Aziz Tekin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aziz Tekin has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Onur Ketenoglu
Department of Food Engineering, Faculty of Agriculture, Eskişehir Osmangazi University, Eskişehir, Turkey
6 shared publications - Cansu Ekin Gumus
Department of Food Engineering, Ankara University, Ankara, Türkiye
4 shared publications Asli Yorulmaz
Department of Food Engineering, Faculty of Engineering, Aydin Adnan Menderes University , Aydın, 09010
3 shared publicationsAslı Yorulmaz
Food Engineering Department, Faculty of Engineering Adnan Menderes University Aydın 09100 Turkey
3 shared publications- Aslı Yorulmaz
Adnan Menderes Üniversitesi
3 shared publications Behic Mert
Department of Food Engineering Faculty of Engineering, Middle East Technical University Ankara Turkey
3 shared publications
Latest Publications
- Open Access
GC-Derived Volatile Profiling of Commercial Thyme and Oregano Labeled Products and Evaluation of Portable NIR Screening
Commercial aromatic herbs sold under the names thyme and oregano may encompass heterogeneous plant materials, making chemical-profile screening important even when botanical identity is unknown. This study characterized 110 commercial products marketed in Türkiye and evaluated whether portable near-infrared (NIR) spectroscopy could predict chemical-profile classes derived independently from GC-FID/MS data. Commercial labels were recorded but were not treated as verified species identities. Essential oils were measured in technical duplicate for 23 volatile compounds; replicate means were subjected to compositional data treatment, principal component analysis and Ward clustering. Two clusters were selected by the silhouette criterion (0.485), and cluster stability under technical-replicate resampling was high (median adjusted Rand index, 0.907). Cluster 1 (n = 17) was relatively enriched in sabinene, caryophyllene, carvacrol and delta-3-carene, whereas Cluster 2 (n = 93) showed higher myrcene, p-cymene, alpha-pinene and beta-pinene. Two NIR spectra were collected per sample. To prevent replicate leakage, spectra were averaged before repeated nested cross-validation; a grouped-replicate analysis was also performed. A majority-class baseline achieved 84.55% accuracy but only 0.500 balanced accuracy. The best primary model, shrinkage linear discriminant analysis, yielded a mean accuracy of 0.689, a balanced accuracy of 0.565, a macro-F1 of 0.530 and a Matthews correlation coefficient of 0.103. The grouped-replicate sensitivity analysis gave a balanced accuracy of 0.592. Thus, GC-FID/MS revealed a stable chemical-profile structure, but portable NIR did not reliably recover the minority chemical class. NIR may support exploratory triage after broader calibration, but the present data do not support stand-alone botanical authentication or definitive chemical-class assignment.
Open AccessGC-Derived Volatile Profiling of Commercial Thyme and Oregano Labeled Products and Evaluation of Portable NIR Screening
Commercial aromatic herbs sold under the names thyme and oregano may encompass heterogeneous plant materials, making chemical-profile screening important even when botanical identity is unknown. This study characterized 110 commercial products marketed in Türkiye and evaluated whether portable near-infrared (NIR) spectroscopy could predict chemical-profile classes derived independently from GC-FID/MS data. Commercial labels were recorded but were not treated as verified species identities. Essential oils were measured in technical duplicate for 23 volatile compounds; replicate means were subjected to compositional data treatment, principal component analysis and Ward clustering. Two clusters were selected by the silhouette criterion (0.485), and cluster stability under technical-replicate resampling was high (median adjusted Rand index, 0.907). Cluster 1 (n = 17) was relatively enriched in sabinene, caryophyllene, carvacrol and delta-3-carene, whereas Cluster 2 (n = 93) showed higher myrcene, p-cymene, alpha-pinene and beta-pinene. Two NIR spectra were collected per sample. To prevent replicate leakage, spectra were averaged before repeated nested cross-validation; a grouped-replicate analysis was also performed. A majority-class baseline achieved 84.55% accuracy but only 0.500 balanced accuracy. The best primary model, shrinkage linear discriminant analysis, yielded a mean accuracy of 0.689, a balanced accuracy of 0.565, a macro-F1 of 0.530 and a Matthews correlation coefficient of 0.103. The grouped-replicate sensitivity analysis gave a balanced accuracy of 0.592. Thus, GC-FID/MS revealed a stable chemical-profile structure, but portable NIR did not reliably recover the minority chemical class. NIR may support exploratory triage after broader calibration, but the present data do not support stand-alone botanical authentication or definitive chemical-class assignment.
