Qing Guo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qing Guo has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Kuang Sheng
Zhejiang University
5 shared publications - Na Ren
Zhejiang University
5 shared publications - Hongyi Xu
College of Electrical Engineering, Zhejiang University, Hangzhou, China
2 shared publications - Jiupeng Wu
College of Electrical Engineering, Zhejiang University, Hangzhou, China
2 shared publications Kuang Sheng
College of Electrical Engineering, Zhejiang University, Hangzhou, PR China
2 shared publications- Maosheng Zhang
College of Electrical Engineering, Zhejiang University, Hangzhou 310027, China
2 shared publications
Latest Publications
- 20 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (10) , 6221-6227
Modeling of the Influence on Effective VTH From Interface States, Short Channel Effects, and Contact Resistance in SiC MOSFETs
The poor interface of silicon carbide (SiC)/SiO $_{\text{2}}$ combined with the short channel effects (SCEs) and source contact resistance, collectively impacts the effective threshold voltage in SiC MOSFETs. In this work, a physical discrete channel model was proposed to analyze the influence of the combined effects of varying channel lengths, as well as applied drain and gate voltages. The proposed model was validated through TCAD simulation and by the fabricated SiC power MOSFETs. This model was applicable to MOSFETs with both symmetric and asymmetric channels considering various interface state density distributions. The influence of these factors on effective threshold voltage was also discussed considering variations in source contact resistance and channel doping concentration. Through the analysis of the model results, it was found that the interface states significantly impact the effective threshold voltage through different mechanisms while the SCEs are mitigated by the unsaturated interface states.
- 20 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (10) , 6221-6227
Modeling of the Influence on Effective VTH From Interface States, Short Channel Effects, and Contact Resistance in SiC MOSFETs
The poor interface of silicon carbide (SiC)/SiO $_{\text{2}}$ combined with the short channel effects (SCEs) and source contact resistance, collectively impacts the effective threshold voltage in SiC MOSFETs. In this work, a physical discrete channel model was proposed to analyze the influence of the combined effects of varying channel lengths, as well as applied drain and gate voltages. The proposed model was validated through TCAD simulation and by the fabricated SiC power MOSFETs. This model was applicable to MOSFETs with both symmetric and asymmetric channels considering various interface state density distributions. The influence of these factors on effective threshold voltage was also discussed considering variations in source contact resistance and channel doping concentration. Through the analysis of the model results, it was found that the interface states significantly impact the effective threshold voltage through different mechanisms while the SCEs are mitigated by the unsaturated interface states.
- Open Access
The Impact of Process Conditions on Surge Current Capability of 1.2 kV SiC JBS and MPS Diodes
This paper demonstrated the impact of process conditions on the surge current capability of 1.2 kV SiC junction barrier Schottky diode (JBS) and merged PiN Schottky diode (MPS). The influence of ohmic contact and defect density produced by implantation was studied in the simulation. The device fabricated with high temperature implantation had less defect density in the implant region compared with room temperature implantation, which contributed to higher hole injection in surge current mode and 20% surge capability improvement. In addition, with lower P+ ohmic contact resistance, the device had higher surge capability. When compared to device fabrication with a single Schottky metal layer in the device active area, adding additional P+ ohmic contact on top of the P+ regions in the device active area resulted in the pn junctions sharing a greater portion of surge current, and improved the devices’ surge capability by ~10%.
Open AccessThe Impact of Process Conditions on Surge Current Capability of 1.2 kV SiC JBS and MPS Diodes
This paper demonstrated the impact of process conditions on the surge current capability of 1.2 kV SiC junction barrier Schottky diode (JBS) and merged PiN Schottky diode (MPS). The influence of ohmic contact and defect density produced by implantation was studied in the simulation. The device fabricated with high temperature implantation had less defect density in the implant region compared with room temperature implantation, which contributed to higher hole injection in surge current mode and 20% surge capability improvement. In addition, with lower P+ ohmic contact resistance, the device had higher surge capability. When compared to device fabrication with a single Schottky metal layer in the device active area, adding additional P+ ohmic contact on top of the P+ regions in the device active area resulted in the pn junctions sharing a greater portion of surge current, and improved the devices’ surge capability by ~10%.
- Open Access
Understanding Turn-On Transients of SiC High-Power Modules: Drain-Source Voltage Plateau Characteristics
The SiC (silicon carbide) high-power module has great potential to replace the IGBT (insulated gate bipolar transistor) power module in high-frequency and high-power applications, due to the superior properties of fast switching and low power loss, however, when the SiC high-power module operates under inappropriate conditions, the advantages of the SiC high-power module will be probably eliminated. In this paper, four kinds of SiC high-power modules are fabricated to investigate fast switching performance. The variations in characteristics of drain-source voltage at turn-on transient under the combined conditions of multiple factors are studied. A characteristic of voltage plateau is observed from the drain-source voltage waveform at turn-on transient in the experiments, and the characteristic is reproduced by simulation. The mechanism behind the voltage plateau is studied, and it is revealed that the characteristic of drain-source voltage plateau is a reflection of the miller plateau effect of gate-source voltage on drain-source voltage under the combined conditions of fast turn-on speed and low DC bus voltage, while the different values of drain-source voltage plateau are attributed to the discrepancy of structure between upper-side and lower-side in the corresponding partial path of the drain circuit loop inside the module, with the standard 62 mm package outline.
