Yukiharu Uraoka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Yukiharu Uraoka has a total of 100 co-authors. Here are the top co-authors by number of shared publications:
- Yasuaki Ishikawa
College of Science and Engineering, Aoyama Gakuin University, Sagamihara, Kanagawa 252-5258, Japan
14 shared publications - Ichiro Yamashita
Graduate School of Materials Science, Nara Institute of Science and Technology, 8916-5 Takayama, Ikoma, Nara 6300101, Japan
8 shared publications - Masahiro Horita
Information Device Science Laboratory, Graduate School of Materials Science, Nara Institute of Science and Technology, Nara, Japan
8 shared publications - Mami N. Fujii
Division of Materials Science, Nara Institute of Science and Technology, Ikoma, Nara, JAPAN
4 shared publications - Mutsunori Uenuma
National Institute of Advanced Industrial Science and Technology (AIST) 3 , 841-0052 Saga
4 shared publications Bin Zheng
Graduate School of Materials Science, Nara Institute of Science and Technology, Ikoma, Nara 630-0192, Japan
3 shared publications
Latest Publications
- Open Access
Isotropic TFT Characteristics in the {100}-Oriented Grain-Boundary-Free Laser-Crystallized Si Thin Films
Isotropic TFT characteristics are realized in the {100}-oriented grain-boundary-free 60 nm thick Si film obtained by the continuous-wave laser lateral crystallization, where the grain- and sub-boundaries are defined as the crystallographic boundaries having misfit angles of θ > 15° and θ < 15°, respectively. Sub-boundaries are observed in the film parallel to the scan directions; the misfit angles were 5–10° and the sub-boundary density was 0.02956 μm−1. Sub-grains, joined by the sub-boundaries, have widths of 8 ~ 69 μm. The cumulative distributions of mobility, threshold voltage, and subthreshold swing agree well between the parallel and perpendicular TFTs in the film, where parallel or perpendicular means the source-to-drain directions to the laser scan direction. The maximum mobilities of the parallel and perpendicular TFTs are 695 and 663 cm2/Vs, respectively. The trap-state density NT in the sub-boundaries estimated from the product of the bond efficiency η and the dangling bond density decreases by two decades from those of the grain boundaries. A new carrier transport model of the current flow across the sub-boundary is proposed instead of the thermionic emission model for the grain boundaries.
Open AccessIsotropic TFT Characteristics in the {100}-Oriented Grain-Boundary-Free Laser-Crystallized Si Thin Films
Isotropic TFT characteristics are realized in the {100}-oriented grain-boundary-free 60 nm thick Si film obtained by the continuous-wave laser lateral crystallization, where the grain- and sub-boundaries are defined as the crystallographic boundaries having misfit angles of θ > 15° and θ < 15°, respectively. Sub-boundaries are observed in the film parallel to the scan directions; the misfit angles were 5–10° and the sub-boundary density was 0.02956 μm−1. Sub-grains, joined by the sub-boundaries, have widths of 8 ~ 69 μm. The cumulative distributions of mobility, threshold voltage, and subthreshold swing agree well between the parallel and perpendicular TFTs in the film, where parallel or perpendicular means the source-to-drain directions to the laser scan direction. The maximum mobilities of the parallel and perpendicular TFTs are 695 and 663 cm2/Vs, respectively. The trap-state density NT in the sub-boundaries estimated from the product of the bond efficiency η and the dangling bond density decreases by two decades from those of the grain boundaries. A new carrier transport model of the current flow across the sub-boundary is proposed instead of the thermionic emission model for the grain boundaries.