- 4 February 2026
- Published by Taylor & Francis in Food Additives & Contaminants: Part A
- Vol. 43 (4) , 537-544
Changes in 3-chloro-1,2-propanediol and glycidyl esters content during post-bleaching of palm olein
Refined, bleached and deodorised (RBD) palm olein imported after long shipment may require post-bleaching and deodorisation to restore quality. In this study, an RBD palm olein imported from an overseas country was bleached using a range of bleaching earths (BEs) to determine their effects on the content of 3-chloro-1,2-propanediol esters (3-MCPDE) and glycidyl esters (GE), and on some quality parameters such as peroxide value (PV), colour, conjugated diene and trienes. Four types of bleaching earths (Tonsil® A, B, C and D) were used at 0.5-3.0% (w/w). Tonsil® A and B were acid-activated, Tonsil® C was an acidic earth while Tonsil® D was a neutral one. The results showed that the highest reductions in PV and GE contents were achieved by acid-activated BEs (Tonsil® A and B) used at 3.0% (w/w). On the other hand, 3-MCPDE content was not significantly affected by the BE type and ratio although some reductions were detected using neutral earth. Conjugated triene and L* values increased with the increase of the earth ratio while some decreases were observed in the redness, b* and conjugated diene values.
- 4 February 2026
- Published by Taylor & Francis in Food Additives & Contaminants: Part A
- Vol. 43 (4) , 537-544
Changes in 3-chloro-1,2-propanediol and glycidyl esters content during post-bleaching of palm olein
Refined, bleached and deodorised (RBD) palm olein imported after long shipment may require post-bleaching and deodorisation to restore quality. In this study, an RBD palm olein imported from an overseas country was bleached using a range of bleaching earths (BEs) to determine their effects on the content of 3-chloro-1,2-propanediol esters (3-MCPDE) and glycidyl esters (GE), and on some quality parameters such as peroxide value (PV), colour, conjugated diene and trienes. Four types of bleaching earths (Tonsil® A, B, C and D) were used at 0.5-3.0% (w/w). Tonsil® A and B were acid-activated, Tonsil® C was an acidic earth while Tonsil® D was a neutral one. The results showed that the highest reductions in PV and GE contents were achieved by acid-activated BEs (Tonsil® A and B) used at 3.0% (w/w). On the other hand, 3-MCPDE content was not significantly affected by the BE type and ratio although some reductions were detected using neutral earth. Conjugated triene and L* values increased with the increase of the earth ratio while some decreases were observed in the redness, b* and conjugated diene values.