Open AccessUnderstanding Turn-On Transients of SiC High-Power Modules: Drain-Source Voltage Plateau Characteristics
The SiC (silicon carbide) high-power module has great potential to replace the IGBT (insulated gate bipolar transistor) power module in high-frequency and high-power applications, due to the superior properties of fast switching and low power loss, however, when the SiC high-power module operates under inappropriate conditions, the advantages of the SiC high-power module will be probably eliminated. In this paper, four kinds of SiC high-power modules are fabricated to investigate fast switching performance. The variations in characteristics of drain-source voltage at turn-on transient under the combined conditions of multiple factors are studied. A characteristic of voltage plateau is observed from the drain-source voltage waveform at turn-on transient in the experiments, and the characteristic is reproduced by simulation. The mechanism behind the voltage plateau is studied, and it is revealed that the characteristic of drain-source voltage plateau is a reflection of the miller plateau effect of gate-source voltage on drain-source voltage under the combined conditions of fast turn-on speed and low DC bus voltage, while the different values of drain-source voltage plateau are attributed to the discrepancy of structure between upper-side and lower-side in the corresponding partial path of the drain circuit loop inside the module, with the standard 62 mm package outline.
- Open Access
A Comparative Study of Silicon Carbide Merged PiN Schottky Diodes with Electrical-Thermal Coupled Considerations
A comparative study of surge current reliability of 1200 V/5 A 4H-SiC (silicon carbide) MPS (Merged PiN Schottky) diodes with different technologies is presented. The influences of device designs in terms of electrical and thermal aspects on the forward conduction performance and surge current capability were studied. Device forward characteristics were simulated and measured. Standard single-pulse surge current tests and thermal impedance measurements were carried to show their surge capability and thermal design differences. An advanced thermal RC (thermal resistance-capacitance) model, with the consideration of current distribution non-uniformity effects, is proposed to accurately calculate the device junction temperature during surge events. It was found that a thinner substrate and a hexagonal layout design are beneficial to the improvement of the bipolar conduction performance in high current mode, as well as the surge current capability. The thinner substrate design also has advantages on thermal aspects, as it presents the lowest thermal resistance. The calculated failure temperature during the surge tests is consistent with the aluminum melting phenomenon, which is regarded as the failure mechanism. It was demonstrated that, for a SiC MPS diode, higher bipolar conduction performance is conducive to restraining the joule heat, and a lower thermal resistance design is able to accelerate the heat dissipation and limit the junction temperature during surge events. In this way, the MPS diode using a thinner substrate and advanced layout design technology is able to achieve 60% higher surge current density capability compared to the other technologies.
Open AccessA Comparative Study of Silicon Carbide Merged PiN Schottky Diodes with Electrical-Thermal Coupled Considerations
A comparative study of surge current reliability of 1200 V/5 A 4H-SiC (silicon carbide) MPS (Merged PiN Schottky) diodes with different technologies is presented. The influences of device designs in terms of electrical and thermal aspects on the forward conduction performance and surge current capability were studied. Device forward characteristics were simulated and measured. Standard single-pulse surge current tests and thermal impedance measurements were carried to show their surge capability and thermal design differences. An advanced thermal RC (thermal resistance-capacitance) model, with the consideration of current distribution non-uniformity effects, is proposed to accurately calculate the device junction temperature during surge events. It was found that a thinner substrate and a hexagonal layout design are beneficial to the improvement of the bipolar conduction performance in high current mode, as well as the surge current capability. The thinner substrate design also has advantages on thermal aspects, as it presents the lowest thermal resistance. The calculated failure temperature during the surge tests is consistent with the aluminum melting phenomenon, which is regarded as the failure mechanism. It was demonstrated that, for a SiC MPS diode, higher bipolar conduction performance is conducive to restraining the joule heat, and a lower thermal resistance design is able to accelerate the heat dissipation and limit the junction temperature during surge events. In this way, the MPS diode using a thinner substrate and advanced layout design technology is able to achieve 60% higher surge current density capability compared to the other technologies.
