KSKenjiro Sugio

Kenjiro Sugio

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kenjiro Sugio has a total of 78 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Spatially heterogeneous precipitation in ultrafine-grained SiCₚ/6061 Al composites processed by accumulative roll bonding and aging

    by Lin Zeng, Zhefeng Xu, Yujiao Ke, Kenjiro Sugio, Kazuhiro Matsugi, Hui Yu, Bohan Zhang, Gong Li, Gen Sasaki

  • Open Access

    Machine Learning-Based Prediction and Interpretation of Hot-Tearing Susceptibility in Al–Zn–Mg Alloys for Direct-Chill Casting Process Optimization

    by Yoshikazu Hayashi, Kenjiro Sugio, Gen Sasaki, Masato Okuno

    Hot tearing limits the yield of Al–Zn–Mg billets produced by direct-chill casting. Its governing factors span composition, cooling conditions and the state of the partially solidified metal, and they interact; several quantities required by physics-based criteria cannot be measured during casting, and the factors are seldom observed together at plant scale. Machine learning was therefore used to establish, from variables that are recorded in production, which factors govern hot tearing when composition and process conditions vary simultaneously. Hot tearing was assessed in 108 pilot-scale billets covering several variants, and models were trained on alloy composition, casting parameters and calculated solidification characteristics. Evaluation used nested cross-validation with whole composition clusters held out, so that performance reflects unseen variants; the selected model attained a pooled out-of-fold average precision of 0.63 against a no-skill level of 0.51. Shapley additive explanations identified Si, Mn, Zn and steady-state casting speed as the dominant variables; the effect of Si depended on Fe content and that of Mg was non-monotonic. The contribution of Mn has not been documented systematically in this system. Attribution of the model yielded relations consistent with previously reported experimental findings, and these relations rest on variables obtainable in production, providing a basis for optimizing alloy design and casting processes.

  • Microstructure and Mechanical Properties of Tungsten Fiber-Reinforced Composites Fabricated by Spark Plasma Sintering

    by Hong Huiseong, Kenjiro Sugio, Gen Sasaki

    Tungsten has attracted considerable attention as a candidate material for plasma-facing components in future fusion reactors due to its superior high-temperature strength and plasma erosion resistance. However, its inherent brittleness and crack formation under operating conditions remain critical issues, often leading to premature failure and limiting its lifetime. In this study, tungsten matrix composites reinforced with both short and long tungsten fibers were fabricated using spark plasma sintering (SPS) to improve fracture toughness and mechanical stability. The relative densities of bulk tungsten sintered at 1300 °C was measured to be 93.2 %, demonstrating that sintering temperature plays a significant role in densification. Additionally, fiber-reinforced composites exhibited relative densities of 90.5 % (short fiber) and 85.1% (long fiber). Microstructural observations using optical microscopy revealed that higher sintering temperatures reduced both the number and size of open pores, contributing to enhanced mechanical properties. Vickers hardness testing confirmed this trend, with bulk tungsten sintered at 1300°C achieving the highest hardness of 538 Hv. Furthermore, long fiber-reinforced composites exhibited a higher hardness of 543 Hv compared to short fiber composites, which recorded below 200 Hv. This difference is attributed to the aligned fiber structure in the long fiber composites, which promotes a more stable matrix-particle bonding compared to the random distribution in short fiber composites. These findings show that it is essential for optimizing the manufacturing process of tungsten fiber reinforced composites and securing productivity.

  • Damping Properties of Magnesium Alloy-S45 Composites with Varying Diameter of Specimen

    by Kwangmo Park, Kenjiro Sugio, Gen Sasaki

    With the advancement of equipment and machinery in industrial activities, vibrations generated during operation can adversely affect machine performance. Therefore, in this study, a magnesium alloy was selected as a vibration damping material. A magnesium alloy containing 5 wt.% zinc was produced to enhance corrosion resistance and strength. Carbon steel (S45) was employed in the fabrication of magnesium alloy-based composites. For the optimization of the damping composite, holes with diameters of Ø6 and Ø8 mm were made in the center of the S45 cylindrical rods. The damping properties of the composites were evaluated by measuring the loss factor. Among the composites, the Ø6 specimen exhibited a significantly higher loss factor compared to the Ø8 specimen. This enhanced damping performance of the Ø6 composite is attributed to improved capillary pressure during the manufacturing process, which led to better infiltration, stronger interfacial bonding, and more effective energy dissipation mechanisms. At the contact interface of the Ø6 composite, intermetallic compounds such as MgZn 2 , Mg 4 Zn 7 , and Fe 3 Mg 7 Zn 3 were observed. These compounds promote energy dissipation through mechanisms such as interfacial slip and microcrack arrest, thereby improving the loss factor.

