Jonas Bartsch
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jonas Bartsch has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Stefan Glunz
Fraunhofer Institute for Solar Energy Systems ISE Freiburg Germany
3 shared publications - Sven Kluska
Fraunhofer Institute for Solar Energy Systems, Freiburg, Germany
3 shared publications C. Schetter
Fraunhofer Institute for Solar Energy Systems, 79110 Freiburg, Germany
2 shared publications- Markus Glatthaar
Fraunhofer Institute for Solar Energy Systems, Freiburg, Germany
2 shared publications A. Gombert
Fraunhofer Institute for Solar Energy Systems, 79110 Freiburg, Germany
1 shared publicationA. Mondon
Fraunhofer Institute for Solar Energy Systems, 79110 Freiburg, Germany
1 shared publication
Latest Publications
- 18 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 9 (6) , 1532-1540
Microcharacterization of Interface Oxide Layer on Laser-Structured Silicon Surfaces of Plated Ni–Cu Solar Cells
Light-induced plating on laser-structured passivation layer openings is an alternative method to silver screen printing for fabrication of the front-side metal grid on silicon solar cells. Fundamental contact properties, such as adhesion and contact resistance, are determined at the highly inhomogeneous interface of laser-structured silicon and plated nickel. Usage of laser structuring and plating holds the risk that an interfacial oxide layer is incorporated to the contact stack. It is shown within this article that both native and laser-induced oxide formation influence contact properties. Although, a native oxide layer does not impede metal deposition during plating, the dynamics of the layer formation is shown to be changed. It is known that interface oxides harm the contact resistance, and it is reported that postplating annealing decreases the contact resistance. In this article, the microstructural basis of the temperature-induced changes is examined. By transmission electron microscopy and energy dispersive X-ray spectroscopy, no temperature-induced modification of the interface microstructure, such as silicide formation or metal-induced crystallization of the amorphous surface, is observed. Results suggest that the decrease is attributed to a temperature-induced change of the electrical properties of the interface oxide. Considering reports that partially closed interface oxide layers are an inherent feature of laser-structured plated contacts, the results presented motivate reconsidering the objective of postplating annealing. The results indicate that the beneficial impact of silicide formation is overrated for the case of laser-structured plated contacts, whereas the temperature-induced modifications on residual interface oxide layers are neglected in the scientific discussions on the given contact stack.
- 18 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 9 (6) , 1532-1540
Microcharacterization of Interface Oxide Layer on Laser-Structured Silicon Surfaces of Plated Ni–Cu Solar Cells
Light-induced plating on laser-structured passivation layer openings is an alternative method to silver screen printing for fabrication of the front-side metal grid on silicon solar cells. Fundamental contact properties, such as adhesion and contact resistance, are determined at the highly inhomogeneous interface of laser-structured silicon and plated nickel. Usage of laser structuring and plating holds the risk that an interfacial oxide layer is incorporated to the contact stack. It is shown within this article that both native and laser-induced oxide formation influence contact properties. Although, a native oxide layer does not impede metal deposition during plating, the dynamics of the layer formation is shown to be changed. It is known that interface oxides harm the contact resistance, and it is reported that postplating annealing decreases the contact resistance. In this article, the microstructural basis of the temperature-induced changes is examined. By transmission electron microscopy and energy dispersive X-ray spectroscopy, no temperature-induced modification of the interface microstructure, such as silicide formation or metal-induced crystallization of the amorphous surface, is observed. Results suggest that the decrease is attributed to a temperature-induced change of the electrical properties of the interface oxide. Considering reports that partially closed interface oxide layers are an inherent feature of laser-structured plated contacts, the results presented motivate reconsidering the objective of postplating annealing. The results indicate that the beneficial impact of silicide formation is overrated for the case of laser-structured plated contacts, whereas the temperature-induced modifications on residual interface oxide layers are neglected in the scientific discussions on the given contact stack.