- 20 November 2025
- Published by Elsevier in Food and Chemical Toxicology
- Vol. 207, 115858
Food emulsion characteristics influence the release and absorption of 3-chloropropane-1,2-diol esters
- 20 November 2025
- Published by Elsevier in Food and Chemical Toxicology
- Vol. 207, 115858
Food emulsion characteristics influence the release and absorption of 3-chloropropane-1,2-diol esters
- 17 November 2025
- Published by Wiley in European Journal of Lipid Science and Technology
- Vol. 128 (1)
Bleaching of Hazelnut Oil Before and After Deacidification
Hazelnut oil extracted from hazelnut fruits is refined to enhance its edible properties. Bleaching is one of the key refining steps for high‐acid oils such as hazelnut oil because they are generally subjected to physical refining. This study aimed to investigate the effects of earth type and deacidification on hazelnut oil quality during bleaching. For this purpose, degummed and deacidified hazelnut oils were subjected to bleaching using neutral and acid‐activated clays at various ratios (1.25%, 2.50%, and 3.75%). Deacidification was achieved using a molecular distillation (MD) unit, and the free fatty acid (FFA) content of degummed hazelnut oil was reduced from 12.6% to 2.24%. The MD process also effectively decreased peroxide value (PV) and tocopherol content, which were also reduced by bleaching treatments. More tocopherol loss and peroxide decomposition were also observed with acid‐activated clay during bleaching; the latter resulted in triene conjugation. Using acid‐activated earth increased stigmastadiene formation by the removal of one molecule of water from the sterols. Besides, distilled oil lost more tocopherol after this process than non‐distilled oil. Distillation did not affect color values, while bleaching earth and ratio considerably affected their reductions. Practical Applications : High‐acid oils are generally refined with physical methods such as degumming, bleaching, and distillation to reduce refining loss. Pre‐deacidification, performed by distillation, is applied to these oils before or after bleaching to reduce the free fatty acid content to less than 2%. This study examines the impact of the sequence of distillation and bleaching treatments, as well as the type of earth and ratio, on the quality of hazelnut oil. The findings indicated that the application of distillation before bleaching did not affect the color removal during bleaching; however, this method resulted in greater tocopherol losses compared to applying distillation after bleaching. Tocopherols are known to play a protective role against lipid oxidation, and therefore, their reduction is considered undesirable for maintaining oil quality.
- 17 November 2025
- Published by Wiley in European Journal of Lipid Science and Technology
- Vol. 128 (1)
Bleaching of Hazelnut Oil Before and After Deacidification
Hazelnut oil extracted from hazelnut fruits is refined to enhance its edible properties. Bleaching is one of the key refining steps for high‐acid oils such as hazelnut oil because they are generally subjected to physical refining. This study aimed to investigate the effects of earth type and deacidification on hazelnut oil quality during bleaching. For this purpose, degummed and deacidified hazelnut oils were subjected to bleaching using neutral and acid‐activated clays at various ratios (1.25%, 2.50%, and 3.75%). Deacidification was achieved using a molecular distillation (MD) unit, and the free fatty acid (FFA) content of degummed hazelnut oil was reduced from 12.6% to 2.24%. The MD process also effectively decreased peroxide value (PV) and tocopherol content, which were also reduced by bleaching treatments. More tocopherol loss and peroxide decomposition were also observed with acid‐activated clay during bleaching; the latter resulted in triene conjugation. Using acid‐activated earth increased stigmastadiene formation by the removal of one molecule of water from the sterols. Besides, distilled oil lost more tocopherol after this process than non‐distilled oil. Distillation did not affect color values, while bleaching earth and ratio considerably affected their reductions. Practical Applications : High‐acid oils are generally refined with physical methods such as degumming, bleaching, and distillation to reduce refining loss. Pre‐deacidification, performed by distillation, is applied to these oils before or after bleaching to reduce the free fatty acid content to less than 2%. This study examines the impact of the sequence of distillation and bleaching treatments, as well as the type of earth and ratio, on the quality of hazelnut oil. The findings indicated that the application of distillation before bleaching did not affect the color removal during bleaching; however, this method resulted in greater tocopherol losses compared to applying distillation after bleaching. Tocopherols are known to play a protective role against lipid oxidation, and therefore, their reduction is considered undesirable for maintaining oil quality.
- Open Access
- 23 September 2024
- Published by Oxford University Press (OUP) in International Journal of Food Science and Technology
- Vol. 59 (11) , 8172-8180
Effects of pre-deacidification on 3-MCPDE and GE contents of high-acid oils during refining
Crude fats and oils may have high free fatty acid (FFA) content depending on raw material quality and processing conditions. Their refining is always a challenge due to refining loss and the formation of some process contaminants such as 3-monochloropropane-1,2-diol esters (3-MCPDE), and glycidyl esters (GE). In this study, crude hazelnut oil having 12.10% FFA was degummed, bleached, and pre-deacidified by a molecular distillation (MD) unit before neutralisation and deodorisation. Changes in FFA, diglyceride(DG), 3-MCPDE, GE, and tocopherol contents were monitored. Almost no changes were detected in FFA and DG contents during degumming and bleaching while the latter resulted in the 3-MCPDE formation and GE reduction. Some tocopherol losses were also observed after these steps. On the other hand, a huge amount of FFA was distilled (from 12.10% to 1.71%) by the MD process performed at 200 °C, 0.25 mbar, as well as with a 53.6% loss of tocopherol. The samples were then subjected to deodorisation before (MD-PHY) and after neutralisation (MD-CHE) at 230 °C under 2 mbar absolute pressure for 2, 4, and 8 h. While some 3-MCPDE and GE formations were detected during MD-CHE, there were almost no formations in these contaminants after MD-PHY. When the bleached oil having 12.10% FFA was also directly deodorised at given conditions, no formations but some reductions in 3-MCPDE and GE contents of the oils were determined, possibly because of esterification of FFA with DGs that are an important precursor of these contaminants.