- Open Access
Unseeded Crystal Growth of (100)-Oriented Grain-Boundary-Free Si Thin-Film by a Single Scan of the CW-Laser Lateral Crystallization of a-Si on Insulator
Laser crystallization of a-Si film on insulating substrate is a promising technology to fabricate three-dimensional integrations (3D ICs), flat panel displays (FPDs), or flexible electronics, because the crystallization can be performed on room temperature substrate to avoid damage to the underlying devices or supporting plane. Orientation-controlled grain-boundary-free films are required to improve the uniformity in electrical characteristics of field-effect-transistors (FETs)fabricated in those films. This paper describes the recently found simple method to obtain {100}-oriented grain-boundary-free Si thin-films stably, by using a single scan of continuous-wave (CW)-laser lateral crystallization of a-Si with a highly top-flat line beam with 532 nm wavelength at room temperature in air. It was difficult to control crystal orientations in the grain-boundary-free film crystallized by the artificial modulation of solid-liquid interface, and any other trial to obtain preferential surface orientation with multiple irradiations resulted in grain boundaries. The self-organized growth of the {100}-oriented grain-boundary-free films were realized by satisfying the following conditions: (1) highly uniform top-flat line beam, (2) SiO2 cap, (3) low laser power density in the vicinity of the lateral growth threshold, and (4) single scan crystallization. Higher scan velocity makes the process window wide for the {100}-oriented grain-boundary-free film. This crystallization is very simple, because it is performed by a single unseeded scan with a line beam at room temperature substrate in air.
Open AccessUnseeded Crystal Growth of (100)-Oriented Grain-Boundary-Free Si Thin-Film by a Single Scan of the CW-Laser Lateral Crystallization of a-Si on Insulator
Laser crystallization of a-Si film on insulating substrate is a promising technology to fabricate three-dimensional integrations (3D ICs), flat panel displays (FPDs), or flexible electronics, because the crystallization can be performed on room temperature substrate to avoid damage to the underlying devices or supporting plane. Orientation-controlled grain-boundary-free films are required to improve the uniformity in electrical characteristics of field-effect-transistors (FETs)fabricated in those films. This paper describes the recently found simple method to obtain {100}-oriented grain-boundary-free Si thin-films stably, by using a single scan of continuous-wave (CW)-laser lateral crystallization of a-Si with a highly top-flat line beam with 532 nm wavelength at room temperature in air. It was difficult to control crystal orientations in the grain-boundary-free film crystallized by the artificial modulation of solid-liquid interface, and any other trial to obtain preferential surface orientation with multiple irradiations resulted in grain boundaries. The self-organized growth of the {100}-oriented grain-boundary-free films were realized by satisfying the following conditions: (1) highly uniform top-flat line beam, (2) SiO2 cap, (3) low laser power density in the vicinity of the lateral growth threshold, and (4) single scan crystallization. Higher scan velocity makes the process window wide for the {100}-oriented grain-boundary-free film. This crystallization is very simple, because it is performed by a single unseeded scan with a line beam at room temperature substrate in air.
- 9 May 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58  (9) , 090502
Degradation phenomenon in metal-oxide-semiconductor thin-film transistors and techniques for its reliability evaluation and suppression
Thin-film transistors (TFTs) using metal oxide semiconductors are very promising as driving elements of next-generation displays, and their development is rapidly progressing. However, compared to conventional Si TFTs, they exhibit numerous problems with reliability. In this paper, we outline the observations of various degradation phenomena against electrical bias stress under DC and AC voltage, discuss the degradation mechanism, introduce gate insulation film and protective film which contribute to the improvement of reliability, and propose a reliability evaluation technique using an IR microscope.
- 9 May 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58  (9) , 090502
Degradation phenomenon in metal-oxide-semiconductor thin-film transistors and techniques for its reliability evaluation and suppression
Thin-film transistors (TFTs) using metal oxide semiconductors are very promising as driving elements of next-generation displays, and their development is rapidly progressing. However, compared to conventional Si TFTs, they exhibit numerous problems with reliability. In this paper, we outline the observations of various degradation phenomena against electrical bias stress under DC and AC voltage, discuss the degradation mechanism, introduce gate insulation film and protective film which contribute to the improvement of reliability, and propose a reliability evaluation technique using an IR microscope.
