Shigeru Takaya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shigeru Takaya has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Kenzo Miya
International Institute of Universality , Imon Ikenohata Bldg. 7F, 2-7-17, Ikenohata, Taito, Tokyo, 110-0008, Japan
2 shared publications Takayuki Suzuki
Advanced Materials and Structural Integrity Group, Institute of Mechanical Systems Engineering, National Institute of Advanced Industrial Science and Technology, 1-2-1 Namiki, Tsukuba-shi, Ibaraki-ken 305-8564, Japan
2 shared publicationsKazuyuki Demachi
Nuclear Engineering Research Laboratory, School of Engineering, The University of Tokyo, 2-22 Shirakata Shirane, Tokai-mura, Naka-gun, Ibaraki-ken 319-1188, Japan
1 shared publicationMitsuru Uesaka
Nuclear Engineering Research Laboratory, School of Engineering, The University of Tokyo, 2-22 Shirakata Shirane, Tokai-mura, Naka-gun, Ibaraki-ken 319-1188, Japan
1 shared publication- Tetsuya Uchimoto
Institute of Fluid Science, Tohoku University, Sendai, Miyagi, Japan
1 shared publication Yoshihiro Matsumoto
Nuclear Fuel Industries Ltd., 950 Noda, Kumadori-cho, Sennan-gun, Osaka-fu 590-0481, Japan
1 shared publication
Latest Publications
- 10 April 2005
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 161 (1-2) , 66-74
Application of magnetic phenomena to analysis of stress corrosion cracking in welded part of stainless steel
- 10 April 2005
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 161 (1-2) , 66-74
Application of magnetic phenomena to analysis of stress corrosion cracking in welded part of stainless steel
- 1 April 2004
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 327 (1) , 19-26
Estimation of stress corrosion cracking sensitivity of type 304 stainless steel by magnetic force microscope
- 1 April 2004
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 327 (1) , 19-26
Estimation of stress corrosion cracking sensitivity of type 304 stainless steel by magnetic force microscope
- 15 May 2002
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 91 (10) , 7011-7013
Magnetic force microscopy observation of sensitized Inconel 600
An application of magnetic force microscopes (MFM) is proposed to the characterization of sensitized Inconel 600 alloy with submicron order accuracy. The magnetic microstructures of Inconel 600 sensitized at for various heat treatment periods were observed by means of a MFM. MFM images show semicontinuous morphologies of the magnetizations near and at grain boundaries. The absolute value of the MFM signal, the phase shift between the oscillation of the cantilever and the piezoelectric actuator, at the grain boundary increases at first and then decreases with increasing heat treatment time, while the full width at half maximum about the MFM signals across the grain boundary increases continuously. These results coincide with the fact that the chromium content decreases at first due to production of the chromium carbide and then increase slightly due to the change in the activities of carbon and chromium near the grain boundaries. This method is useful because MFMs enable very high spatial resolution observations with minimal sample preparation and relatively easy operations.- 15 May 2002
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 91 (10) , 7011-7013
Magnetic force microscopy observation of sensitized Inconel 600
An application of magnetic force microscopes (MFM) is proposed to the characterization of sensitized Inconel 600 alloy with submicron order accuracy. The magnetic microstructures of Inconel 600 sensitized at for various heat treatment periods were observed by means of a MFM. MFM images show semicontinuous morphologies of the magnetizations near and at grain boundaries. The absolute value of the MFM signal, the phase shift between the oscillation of the cantilever and the piezoelectric actuator, at the grain boundary increases at first and then decreases with increasing heat treatment time, while the full width at half maximum about the MFM signals across the grain boundary increases continuously. These results coincide with the fact that the chromium content decreases at first due to production of the chromium carbide and then increase slightly due to the change in the activities of carbon and chromium near the grain boundaries. This method is useful because MFMs enable very high spatial resolution observations with minimal sample preparation and relatively easy operations.