Hui Ding
Research Subjects
Research Interests
Hui Ding has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Xiaonong Meng
Simerics, Inc
2 shared publicationsYu Jiang
2 shared publicationsB Jiang
College of Mechanical Engineering, University of Shanghai for Science and Technology 516 Jun Gong Road, Shanghai, 200093, China
1 shared publication- Frank C. Visser
Flowserve, Etten-Leur, The Netherlands
1 shared publication Haiyang Gao
Simerics, Inc
1 shared publication- M. Furmanczyk
Simerics, Inc., Huntsville, AL 35801
1 shared publication
Latest Publications
- 29 September 2026
- Published by Springer Nature
- p. 423-433
Modeling of Compressor Reed Valve Using Two Way Coupled CFD and FEA Simulations
- 29 September 2026
- Published by Springer Nature
- p. 423-433
Modeling of Compressor Reed Valve Using Two Way Coupled CFD and FEA Simulations
- 1 January 2024
- Published by Springer Nature
- p. 101-113
Two Way Coupling of CFD Conjugate Heat Transfer Simulation with Solid Thermal Expansion in a Twin Screw Compressor
- 1 January 2024
- Published by Springer Nature
- p. 101-113
Two Way Coupling of CFD Conjugate Heat Transfer Simulation with Solid Thermal Expansion in a Twin Screw Compressor
- Open Access
- 1 August 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 604 (1) , 012005
CFD Modelling of Coupled Heat Transfer between Solid and Fluid in a Twin Screw Compressor
Temperature variation in a compressor is very critical for compression performance and efficiency. To accurately predict the thermal dynamic behaviour of a compressor, heat transfer between metal components and the working fluid needs to be properly evaluated in CFD simulation. Thermal expansion of solid components due to temperature increase may also cause excessive abrasion of metal parts and changing in leakage clearance. Solving conjugate heat transfer (CHT) of twin screw compressors not only needs to deal with complex moving rotor geometry, but also needs to consider huge difference of temperature propagation time scale inside different media. Typically, heat propagation is much slower in solid than in compressed gas. Therefore, it may take many compressor revolutions to reach a stable CHT solution if heat conduction inside solid and thermodynamic temperature change of compressed gas are directly coupled in a CFD simulation. The run time of simulation may become impractical. In this paper, an innovative approach solving conjugate heat transfer using the Mixed Timescale Coupling method between different media will be described in detail. This approach can address time scale difference in heat propagation. The proposed approach will be applied to a twin screw compressor. Simulation results will be compared with available test data. Effects of conjugate heat transfer will be evaluated by comparing the simulation results for the cases with and without considering conjugate heat transfer. Thermal expansion of the solid rotor will also be evaluated using predicted temperature distribution. Simulation will also demonstrate that the approaches used in the paper are robust, fast, and user friendly, and can be readily applied to industrial compressor systems.
- 1 August 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 604 (1) , 012005
Open AccessCFD Modelling of Coupled Heat Transfer between Solid and Fluid in a Twin Screw Compressor
Temperature variation in a compressor is very critical for compression performance and efficiency. To accurately predict the thermal dynamic behaviour of a compressor, heat transfer between metal components and the working fluid needs to be properly evaluated in CFD simulation. Thermal expansion of solid components due to temperature increase may also cause excessive abrasion of metal parts and changing in leakage clearance. Solving conjugate heat transfer (CHT) of twin screw compressors not only needs to deal with complex moving rotor geometry, but also needs to consider huge difference of temperature propagation time scale inside different media. Typically, heat propagation is much slower in solid than in compressed gas. Therefore, it may take many compressor revolutions to reach a stable CHT solution if heat conduction inside solid and thermodynamic temperature change of compressed gas are directly coupled in a CFD simulation. The run time of simulation may become impractical. In this paper, an innovative approach solving conjugate heat transfer using the Mixed Timescale Coupling method between different media will be described in detail. This approach can address time scale difference in heat propagation. The proposed approach will be applied to a twin screw compressor. Simulation results will be compared with available test data. Effects of conjugate heat transfer will be evaluated by comparing the simulation results for the cases with and without considering conjugate heat transfer. Thermal expansion of the solid rotor will also be evaluated using predicted temperature distribution. Simulation will also demonstrate that the approaches used in the paper are robust, fast, and user friendly, and can be readily applied to industrial compressor systems.
- Open Access
- 1 August 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 232 (1) , 012020
CFD simulation of a screw compressor with oil injection
In this paper, a full 3D transient CFD model of a twin screw compressor with oil injection will be described in detail. The Volume Of Fraction (VOF) approach was used for two phase flow of gas and liquid. The numeric method and simulation conditions will be explained. Simulation results will be presented with discussion. The cooling and sealing effects of oil injection will be evaluated by comparing the simulation results for the cases with and without oil. The imbalance of mass and energy of the compression system in simulation results will be rigorously checked to prove the methodologies used in the simulation are fully conservative and consistent. The efficiency, speed, and robustness of the proposed approach will also be demonstrated through the test case.
