Hao-Chung Kuo
Research Subjects
Hao-Chung Kuo has a total of 91 co-authors. Here are the top co-authors by number of shared publications:
- Tien-Chang Lu
National yang Ming Chiao Tung University
14 shared publications S. C. Wang
National Chiao Tung Univ. (Taiwan)
10 shared publicationsC. H. Chiu
Advanced Optoelectronic Technology Inc
3 shared publicationsM. H. Lo
National Chiao Tung Univ. (Taiwan)
3 shared publicationsS.C. Wang
3 shared publicationsC. E. Lee
Department of Photonics and Institute of Electro-Optical Engineering, National Chiao Tung University, Hsinchu 300, Taiwan
2 shared publications
Latest Publications
- 1 June 2018
- Published by Wolters Kluwer Health in Pediatric Critical Care Medicine
- Vol. 19 (6S) , 264-265
Abstract PCCLB-67: The Strategies of Left ventricle Decompression in Pediatric Peripheral Extracorporeal Membrane Oxygenation
- 1 June 2018
- Published by Wolters Kluwer Health in Pediatric Critical Care Medicine
- Vol. 19 (6S) , 264-265
Abstract PCCLB-67: The Strategies of Left ventricle Decompression in Pediatric Peripheral Extracorporeal Membrane Oxygenation
- 1 July 2014
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 4 (57) , 30392-30397
Waveguide based energy transfer with gold nanoclusters for detection of hydrogen peroxide
Detection of hydrogen peroxide by using fluorescence resonance energy transfer from InGaN quantum wells to Au nanoclusters via optical waveguiding has been demonstrated. This technique provides a new strategy for the visual detection of H2O2 with large-area analysis.
- 1 July 2014
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 4 (57) , 30392-30397
Waveguide based energy transfer with gold nanoclusters for detection of hydrogen peroxide
Detection of hydrogen peroxide by using fluorescence resonance energy transfer from InGaN quantum wells to Au nanoclusters via optical waveguiding has been demonstrated. This technique provides a new strategy for the visual detection of H2O2 with large-area analysis.
- 8 September 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8123, 81231D-81231
Efficiency droop improvement in GaN-based light emitting diodes by graded-composition electron blocking layer
A graded-composition electron blocking layer (GEBL) with aluminum composition increasing along [0001] direction was designed for c-plane GaN-based light-emitting diodes (LEDs). The simulation results demonstrated that such GEBL can effectively enhance the capability of hole transportation across the EBL as well as the electron confinement. Consequently, the LED with GEBL grown by metal-organic chemical vapor deposition exhibited better electrical characteristics, and much higher output power at high current density, as compared to conventional LED. Meanwhile, the efficiency droop was reduced from 34% in conventional LED to only 4% from the maximum value at low injection current to 200 A/cm2.
- 8 September 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8123, 81231D-81231
Efficiency droop improvement in GaN-based light emitting diodes by graded-composition electron blocking layer
A graded-composition electron blocking layer (GEBL) with aluminum composition increasing along [0001] direction was designed for c-plane GaN-based light-emitting diodes (LEDs). The simulation results demonstrated that such GEBL can effectively enhance the capability of hole transportation across the EBL as well as the electron confinement. Consequently, the LED with GEBL grown by metal-organic chemical vapor deposition exhibited better electrical characteristics, and much higher output power at high current density, as compared to conventional LED. Meanwhile, the efficiency droop was reduced from 34% in conventional LED to only 4% from the maximum value at low injection current to 200 A/cm2.