  • Microstructural Evolution and Coupling Behavior of Dynamic Softening and Phase Transformation in TC18 Alloy during Hot Compression

    by Kaiyao Wang, Gen Sasaki, Kenjiro Sugio, Ying Guo

    This study investigates the hot deformation behavior of a near-β TC18 titanium alloy at 750 °C, with a focus on the interplay between dynamic softening mechanisms and α/β phase transformation. Compression tests were conducted at varying strain rates (0.01–1 s -1 ) and true strains (40% to 80%). The results show that increasing strain rate and deformation promote dislocation accumulation, which leads to enhanced stored energy. This drives a transform from dynamic recovery (DRV) to dynamic recrystallization (DRX) as the dominant softening mechanism and concurrently accelerates dynamic phase transformation. Meanwhile, intensified α-phase spheroidization is also observed.The strong coupling between DRX and phase transformation contributes to microstructural refinement, ultimately improving mechanical properties by balancing strength and ductility. These findings provide new insights into deformation mechanisms and offer guidance for optimizing thermomechanical processing of near-β titanium alloys.

  • Interfacial Thermal Resistance of Al-TiB2 Particle Dispersed Composites with Different Sintering Conditions

    by Kenjiro Sugio, Haruki Matsuura, Gen Sasaki

    In composite materials, interfacial thermal resistance (ITR) occurs between the matrix and the reinforcement, which is thought to deteriorate effective thermal conductivity (ETC). However, measurement of ITR is difficult, and few measurements have been reported. In this study, the ITR between Al and TiB 2 was evaluated by comparing the ETC calculated by image-based thermal conduction simulation using microstructure images with the measured ETC. Al-TiB 2 composites were prepared under different sintering conditions and the relationship between sintering conditions and ITR was investigated. Three different volume fractions of TiB 2 , three different sintering conditions, a total of nine different samples were fabricated with spark plasma sintering (SPS). The Relative density (RD) and ETC of samples with longer holding time is relatively higher than those of samples with shorter holding time, and the ITR at the Al-TiB 2 interface decreased in the samples with longer holding time. The samples pressurized after reaching the holding temperature had relatively higher RD, ETC, and ITR at the Al-TiB 2 decreased in the samples pressurized after reaching the holding temperature.

  • Influence of SiCp Addition on the Microstructure, Ageing Response and Mechanical Properties of Aluminum Matrix Composites

    by Lin Zeng, Kenjiro Sugio, Gen Sasaki

    In this study, monolithic samples and 3% SiCp/6061 composite samples were fabricated using spark plasma sintering. A comparative analysis of the microstructure, ageing response, and mechanical properties of these materials revealed that the addition of SiCp induced thermal mismatch dislocations, which accelerated the ageing kinetics. As a result, the time required to reach peak ageing decreased from 8.5 hours to 8 hours, and the peak ageing hardness increased from 102.7 HV to 113.5 HV. The tensile strength of the peak-aged composite sample improved from 315.5 MPa to 352.4 MPa, while the elongation decreased from 11.8% to 8.8%. These findings provide valuable insights for optimizing the properties of the composite, ultimately enhancing its performance and applicability in demanding engineering applications.

  • Process Optimization of Al-Mg-Si Alloy Extrusions via Machine Learning and Inverse Design

    by Yoshikazu Hayashi, Kenjiro Sugio, Gen Sasaki, Masahiko Shioi, Masato Okuno


  • Sintering Process Analysis of Aluminum Matrix Composites Using Machine Learning

    by Kenjiro Sugio, Yuuki Shinohara, Yoshikazu Hayashi, Gen Sasaki

    The sintering behavior of spark plasma sintering was analyzed by extracting features from process data obtained during the fabrication of aluminum matrix composites and machine learning using the obtained features were performed to predict relative density of composites. Seventy-five samples were sintered with different types of reinforcement, and different temperature and pressure conditions. Regression methods include linear regression such as Ridge, Lasso and Elastic Net, and nonlinear regression such as random forest, gradient boosting and XGBoost were tested. XGBoost had the highest prediction accuracy and the trained model was used for Shapley additive explanations value analysis and inverse analysis.