- 1 August 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 232 (1) , 012020
Open AccessCFD simulation of a screw compressor with oil injection
In this paper, a full 3D transient CFD model of a twin screw compressor with oil injection will be described in detail. The Volume Of Fraction (VOF) approach was used for two phase flow of gas and liquid. The numeric method and simulation conditions will be explained. Simulation results will be presented with discussion. The cooling and sealing effects of oil injection will be evaluated by comparing the simulation results for the cases with and without oil. The imbalance of mass and energy of the compression system in simulation results will be rigorously checked to prove the methodologies used in the simulation are fully conservative and consistent. The efficiency, speed, and robustness of the proposed approach will also be demonstrated through the test case.
- Open Access
- 26 November 2012
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 15 (6) , 062006
A CFD model for orbital gerotor motor
In this paper, a full 3D transient CFD model for orbital gerotor motor is described in detail. One of the key technologies to model such a fluid machine is the mesh treatment for the dynamically changing rotor fluid volume. Based on the geometry and the working mechanism of the orbital gerotor, a moving/deforming mesh algorithm was introduced and implemented in a CFD software package. The test simulations show that the proposed algorithm is accurate, robust, and efficient when applied to industrial orbital gerotor motor designs. Simulation results are presented in the paper and compared with experiment test data.
- 26 November 2012
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 15 (6) , 062006
Open AccessA CFD model for orbital gerotor motor
In this paper, a full 3D transient CFD model for orbital gerotor motor is described in detail. One of the key technologies to model such a fluid machine is the mesh treatment for the dynamically changing rotor fluid volume. Based on the geometry and the working mechanism of the orbital gerotor, a moving/deforming mesh algorithm was introduced and implemented in a CFD software package. The test simulations show that the proposed algorithm is accurate, robust, and efficient when applied to industrial orbital gerotor motor designs. Simulation results are presented in the paper and compared with experiment test data.
- 1 January 2011
- Published by ASME International in Journal of Fluids Engineering
- Vol. 133 (1) , 011101
Demonstration and Validation of a 3D CFD Simulation Tool Predicting Pump Performance and Cavitation for Industrial Applications
Due to complexities in geometry and physics, computational fluid dynamics (CFD) pump simulation has historically been very challenging and time consuming, especially for cases with cavitation. However, with the evolution and innovation of CFD technologies, pump cavitation simulation has improved significantly in recent years. In view of these developments, this paper will discuss a new generation CFD tool for pump cavitation simulation, using an axial flow water pump as a demonstration case. A novel CFD methodology and advanced cavitation model will be presented and discussed. Key components that are relevant to the improvement of accuracy and CFD simulation speed will be discussed in detail. An axial flow water pump is chosen as the test case to demonstrate and validate the capability and accuracy of the code discussed. Simulation results include pump head, hydraulic efficiency, and cavitation characteristic in terms of incipient net positive suction head for the whole pump flow passages using both multiple reference frame and transient approaches. Multiple operation conditions, from 70% to 120% of duty flow rate, have been evaluated and will be projected against experimental data. Furthermore, simulated cavitation patterns will be compared with video images recorded during the experiments.
- 1 January 2011
- Published by ASME International in Journal of Fluids Engineering
- Vol. 133 (1) , 011101
Demonstration and Validation of a 3D CFD Simulation Tool Predicting Pump Performance and Cavitation for Industrial Applications
Due to complexities in geometry and physics, computational fluid dynamics (CFD) pump simulation has historically been very challenging and time consuming, especially for cases with cavitation. However, with the evolution and innovation of CFD technologies, pump cavitation simulation has improved significantly in recent years. In view of these developments, this paper will discuss a new generation CFD tool for pump cavitation simulation, using an axial flow water pump as a demonstration case. A novel CFD methodology and advanced cavitation model will be presented and discussed. Key components that are relevant to the improvement of accuracy and CFD simulation speed will be discussed in detail. An axial flow water pump is chosen as the test case to demonstrate and validate the capability and accuracy of the code discussed. Simulation results include pump head, hydraulic efficiency, and cavitation characteristic in terms of incipient net positive suction head for the whole pump flow passages using both multiple reference frame and transient approaches. Multiple operation conditions, from 70% to 120% of duty flow rate, have been evaluated and will be projected against experimental data. Furthermore, simulated cavitation patterns will be compared with video images recorded during the experiments.