- 23 September 2024
- Published by Oxford University Press (OUP) in International Journal of Food Science and Technology
- Vol. 59 (11) , 8172-8180
Open AccessEffects of pre-deacidification on 3-MCPDE and GE contents of high-acid oils during refining
Crude fats and oils may have high free fatty acid (FFA) content depending on raw material quality and processing conditions. Their refining is always a challenge due to refining loss and the formation of some process contaminants such as 3-monochloropropane-1,2-diol esters (3-MCPDE), and glycidyl esters (GE). In this study, crude hazelnut oil having 12.10% FFA was degummed, bleached, and pre-deacidified by a molecular distillation (MD) unit before neutralisation and deodorisation. Changes in FFA, diglyceride(DG), 3-MCPDE, GE, and tocopherol contents were monitored. Almost no changes were detected in FFA and DG contents during degumming and bleaching while the latter resulted in the 3-MCPDE formation and GE reduction. Some tocopherol losses were also observed after these steps. On the other hand, a huge amount of FFA was distilled (from 12.10% to 1.71%) by the MD process performed at 200 °C, 0.25 mbar, as well as with a 53.6% loss of tocopherol. The samples were then subjected to deodorisation before (MD-PHY) and after neutralisation (MD-CHE) at 230 °C under 2 mbar absolute pressure for 2, 4, and 8 h. While some 3-MCPDE and GE formations were detected during MD-CHE, there were almost no formations in these contaminants after MD-PHY. When the bleached oil having 12.10% FFA was also directly deodorised at given conditions, no formations but some reductions in 3-MCPDE and GE contents of the oils were determined, possibly because of esterification of FFA with DGs that are an important precursor of these contaminants.
- 18 March 2022
- Published by Elsevier in Food Chemistry
- Vol. 386, 132744
Furan formation in some vegetable oils during heat treatments
- 18 March 2022
- Published by Elsevier in Food Chemistry
- Vol. 386, 132744
Furan formation in some vegetable oils during heat treatments
- 1 November 2021
- Published by Wiley in Journal of the American Oil Chemists' Society
- Vol. 99 (2) , 175-179
Separation of squalene from olive oil deodorizer distillate using short‐path molecular distillation
Squalene was recovered from an olive oil deodorizer distillate (OODD) containing 40% of squalene by a two‐step process. The first step was to esterify the free fatty acids (FFAs) to make them less volatile. The second step was to separate the squalene by molecular distillation. The best esterification conditions were found to be 190°C and 360 min, where FFA content of the reaction mixture was reduced from 49.3% to 7.9%, however, an inevitable squalene loss (30%) was also observed due to a discontinuous operation. The remaining squalene (28%) in the esterified mixture was then distilled using a molecular distillation unit at elevated temperatures (190–230°C) and pressures (0.05–5 mmHg). When the temperature and vacuum during distillation increased, FFA content in the distillate reduced while distillate yield and squalene purity increased. The highest distillate yield (27.7%) and squalene purity (98.1%) were obtained at the highest applied temperature (230°C) under the lowest absolute pressure (0.05 mmHg), where FFA content of distillate was measured as 1.8%. High percentage of squalene (95%–98%) could be distilled at 230°C between 0.05 and 0.5 mmHg absolute pressures. The overall squalene recovery after all treatments was calculated as 68%.
