary ultra-high-performance concrete (UHPC). Eleven plain UHPCs were batched using a constant water to-cementitious materials ratio of 0.21 and an aggregate-to-cementitious materials ratio of 1.20. Four binary, four ternary, and two quaternary blend cementitious materials combinations using Class F fly ash, slag, natural pozzolan, and silica fume, as a partial replacement of Portland cement, were compared with the UHPC made using 100% Portland cement. The findings revealed that, when the UHPCs were moist cured, the ternary blend containing 15% fly ash and 5% silica fume, as a partial substitute of Portland cement, displayed the highest compressive strength at all testing ages. Under moist curing conditions, quaternary blended UHPC containing 20% fly ash, 20% natural pozzolan, and 10% silica fume showed the highest increase in strength once curing age was extended from 90 to 365 days. Most of the UHPCs specimen cured for 7 days in 90°C environment showed superior to similar strength to that of the companion 28-day moist-cured UHPCs.

  • Role of Fly Ash Types on Properties of Cement Based Mixtures

    by Nader Ghafoori, Aderemi Gbadamosi, Ariful Hasnat

    This study investigates the properties of paste, mortar, and concrete made with three distinct fly ash types (traditional, harvested, and blended) replacing 20% of Portland cement, aiming to bridge the gap between supply and consumption of traditional fly ash. The investigated properties included rapid chloride penetration. compressive strength, drying shrinkage, absorption, permeable voids, surface resistivity, resistance to sulfate attack and wear. The cementitious mixtures containing fly ash consistently exhibited superior performance, compared to the reference mixture across all properties examined in this study. Amongst the three fly ash types, the mixtures containing traditional fly ash produced best short, medium and long-term properties. The mixtures containing harvested and blended fly ash exhibited comparable performance between each other, and in certain instances, one outperformed the other.

  • Open Access

    Influence of Admixture Source on Fresh Properties of Self-Consolidating Concrete

    by Nader Ghafoori, Aderemi Gbadamosi, Hamidou Diawara, Ariful Hasnat

    The study presented herein was intended to (1) compare the optimum (minimum) dosage requirements of four different sources of polycarboxylate-based high-range water-reducing admixtures (HRWRAs) and viscosity-modifying admixtures (VMAs) in attaining slump flows of 508 mm, 635 mm, and 711 mm, and a visual stability index (VSI) of 0 (highly stable concrete) or 1 (stable concrete), and (2) assess the flowability/viscosity, stability, passing ability, and filling ability of the resulting self-consolidating concretes. The test results showed that the optimum dosage requirements to obtain a uniform slump flow and visual stability index varied among the four selected admixture sources. The required dosage amount for HRWRAs was highest for the polycarboxylate-ester (PCE) type and lowest for the polycarboxylate-acid (PCA) type. Acceptable flowability plastic viscosity dynamic and static stability, passing ability, and filling ability of self-consolidating concrete can be achieved with the proper dosing of the four studied admixture sources.