- 10 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1999 (1) , 110005
Development and characterization of multifunctional PECVD SiNX:P layers for laser-doped selective emitters
We apply stacks of silicon nitride (SiNX) layers consisting of phosphorus-doped SiNX (SiNX:P) and undoped SiNX as first and second layer, on the front surface of p-type monocrystalline silicon passivated emitter and rear cells (PERC). The stack is deposited using plasma-enhanced chemical vapor deposition. These layer stacks provide excellent surface passivation and anti-reflection properties comparable to single undoped SiNX layers. A laser processing locally introduces the phosphorus dopants from the SiNX:P/SiNX layer stack into the silicon and locally removes the layer stack. Thereby, local highly doped areas with sheet resistances as low as Rsh ≈ 20 Ω/sq are obtained. We refer to this as the nPassDop approach, which provides local high doping and structuring of the anti-reflection coating in one process. The saturation current density of the laser processed areas is estimated to be as low as j0,laser ≈ 500 fA/cm2. First implementations for large-area p-type Cz-Si PERC cells with self-aligned NiCuAg plated front contacts yield an energy conversion efficiency of 19.6%.
- 10 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1999 (1) , 110005
Development and characterization of multifunctional PECVD SiNX:P layers for laser-doped selective emitters
We apply stacks of silicon nitride (SiNX) layers consisting of phosphorus-doped SiNX (SiNX:P) and undoped SiNX as first and second layer, on the front surface of p-type monocrystalline silicon passivated emitter and rear cells (PERC). The stack is deposited using plasma-enhanced chemical vapor deposition. These layer stacks provide excellent surface passivation and anti-reflection properties comparable to single undoped SiNX layers. A laser processing locally introduces the phosphorus dopants from the SiNX:P/SiNX layer stack into the silicon and locally removes the layer stack. Thereby, local highly doped areas with sheet resistances as low as Rsh ≈ 20 Ω/sq are obtained. We refer to this as the nPassDop approach, which provides local high doping and structuring of the anti-reflection coating in one process. The saturation current density of the laser processed areas is estimated to be as low as j0,laser ≈ 500 fA/cm2. First implementations for large-area p-type Cz-Si PERC cells with self-aligned NiCuAg plated front contacts yield an energy conversion efficiency of 19.6%.
- 10 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1999 (1) , 040009
Novel mask-less plating metallization route for bifacial silicon heterojunction solar cells
The proof of concept of a novel metallization route for bifacial silicon heterojunction (SHJ) solar cells by selective plating – i.e. organic mask-free, is demonstrated by a first lab scale solar cell (η=15.5%). A patterned metal-seed is inkjet-printed or deposited by PVD on a PVD-Al layer covering the ITO layer. The copper electroplating process is investigated considering different electrolytes and plating settings in order to selectively cover the metal-seed and not the PVD Al layer. As well a processing chemistry to etch the PVD-Al layer without affecting the ITO and the electroplated contact is presented.
- 10 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1999 (1) , 040009
Novel mask-less plating metallization route for bifacial silicon heterojunction solar cells
The proof of concept of a novel metallization route for bifacial silicon heterojunction (SHJ) solar cells by selective plating – i.e. organic mask-free, is demonstrated by a first lab scale solar cell (η=15.5%). A patterned metal-seed is inkjet-printed or deposited by PVD on a PVD-Al layer covering the ITO layer. The copper electroplating process is investigated considering different electrolytes and plating settings in order to selectively cover the metal-seed and not the PVD Al layer. As well a processing chemistry to etch the PVD-Al layer without affecting the ITO and the electroplated contact is presented.
- 1 January 2011
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 158 (6) , H651-H658
Effects of Seed Layer and Substrate Morphology on Solar Cell Contacts Deposited by Light-Induced Plating
To improve two-step metallization processes for silicon solar cells, the influence of different seed layers and surface textures on the light-induced plating (LIP) deposition behaviour at different plating rates has been studied. Typical seed layers of screen- and aerosol printed silver paste have been tested on alkaline (random pyramid) and acidic texture. Silver deposition at high rate has been found to be problematic on very thin aerosol printed layers, especially for alkaline texture with high roughness. In an attempt to obtain high process speed while maintaining high conductivity, aerosol seed layers were subjected to different multi-step plating processes. Morphological features (aerosol particles, alkaline texture) were leveled by a slow pre-plating step. In a second plating step, the deposition rate was varied. The results were compared to similar experiments with untreated aerosol seed layers. Both pre-plating steps were found to effectively improve the deposition quality of the second plating step with high plating rate, and to improve the process robustness. On acidic texture (multicrystalline solar cells), high plating rates were found to give better qualities compared to random pyramids, even without pre-treatment. Both behaviours are attributed to differences in local field and current density between sharply and smoothly shaped plating bases.