- 10 February 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7954, 795408
Improvement in efficiency droop of GaN-based light-emitting diodes by optimization of active regions
We had demonstrated several novel methods to improve efficiency droop behavior in GaN-based light-emitting diodes (LEDs). LEDs with different kinds of insertion layers (ILs) between the multiple quantum wells (MQWs) layer and n-GaN layer were investigated. By using low-temperature (LT, 780°C) n-GaN as IL, the efficiency droop behavior can be alleviated from 54% in reference LED to 36% from the maximum value at low injection current to 200 mA, which is much smaller than that of 49% in LED with InGaN/GaN short-period superlattices (SPS) layer. The polarization field in MQWs is found to be smallest in LED with InGaN/GaN SPS layer. However, the V-shape defect density, about 5.3×108 cm-2, in its MQWs region is much higher than that value of 2.9×108 cm-2 in LED with LT n-GaN layer, which will lead to higher defect-related tunneling leakage of carriers. Therefore, we can mainly assign this alleviation of efficiency droop to the reduction of dislocation density in MQWs region rather than the decrease of polarization field. At second part, LEDs with graded-thickness multiple quantum wells (GQW) was designed and found to have superior hole distribution as well as radiative recombination distribution by simulation modeling. Accordingly, the experimental investigation of electroluminescence spectrum reveals additional emission from the previous narrower wells within GQWs. Consequently, the efficiency droop can be alleviated to be about 16% from maximum at current density of 30 A/cm2 to 200 A/cm2. Moreover, the light output power is enhanced by 35% at 20 A/cm2.
- 10 February 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7954, 795408
Improvement in efficiency droop of GaN-based light-emitting diodes by optimization of active regions
We had demonstrated several novel methods to improve efficiency droop behavior in GaN-based light-emitting diodes (LEDs). LEDs with different kinds of insertion layers (ILs) between the multiple quantum wells (MQWs) layer and n-GaN layer were investigated. By using low-temperature (LT, 780°C) n-GaN as IL, the efficiency droop behavior can be alleviated from 54% in reference LED to 36% from the maximum value at low injection current to 200 mA, which is much smaller than that of 49% in LED with InGaN/GaN short-period superlattices (SPS) layer. The polarization field in MQWs is found to be smallest in LED with InGaN/GaN SPS layer. However, the V-shape defect density, about 5.3×108 cm-2, in its MQWs region is much higher than that value of 2.9×108 cm-2 in LED with LT n-GaN layer, which will lead to higher defect-related tunneling leakage of carriers. Therefore, we can mainly assign this alleviation of efficiency droop to the reduction of dislocation density in MQWs region rather than the decrease of polarization field. At second part, LEDs with graded-thickness multiple quantum wells (GQW) was designed and found to have superior hole distribution as well as radiative recombination distribution by simulation modeling. Accordingly, the experimental investigation of electroluminescence spectrum reveals additional emission from the previous narrower wells within GQWs. Consequently, the efficiency droop can be alleviated to be about 16% from maximum at current density of 30 A/cm2 to 200 A/cm2. Moreover, the light output power is enhanced by 35% at 20 A/cm2.
- 7 June 2010
- Published by AIP Publishing in Applied Physics Letters
- Vol. 96 (23) , 231101
Low efficiency droop in blue-green m-plane InGaN/GaN light emitting diodes
We investigated the electroluminescence and relatively external quantum efficiency (EQE) of m-plane InGaN/GaN light emitting diodes (LEDs) emitting at 480 nm to elucidate the droop behaviors in nitride-based LEDs. With increasing the injection current density to , the m-plane LEDs exhibit only 13% efficiency droop, whereas conventional c-plane LEDs suffer from efficiency droop at very low injection current density and the EQE of c-plane LEDs decrease to as little as 50% of its maximum value. Our simulation models show that in m-plane LEDs the absence of polarization fields manifest not only the hole distribution more uniform among the wells but also the reduction in electron overflow out of electron blocking layer. These results suggest that the nonuniform distribution of holes and electron leakage current due to strong polarization fields are responsible for the relatively significant efficiency droop of conventional c-plane LEDs.- 7 June 2010
- Published by AIP Publishing in Applied Physics Letters
