Guo‐Hua Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Guo‐Hua Hu has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Cai‐Liang Zhang
State Key Laboratory of Chemical Engineering, Department of Chemical and Biological Engineering, Zhejiang University, 310027 Hangzhou, China
1 shared publication- Dean Shi
Department of Physics and Materials Science, City University of Hong Kong, Kowloon, Hong Kong, People's Republic of China
1 shared publication Huxi Li
Laboratoire des sciencs du génie chimique CNRS‐ENSIC‐INPL 1 rue Grandville BP 451, 54001 Nancy Cedex, France
1 shared publicationJinghua Yin
State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, People's Republic of China
1 shared publicationLian‐Fang Feng
Laboratory of chemical engineering sciences, CNRS‐ENSIC‐INPL, 1 rue Grandville, BP 451, 54001 Nancy, France
1 shared publication- Lian‐Fang Feng
Institute of Zhejiang University-Quzhou, Quzhou 324000, China
1 shared publication
Latest Publications
- 30 August 2010
- Published by Wiley in Polymer Engineering & Science
- Vol. 50 (11) , 2243-2251
Blend composition dependence of the compatibilizing efficiency of graft copolymers for immiscible polymer blends
This work is concerned with the dependence of the compatibilizing efficiency of graft copolymers on the composition of immiscible polymer blends. A series of graft copolymers of polystyrene (PS) and polyamide 6 (PA6), denoted as PS‐g‐PA6, with different molecular structures were used as compatibilizers. The PS‐g‐PA6 was more efficient for the PS/PA6 (80/20) blend than for the PS/PA6 (20/80) one, indicating that a graft copolymer whose backbone and grafts match the matrix and the disperse phase polymers, respectively, has higher compatibilizing efficiency. This is in disagreement with the literature. Moreover, whatever the blend composition, for PS‐g‐PA6 graft copolymers with the same backbone and the same number of grafts per backbone, the longer the grafts, the higher their compatibilizing and stabilizing efficiency; for a given backbone/graft mass ratio, the longer the grafts and concomitantly the smaller the number of grafts per backbone, the higher the compatibilizing and stabilizing efficiency of the graft copolymer. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers
- 30 August 2010
- Published by Wiley in Polymer Engineering & Science
- Vol. 50 (11) , 2243-2251
Blend composition dependence of the compatibilizing efficiency of graft copolymers for immiscible polymer blends
This work is concerned with the dependence of the compatibilizing efficiency of graft copolymers on the composition of immiscible polymer blends. A series of graft copolymers of polystyrene (PS) and polyamide 6 (PA6), denoted as PS‐g‐PA6, with different molecular structures were used as compatibilizers. The PS‐g‐PA6 was more efficient for the PS/PA6 (80/20) blend than for the PS/PA6 (20/80) one, indicating that a graft copolymer whose backbone and grafts match the matrix and the disperse phase polymers, respectively, has higher compatibilizing efficiency. This is in disagreement with the literature. Moreover, whatever the blend composition, for PS‐g‐PA6 graft copolymers with the same backbone and the same number of grafts per backbone, the longer the grafts, the higher their compatibilizing and stabilizing efficiency; for a given backbone/graft mass ratio, the longer the grafts and concomitantly the smaller the number of grafts per backbone, the higher the compatibilizing and stabilizing efficiency of the graft copolymer. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers
- 23 August 2006
- Published by Wiley in Polymer Engineering & Science
- Vol. 46 (10) , 1443-1454
Nano‐reactors for controlling the selectivity of the free radical grafting of maleic anhydride onto polypropylene in the melt
This paper reports on a successful application of the concept of nanoreactors to effectively controlling the selectivity of the free radical grafting of maleic anhydride (MAH) onto polypropylene (PP) in the melt, an industrially relevant process. More specifically, a free radical initiator of type ROOR was first confined into (or encapsulated by) the galleries of an organically modified montmorillonite (o‐MMT) whose interdistance was 2.4 nm. Primary free radicals (RO ·) formed inside the o‐MMT galleries had to diffuse out before they could react with the PP backbone. The controlled release of the primary free radicals significantly increased the grafting degree of MAH onto PP and greatly reduced the level of the chain scission of the latter. Those results were better understood by electron spin resonance studies on model systems and by Monte Carlo simulations. POLYM. ENG. SCI. 46:1443–1454, 2006. © 2006 Society of Plastics Engineers.
