Louis-Francois Tanguay
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Louis-Francois Tanguay has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
Mohamad Sawan
Ecole Polytechnique de Montréal
3 shared publicationsM. Sawan
Ecole Polytech, Dept Elect Engn, Montreal, PQ H3C 3A7, Canada
1 shared publicationY. Savaria
Ecole Polytech, Dept Elect Engn, Montreal, PQ H3C 3A7, Canada
1 shared publication
Latest Publications
- 1 June 2009
- Published by Elsevier in Microelectronics Journal
- Vol. 40 (6) , 1026-1031
A very-high output impedance charge pump for low-voltage low-power PLLs
- 1 June 2009
- Published by Elsevier in Microelectronics Journal
- Vol. 40 (6) , 1026-1031
A very-high output impedance charge pump for low-voltage low-power PLLs
- 27 February 2008
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 58 (3) , 205-214
An ultra-low power ISM-band integer-N frequency synthesizer dedicated to implantable medical microsystems
- 27 February 2008
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 58 (3) , 205-214
An ultra-low power ISM-band integer-N frequency synthesizer dedicated to implantable medical microsystems
- 1 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 1-4
A Fully-Integrated 580 μW ISM-Band Frequency Synthesizer for Implantable Medical Devices
In this paper, a fully integrated ultra-low power integer-N frequency synthesizer for operation in the 902-928 MHz ISM band is presented. This phase-locked loop based synthesizer contains an on-chip 1.830 GHz LC voltage controlled oscillator followed by a divide-by-2 prescaler that generates both in phase and quadrature differential carrier signals. The synthesizer was implemented using STMicroelectronics CMOS 90-nm process, consumes less than 580 μW of power at a supply voltage of 1 V and occupies an area of 0.7×0.8 mm 2 . The frequency synthesizer will be used in the transceiver of an implantable wireless sensing microsystem (IWSM) dedicated to in vivo monitoring of biological parameters.
- 1 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 1-4
A Fully-Integrated 580 μW ISM-Band Frequency Synthesizer for Implantable Medical Devices
In this paper, a fully integrated ultra-low power integer-N frequency synthesizer for operation in the 902-928 MHz ISM band is presented. This phase-locked loop based synthesizer contains an on-chip 1.830 GHz LC voltage controlled oscillator followed by a divide-by-2 prescaler that generates both in phase and quadrature differential carrier signals. The synthesizer was implemented using STMicroelectronics CMOS 90-nm process, consumes less than 580 μW of power at a supply voltage of 1 V and occupies an area of 0.7×0.8 mm 2 . The frequency synthesizer will be used in the transceiver of an implantable wireless sensing microsystem (IWSM) dedicated to in vivo monitoring of biological parameters.
- 1 December 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 494-497
Low Power SAW-Based Oscillator for an Implantable Multisensor Microsystem
The architecture of a low-power implantable multisensor microsystem dedicated to in vivo monitoring of biological parameters is presented. Low-power RF circuit techniques based on the gm/I d methodology, used to design the communication module of this biotelemetry microsystem, are discussed. A derivation of the optimal operating point of a surface-acoustic wave (SAW) oscillator is presented based on the resonator's frequency response. The low-power oscillator, implemented in a 90-nm CMOS process, is presented to illustrate the design techniques used. The oscillator draws 320 muA from a 1-V supply and the amplitude of oscillations is 200 mV
- 1 December 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 494-497
Low Power SAW-Based Oscillator for an Implantable Multisensor Microsystem
The architecture of a low-power implantable multisensor microsystem dedicated to in vivo monitoring of biological parameters is presented. Low-power RF circuit techniques based on the gm/I d methodology, used to design the communication module of this biotelemetry microsystem, are discussed. A derivation of the optimal operating point of a surface-acoustic wave (SAW) oscillator is presented based on the resonator's frequency response. The low-power oscillator, implemented in a 90-nm CMOS process, is presented to illustrate the design techniques used. The oscillator draws 320 muA from a 1-V supply and the amplitude of oscillations is 200 mV