- Vol. 96 (23) , 231101
Low efficiency droop in blue-green m-plane InGaN/GaN light emitting diodes
We investigated the electroluminescence and relatively external quantum efficiency (EQE) of m-plane InGaN/GaN light emitting diodes (LEDs) emitting at 480 nm to elucidate the droop behaviors in nitride-based LEDs. With increasing the injection current density to , the m-plane LEDs exhibit only 13% efficiency droop, whereas conventional c-plane LEDs suffer from efficiency droop at very low injection current density and the EQE of c-plane LEDs decrease to as little as 50% of its maximum value. Our simulation models show that in m-plane LEDs the absence of polarization fields manifest not only the hole distribution more uniform among the wells but also the reduction in electron overflow out of electron blocking layer. These results suggest that the nonuniform distribution of holes and electron leakage current due to strong polarization fields are responsible for the relatively significant efficiency droop of conventional c-plane LEDs.- 22 June 2009
- Published by AIP Publishing in Applied Physics Letters
- Vol. 94 (25) , 251912
Nanorod epitaxial lateral overgrowth of a-plane GaN with low dislocation density
The crystal quality of -plane GaN films was improved by using epitaxial lateral overgrowth on a nanorod GaN template. The investigation of x-ray diffraction showed that the strain in -plane GaN grown on -plane sapphire could be mitigated. The average threading dislocation density estimated by transmission electron microscopy was reduced from to . From the temperature-dependent photoluminescence, the quantum efficiency of the -plane GaN was enhanced by the nanorod epitaxial lateral overgrowth (NRELOG). These results demonstrated the opportunity of achieving -plane GaN films with low dislocation density and high crystal quality via NRELOG.- 22 June 2009
- Published by AIP Publishing in Applied Physics Letters
- Vol. 94 (25) , 251912
Nanorod epitaxial lateral overgrowth of a-plane GaN with low dislocation density
The crystal quality of -plane GaN films was improved by using epitaxial lateral overgrowth on a nanorod GaN template. The investigation of x-ray diffraction showed that the strain in -plane GaN grown on -plane sapphire could be mitigated. The average threading dislocation density estimated by transmission electron microscopy was reduced from to . From the temperature-dependent photoluminescence, the quantum efficiency of the -plane GaN was enhanced by the nanorod epitaxial lateral overgrowth (NRELOG). These results demonstrated the opportunity of achieving -plane GaN films with low dislocation density and high crystal quality via NRELOG.- 1 January 2009
- Published by The Electrochemical Society in Electrochemical and Solid-State Letters
- Vol. 12 (2) , H44-H46
Output Power Enhancement of Vertical-Injection Ultraviolet Light-Emitting Diodes by GaN-Free and Surface Roughness Structures
Nitride-based UV, vertical-injection light-emitting diodes (VLEDs) with GaN-free and surface roughness structures operating at were proposed and demonstrated by a combination of wafer bonding and laser lift-off processes. The GaN-free structure offers a promising potential for enhancing the light output of UV-VLEDs. The light output enhancement was performed by removing the GaN. With the help of adopting a roughened surface, the light-output power of the UV-VLEDs could be further enhanced by a factor of 2.3 as compared with that of UV-VLED without a roughened surface. The total enhancement of surface-roughened GaN-free UV-VLEDs was increased by a factor of 7.8 compared to that of conventional UV-LEDs at a driving current injection of .
- 1 January 2009
- Published by The Electrochemical Society in Electrochemical and Solid-State Letters
- Vol. 12 (2) , H44-H46
Output Power Enhancement of Vertical-Injection Ultraviolet Light-Emitting Diodes by GaN-Free and Surface Roughness Structures
Nitride-based UV, vertical-injection light-emitting diodes (VLEDs) with GaN-free and surface roughness structures operating at were proposed and demonstrated by a combination of wafer bonding and laser lift-off processes. The GaN-free structure offers a promising potential for enhancing the light output of UV-VLEDs. The light output enhancement was performed by removing the GaN. With the help of adopting a roughened surface, the light-output power of the UV-VLEDs could be further enhanced by a factor of 2.3 as compared with that of UV-VLED without a roughened surface. The total enhancement of surface-roughened GaN-free UV-VLEDs was increased by a factor of 7.8 compared to that of conventional UV-LEDs at a driving current injection of .