- 1 November 2021
- Published by Wiley in Journal of the American Oil Chemists' Society
- Vol. 99 (2) , 175-179
Separation of squalene from olive oil deodorizer distillate using short‐path molecular distillation
Squalene was recovered from an olive oil deodorizer distillate (OODD) containing 40% of squalene by a two‐step process. The first step was to esterify the free fatty acids (FFAs) to make them less volatile. The second step was to separate the squalene by molecular distillation. The best esterification conditions were found to be 190°C and 360 min, where FFA content of the reaction mixture was reduced from 49.3% to 7.9%, however, an inevitable squalene loss (30%) was also observed due to a discontinuous operation. The remaining squalene (28%) in the esterified mixture was then distilled using a molecular distillation unit at elevated temperatures (190–230°C) and pressures (0.05–5 mmHg). When the temperature and vacuum during distillation increased, FFA content in the distillate reduced while distillate yield and squalene purity increased. The highest distillate yield (27.7%) and squalene purity (98.1%) were obtained at the highest applied temperature (230°C) under the lowest absolute pressure (0.05 mmHg), where FFA content of distillate was measured as 1.8%. High percentage of squalene (95%–98%) could be distilled at 230°C between 0.05 and 0.5 mmHg absolute pressures. The overall squalene recovery after all treatments was calculated as 68%.
- 1 May 2021
- Published by Elsevier in Food Chemistry
- Vol. 345, 128856
Formation kinetics of polycyclic aromatic hydrocarbons (PAHs) during drying process of olive pomace
- 1 May 2021
- Published by Elsevier in Food Chemistry
- Vol. 345, 128856
Formation kinetics of polycyclic aromatic hydrocarbons (PAHs) during drying process of olive pomace
- 30 April 2020
- Published by Akademik Gida in Akademik Gıda
- Vol. 18 (1) , 96-104
Bitkisel Yağlarda 3-Monokloropropan-1,2-diol (3-MCPD) ve Glisidil Esterleri Oluşumu ve Azaltılması
3-Monokloropropan-1,2-diol (3-MCPD) ve glisidol, serbest veya esterleşmiş formlarda bulunabilen ısıl işlem kaynaklı gıda bulaşanlarıdır. Uluslararası Kanser Araştırma Ajansı (IARC) 3-MCPD’yi Grup 2B (insanlar için olası karsinojen) glisidolü ise Grup 2A (insanlar için muhtemel karsinojen) olarak sınıflandırmıştır. Toksisitesinden dolayı serbest 3-MCPD için maksimum tolere edilebilir günlük alım (TDI) miktarı JECFA tarafından 2 µg/kg vücut ağırlığı olarak belirlenmiştir. Ayrıca Avrupa Komisyonu’nun 2018 yılında yaptığı son düzenleme ile bitkisel yağlarda glisidil esterleri limit değeri 1 mg/kg olarak belirlenmiştir. Mono ve digliseritler ile klor iyonu gibi prekürsörlerin rafine bitkisel yağlarda 3-MCPD ve glisidil ester bulaşanlarının oluşumundan sorumlu olduğu bildirilmiştir. Bunun yanında bitkisel yağların rafinasyonu sırasında uygulanan sıcaklık ve sürenin de bu bulaşanların oluşumunu önemli ölçüde etkilediği tespit edilmiştir. Bu derlemede, ilgili güncel literatür ışığında bitkisel yağlarda 3-MCPD ve glisidil esterleri oluşumuna sebep olan faktörler ve bu bulaşanların azaltılmasında kullanılan yöntemler incelenmiştir.