- 23 August 2006
- Published by Wiley in Polymer Engineering & Science
- Vol. 46 (10) , 1443-1454
Nano‐reactors for controlling the selectivity of the free radical grafting of maleic anhydride onto polypropylene in the melt
This paper reports on a successful application of the concept of nanoreactors to effectively controlling the selectivity of the free radical grafting of maleic anhydride (MAH) onto polypropylene (PP) in the melt, an industrially relevant process. More specifically, a free radical initiator of type ROOR was first confined into (or encapsulated by) the galleries of an organically modified montmorillonite (o‐MMT) whose interdistance was 2.4 nm. Primary free radicals (RO ·) formed inside the o‐MMT galleries had to diffuse out before they could react with the PP backbone. The controlled release of the primary free radicals significantly increased the grafting degree of MAH onto PP and greatly reduced the level of the chain scission of the latter. Those results were better understood by electron spin resonance studies on model systems and by Monte Carlo simulations. POLYM. ENG. SCI. 46:1443–1454, 2006. © 2006 Society of Plastics Engineers.
- 3 July 2003
- Published by Wiley in Macromolecular Symposia
- Vol. 195 (1) , 303-308
Extruder processing for nanoblends and nanocomposites
Structuring multiphase polymer materials to a micrometer scale (micro‐structuration) is a facile engineering practice. However, structuring them to a nanometer scale (nano‐structuration) is a formidable engineering challenge. In this paper, it is shown first why traditional extruder compounding processes only lead to micro‐structuration and then how one may use the extruder type of mixer to structure multiphase polymer materials at a nano‐meter scale to obtain nanostructured polymer blends (nanoblends) and nanostructured polymer composites (nanocomposites).
- 3 July 2003
- Published by Wiley in Macromolecular Symposia
- Vol. 195 (1) , 303-308
Extruder processing for nanoblends and nanocomposites
Structuring multiphase polymer materials to a micrometer scale (micro‐structuration) is a facile engineering practice. However, structuring them to a nanometer scale (nano‐structuration) is a formidable engineering challenge. In this paper, it is shown first why traditional extruder compounding processes only lead to micro‐structuration and then how one may use the extruder type of mixer to structure multiphase polymer materials at a nano‐meter scale to obtain nanostructured polymer blends (nanoblends) and nanostructured polymer composites (nanocomposites).
- 1 May 2001
- Published by Wiley in Polymer Engineering & Science
- Vol. 41 (5) , 763-770
A two‐zone melting model for polymer blends in a batch mixer
The rate of the morphology development of immiscible polymer blends is closely related to the rates of melting of the polymer constituents. A two‐zone model was developed to describe the rate of melting of the polymer pellets of mixtures of two semicrystalline polymers in an internal batch mixer. The mixing chamber was divided into two zones: high temperature and high shear zone, and low temperature and low shear zone. Melting was assumed to occur mainly in the first zone. Moreover, pellets were assumed to be spherical, and melting proceeded from the outersurface to the core in a gradual manner. For a given pellet, the rate of melting depended, among other things, upon the number of passes through the high shear and high temperature zone and the time it experiences therein. The validity of the model was confirmed experimentally in terms of the number and weight fraction of solid pellets as a function of mixing time.
- 1 May 2001
- Published by Wiley in Polymer Engineering & Science
- Vol. 41 (5) , 763-770
A two‐zone melting model for polymer blends in a batch mixer
The rate of the morphology development of immiscible polymer blends is closely related to the rates of melting of the polymer constituents. A two‐zone model was developed to describe the rate of melting of the polymer pellets of mixtures of two semicrystalline polymers in an internal batch mixer. The mixing chamber was divided into two zones: high temperature and high shear zone, and low temperature and low shear zone. Melting was assumed to occur mainly in the first zone. Moreover, pellets were assumed to be spherical, and melting proceeded from the outersurface to the core in a gradual manner. For a given pellet, the rate of melting depended, among other things, upon the number of passes through the high shear and high temperature zone and the time it experiences therein. The validity of the model was confirmed experimentally in terms of the number and weight fraction of solid pellets as a function of mixing time.