- 13 November 2008
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7135, 71351Z
Epitaxial Lateral Overgrowth of GaN-based Light Emitting Diodes on SiO 2 Nanorod-Array Patterned Sapphire Substrates by MOCVD
High efficiency GaN-based light-emitting diodes (LEDs) are demonstrated by a nanoscale epitaxial lateral overgrowth (NELO) method on a SiO2 nanorod-array patterned sapphire substrate (NAPSS). The SiO2 NAPSS was fabricated by a self-assembled Ni nano clusters and reactive ion etching. The average diameter and density of the formed SiO2 nanorod-array was about 100 to 150 nm and 3 x 109 cm-2. The transmission electron microscopy images suggest that the voids between SiO2 nanorods and the stacking faults introduced during the NELO of GaN can effectively suppress the threading dislocation density. The output power and external quantum efficiency of the fabricated LED by NELO method on NAPSS were enhanced by 52% and 56% respectively, compared to those of a conventional LED. The improvements originated from both the enhanced light extraction assisted by the NAPSS, and the reduced dislocation densities using the NELO method.
- 13 November 2008
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7135, 71351Z
Epitaxial Lateral Overgrowth of GaN-based Light Emitting Diodes on SiO 2 Nanorod-Array Patterned Sapphire Substrates by MOCVD
High efficiency GaN-based light-emitting diodes (LEDs) are demonstrated by a nanoscale epitaxial lateral overgrowth (NELO) method on a SiO2 nanorod-array patterned sapphire substrate (NAPSS). The SiO2 NAPSS was fabricated by a self-assembled Ni nano clusters and reactive ion etching. The average diameter and density of the formed SiO2 nanorod-array was about 100 to 150 nm and 3 x 109 cm-2. The transmission electron microscopy images suggest that the voids between SiO2 nanorods and the stacking faults introduced during the NELO of GaN can effectively suppress the threading dislocation density. The output power and external quantum efficiency of the fabricated LED by NELO method on NAPSS were enhanced by 52% and 56% respectively, compared to those of a conventional LED. The improvements originated from both the enhanced light extraction assisted by the NAPSS, and the reduced dislocation densities using the NELO method.
- 1 November 2008
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 104 (9) , 093106
Optical study of a-plane InGaN/GaN multiple quantum wells with different well widths grown by metal-organic chemical vapor deposition
-plane InGaN/GaN multiple quantum wells of different widths ranging from 3 to 12 nm grown on -plane sapphire by metal-organic chemical vapor deposition were investigated. The peak emission intensity of the photoluminescence (PL) reveals a decreasing trend as the well width increases from 3 to 12 nm. Low temperature (9 K) time-resolved PL (TRPL) study shows that the sample with 3-nm-thick wells has the best optical property with a fastest exciton decay time of 0.57 ns. The results of cathodoluminescence and micro-PL scanning images for samples of different well widths further verify that the more uniform and stronger luminescence intensity distribution are observed for the samples of thinner quantum wells. In addition, more effective capturing of excitons due to larger localization energy and shorter radiative lifetime of localized excitons are observed in thinner well width samples in the temperature dependent TRPL.- 1 November 2008
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 104 (9) , 093106
Optical study of a-plane InGaN/GaN multiple quantum wells with different well widths grown by metal-organic chemical vapor deposition
-plane InGaN/GaN multiple quantum wells of different widths ranging from 3 to 12 nm grown on -plane sapphire by metal-organic chemical vapor deposition were investigated. The peak emission intensity of the photoluminescence (PL) reveals a decreasing trend as the well width increases from 3 to 12 nm. Low temperature (9 K) time-resolved PL (TRPL) study shows that the sample with 3-nm-thick wells has the best optical property with a fastest exciton decay time of 0.57 ns. The results of cathodoluminescence and micro-PL scanning images for samples of different well widths further verify that the more uniform and stronger luminescence intensity distribution are observed for the samples of thinner quantum wells. In addition, more effective capturing of excitons due to larger localization energy and shorter radiative lifetime of localized excitons are observed in thinner well width samples in the temperature dependent TRPL.- 6 October 2008
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 23 (12)
Investigation of InGaN/GaN power chip light emitting diodes with TiO2/SiO2omnidirectional reflector
- 6 October 2008
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 23 (12)
Investigation of InGaN/GaN power chip light emitting diodes with TiO2/SiO2omnidirectional reflector