- 30 April 2020
- Published by Akademik Gida in Akademik Gıda
- Vol. 18 (1) , 96-104
Bitkisel Yağlarda 3-Monokloropropan-1,2-diol (3-MCPD) ve Glisidil Esterleri Oluşumu ve Azaltılması
3-Monokloropropan-1,2-diol (3-MCPD) ve glisidol, serbest veya esterleşmiş formlarda bulunabilen ısıl işlem kaynaklı gıda bulaşanlarıdır. Uluslararası Kanser Araştırma Ajansı (IARC) 3-MCPD’yi Grup 2B (insanlar için olası karsinojen) glisidolü ise Grup 2A (insanlar için muhtemel karsinojen) olarak sınıflandırmıştır. Toksisitesinden dolayı serbest 3-MCPD için maksimum tolere edilebilir günlük alım (TDI) miktarı JECFA tarafından 2 µg/kg vücut ağırlığı olarak belirlenmiştir. Ayrıca Avrupa Komisyonu’nun 2018 yılında yaptığı son düzenleme ile bitkisel yağlarda glisidil esterleri limit değeri 1 mg/kg olarak belirlenmiştir. Mono ve digliseritler ile klor iyonu gibi prekürsörlerin rafine bitkisel yağlarda 3-MCPD ve glisidil ester bulaşanlarının oluşumundan sorumlu olduğu bildirilmiştir. Bunun yanında bitkisel yağların rafinasyonu sırasında uygulanan sıcaklık ve sürenin de bu bulaşanların oluşumunu önemli ölçüde etkilediği tespit edilmiştir. Bu derlemede, ilgili güncel literatür ışığında bitkisel yağlarda 3-MCPD ve glisidil esterleri oluşumuna sebep olan faktörler ve bu bulaşanların azaltılmasında kullanılan yöntemler incelenmiştir.
- 9 January 2020
- Published by Taylor & Francis in Food Additives & Contaminants: Part A
- Vol. 37 (3) , 401-407
Reducing polycyclic aromatic hydrocarbons (PAHs) in olive pomace oil using short-path molecular distillation
Bleached olive pomace oil (BOPO) was distilled using a short-path molecular distillation unit to determine the impacts of distillation conditions on the removal of 15 PAHs from the list of 16 EPA-priority pollutant PAHs. The removal of PAHs was achieved at elevated temperatures (110–230°C) and pressures (0.05, 0.5, 5 mbar). The oil was also deodorised at 230°C under 0.5, 1 and 5 mbar pressures to determine the effect of pressure during deodorisation on the removal of PAHs. High-performance liquid chromatography (HPLC) with fluorescence detector (HPLC-FLD) was used for quantifying PAH concentrations in oil samples. PAH concentrations in BOPO were considerably reduced after molecular distillation and both temperature increment and pressure decrease were effective for the removal of PAHs from olive pomace oil. When above 190°C, BaP could be reduced to <2 µg/kg at all pressures. Distillation at 230°C under 0.05 mbar absolute pressure reduced the sum of four PAHs (BaP, Chr, BaA, BbF) to 7 µg/kg, which meets the acceptable levels established by the European Union (10 µg/kg). Deodorisation effectiveness was increased by decreasing absolute pressure, particularly for light PAHs.
- 9 January 2020
- Published by Taylor & Francis in Food Additives & Contaminants: Part A
- Vol. 37 (3) , 401-407
Reducing polycyclic aromatic hydrocarbons (PAHs) in olive pomace oil using short-path molecular distillation
Bleached olive pomace oil (BOPO) was distilled using a short-path molecular distillation unit to determine the impacts of distillation conditions on the removal of 15 PAHs from the list of 16 EPA-priority pollutant PAHs. The removal of PAHs was achieved at elevated temperatures (110–230°C) and pressures (0.05, 0.5, 5 mbar). The oil was also deodorised at 230°C under 0.5, 1 and 5 mbar pressures to determine the effect of pressure during deodorisation on the removal of PAHs. High-performance liquid chromatography (HPLC) with fluorescence detector (HPLC-FLD) was used for quantifying PAH concentrations in oil samples. PAH concentrations in BOPO were considerably reduced after molecular distillation and both temperature increment and pressure decrease were effective for the removal of PAHs from olive pomace oil. When above 190°C, BaP could be reduced to <2 µg/kg at all pressures. Distillation at 230°C under 0.05 mbar absolute pressure reduced the sum of four PAHs (BaP, Chr, BaA, BbF) to 7 µg/kg, which meets the acceptable levels established by the European Union (10 µg/kg). Deodorisation effectiveness was increased by decreasing absolute pressure, particularly for light PAHs.