- Open Access
- 18 December 2019
- Published by MDPI AG in Micromachines
- Vol. 11 (1) , 5
Modeling and Analysis of vgs Characteristics for Upper-Side and Lower-Side Switches at Turn-on Transients for a 1200V/200A Full-SiC Power Module
In this work, a 1200V/200A full-SiC half-bridge power module was fabricated for high-power high-frequency application, and the characteristics of gate-source voltage ( ) at turn-on transient under different output power was investigated via experiments, modeling, and simulation. Also, the comparison of the characteristics between the upper-side and lower-side was conducted. From experiments, the characteristics show negative spike issue and it becomes severe under higher output power conditions. On the other hand, the upper-side and lower-side show different characteristics, namely, the spike of upper-side is superimposed by a 83.3 MHz high frequency oscillation during the process of being pulled down, while the spike of lower-side contains no oscillation. The mechanisms behind the influence of output power on the spike characteristics and their difference between the upper-side and lower-side were studied via modeling and simulation. Equivalent RLC (resistance-inductance-capacitance) circuit models were proposed and established for the gate driver loops of the upper-side and lower-side based on the internal structure of the power module. With the help of the proposed models, characteristics of the upper-side and lower-side were simulated and compared with the experimental results. The trend of changes in the pulling-down and oscillation amplitude along with the increasing output power from simulation are consistent with that of the experimental results. In addition, different conditions of gate resistance for the SiC power module are compared. Through the comparison between the experiments and simulations, the validity of the proposed equivalent RLC circuit model and the rationality of the analysis about the mechanisms behind the characteristics at turn-on transient for SiC half-bridge power module are confirmed.- 18 December 2019
- Published by MDPI AG in Micromachines
- Vol. 11 (1) , 5
Open AccessModeling and Analysis of vgs Characteristics for Upper-Side and Lower-Side Switches at Turn-on Transients for a 1200V/200A Full-SiC Power Module
In this work, a 1200V/200A full-SiC half-bridge power module was fabricated for high-power high-frequency application, and the characteristics of gate-source voltage ( ) at turn-on transient under different output power was investigated via experiments, modeling, and simulation. Also, the comparison of the characteristics between the upper-side and lower-side was conducted. From experiments, the characteristics show negative spike issue and it becomes severe under higher output power conditions. On the other hand, the upper-side and lower-side show different characteristics, namely, the spike of upper-side is superimposed by a 83.3 MHz high frequency oscillation during the process of being pulled down, while the spike of lower-side contains no oscillation. The mechanisms behind the influence of output power on the spike characteristics and their difference between the upper-side and lower-side were studied via modeling and simulation. Equivalent RLC (resistance-inductance-capacitance) circuit models were proposed and established for the gate driver loops of the upper-side and lower-side based on the internal structure of the power module. With the help of the proposed models, characteristics of the upper-side and lower-side were simulated and compared with the experimental results. The trend of changes in the pulling-down and oscillation amplitude along with the increasing output power from simulation are consistent with that of the experimental results. In addition, different conditions of gate resistance for the SiC power module are compared. Through the comparison between the experiments and simulations, the validity of the proposed equivalent RLC circuit model and the rationality of the analysis about the mechanisms behind the characteristics at turn-on transient for SiC half-bridge power module are confirmed. - 30 June 2013
- Published by Elsevier in Microelectronics Reliability
- Vol. 53 (12) , 1848-1856
High temperature physical modeling and verification of a novel 4H-SiC lateral JFET structure
- 30 June 2013
- Published by Elsevier in Microelectronics Reliability
- Vol. 53 (12) , 1848-1856
High temperature physical modeling and verification of a novel 4H-SiC lateral JFET structure
- 1 November 2011
- Published by IOP Publishing in Chinese Physics Letters
- Vol. 28 (11) , 117302
The Tunable Bandgap of AB-Stacked Bilayer Graphene on SiO 2 with H 2 O Molecule Adsorption
The atomic and electronic structures of AB-stacking bilayer graphene (BLG) in the presence of H2O molecules are investigated by density functional theory calculations. For free-standing BLG, the bandgap is opened to 0.101 eV with a single H2O molecule adsorbed on its surface. The perfectly suspended BLG is sensitive to H2O adsorbates, which break the BLG lattice symmetry and open an energy gap. While a single H2O molecule is adsorbed on the BLG surface with a SiO2 substrate, the bandgap widens to 0.363 eV. Both the H2O molecule adsorption and the oxide substrate contribute to the BLG bandgap opening. The phenomenon is interpreted with the charge transfer process in 2D carbon nanostructures.
- 1 November 2011
- Published by IOP Publishing in Chinese Physics Letters
- Vol. 28 (11) , 117302
The Tunable Bandgap of AB-Stacked Bilayer Graphene on SiO 2 with H 2 O Molecule Adsorption
The atomic and electronic structures of AB-stacking bilayer graphene (BLG) in the presence of H2O molecules are investigated by density functional theory calculations. For free-standing BLG, the bandgap is opened to 0.101 eV with a single H2O molecule adsorbed on its surface. The perfectly suspended BLG is sensitive to H2O adsorbates, which break the BLG lattice symmetry and open an energy gap. While a single H2O molecule is adsorbed on the BLG surface with a SiO2 substrate, the bandgap widens to 0.363 eV. Both the H2O molecule adsorption and the oxide substrate contribute to the BLG bandgap opening. The phenomenon is interpreted with the charge transfer process in 2D carbon nanostructures.