- 1 January 2011
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 158 (6) , H651-H658
Effects of Seed Layer and Substrate Morphology on Solar Cell Contacts Deposited by Light-Induced Plating
To improve two-step metallization processes for silicon solar cells, the influence of different seed layers and surface textures on the light-induced plating (LIP) deposition behaviour at different plating rates has been studied. Typical seed layers of screen- and aerosol printed silver paste have been tested on alkaline (random pyramid) and acidic texture. Silver deposition at high rate has been found to be problematic on very thin aerosol printed layers, especially for alkaline texture with high roughness. In an attempt to obtain high process speed while maintaining high conductivity, aerosol seed layers were subjected to different multi-step plating processes. Morphological features (aerosol particles, alkaline texture) were leveled by a slow pre-plating step. In a second plating step, the deposition rate was varied. The results were compared to similar experiments with untreated aerosol seed layers. Both pre-plating steps were found to effectively improve the deposition quality of the second plating step with high plating rate, and to improve the process robustness. On acidic texture (multicrystalline solar cells), high plating rates were found to give better qualities compared to random pyramids, even without pre-treatment. Both behaviours are attributed to differences in local field and current density between sharply and smoothly shaped plating bases.
- 1 January 2010
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 157 (10) , H942-H946
Quick Determination of Copper-Metallization Long-Term Impact on Silicon Solar Cells
In this paper, we present a method to quickly evaluate the long-term effects of copper-containing metal stack systems for silicon solar cell front–side metallization. Copper diffusion, which is detrimental for the solar cell performance, is accelerated by exposing the cell to thermal stress. In this paper, we suggest to quantify the degree of copper diffusion into the cell by the very fast Suns- VOCVOC technique, measuring the pseudo fill factor (pFF). Using three or more different temperatures, and assuming a certain loss in pFF corresponds to a certain depth of diffusion, the effective activation energy for copper diffusion for a given system can be extracted from an Arrhenius plot of the measured data. An extrapolation into temperature regions typical for solar cell modules under outdoor conditions allows an estimation of the fill factor loss for any operation time and temperature. Compared to time- and cost-intensive methods such as transmission electron microscopy or secondary-ion mass spectrometry, this kind of investigation requires only sparse equipment and can typically be done in 1 week per stack system.
- 1 January 2010
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 157 (10) , H942-H946
Quick Determination of Copper-Metallization Long-Term Impact on Silicon Solar Cells
In this paper, we present a method to quickly evaluate the long-term effects of copper-containing metal stack systems for silicon solar cell front–side metallization. Copper diffusion, which is detrimental for the solar cell performance, is accelerated by exposing the cell to thermal stress. In this paper, we suggest to quantify the degree of copper diffusion into the cell by the very fast Suns- VOCVOC technique, measuring the pseudo fill factor (pFF). Using three or more different temperatures, and assuming a certain loss in pFF corresponds to a certain depth of diffusion, the effective activation energy for copper diffusion for a given system can be extracted from an Arrhenius plot of the measured data. An extrapolation into temperature regions typical for solar cell modules under outdoor conditions allows an estimation of the fill factor loss for any operation time and temperature. Compared to time- and cost-intensive methods such as transmission electron microscopy or secondary-ion mass spectrometry, this kind of investigation requires only sparse equipment and can typically be done in 1 week per stack system.
- 15 December 2009
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 40 (4) , 757-765
Electrochemical methods to analyse the light-induced plating process
- 15 December 2009
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 40 (4) , 757-765
Electrochemical methods to analyse the light-induced plating process