- Open Access
- 29 August 2017
- Published by Springer Nature in Discover Nano
- Vol. 12  (1) , 1-12
Effect of Gold Nanoparticle Distribution in TiO2 on the Optical and Electrical Characteristics of Dye-Sensitized Solar Cells
Photoanodes comprising Au nanoparticles (GNPs) and thin TiO2 layers with a stacked structure were fabricated by repeating the application of TiO2 paste and
- 29 August 2017
- Published by Springer Nature in Discover Nano
- Vol. 12  (1) , 1-12
Open AccessEffect of Gold Nanoparticle Distribution in TiO2 on the Optical and Electrical Characteristics of Dye-Sensitized Solar Cells
Photoanodes comprising Au nanoparticles (GNPs) and thin TiO2 layers with a stacked structure were fabricated by repeating the application of TiO2 paste and
- Open Access
- 17 June 2017
- Published by Springer Nature in Discover Nano
- Vol. 12  (1) , 419
Fabrication of Nanoshell-Based 3D Periodic Structures by Templating Process using Solution-derived ZnO
Fabrication methods for a 3D periodic nanostructure with excellent and unique properties for various applications, such as photonic and phononic crystals, have attracted considerable interest. Templating processes using colloidal crystals have been proposed to create nanoshell-based 3D structures over a large area with ease. However, there are technical limitations in structural design, resulting in difficulties for structural flexibility. Here, we demonstrate a combination of proximity field nanopatterning and infiltration processes using solution-derived ZnO for a nanoshell-based 3D periodic structure with high structural flexibility and controllability. A unique process of infiltration of a solution-derived material into a polymeric template prepared by a proximity field nanopatterning process achieves the fabrication of a pre-formed layer that works as a protective layer for the template and framework for the inverse structure. Subsequently, this process shows the controllability of nanoshell thickness and significant improvement in the structure height shrinkage factor (16%) compared to those of a previous non-vacuum infiltration method (34%). The proposed method offers high controllability and flexibility in the design of structural sizes, leading to further development toward nanoshell-based 3D structures for various applications including energy devices and sensors.
- 17 June 2017
- Published by Springer Nature in Discover Nano
- Vol. 12  (1) , 419
Open AccessFabrication of Nanoshell-Based 3D Periodic Structures by Templating Process using Solution-derived ZnO
Fabrication methods for a 3D periodic nanostructure with excellent and unique properties for various applications, such as photonic and phononic crystals, have attracted considerable interest. Templating processes using colloidal crystals have been proposed to create nanoshell-based 3D structures over a large area with ease. However, there are technical limitations in structural design, resulting in difficulties for structural flexibility. Here, we demonstrate a combination of proximity field nanopatterning and infiltration processes using solution-derived ZnO for a nanoshell-based 3D periodic structure with high structural flexibility and controllability. A unique process of infiltration of a solution-derived material into a polymeric template prepared by a proximity field nanopatterning process achieves the fabrication of a pre-formed layer that works as a protective layer for the template and framework for the inverse structure. Subsequently, this process shows the controllability of nanoshell thickness and significant improvement in the structure height shrinkage factor (16%) compared to those of a previous non-vacuum infiltration method (34%). The proposed method offers high controllability and flexibility in the design of structural sizes, leading to further development toward nanoshell-based 3D structures for various applications including energy devices and sensors.
- 18 September 2016
- Published by Springer Nature
- p. 119-143
Biotemplates and Their Application to Electronic Devices
- 18 September 2016
- Published by Springer Nature
- p. 119-143
Biotemplates and Their Application to Electronic Devices
- 9 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Display Technology
- Vol. 12  (3) , 263-267
Reliability Improvement of Amorphous InGaZnO Thin-Film Transistors by Less Hydroxyl-Groups Siloxane Passivation
Amorphous indium gallium zinc oxide thin-film transistors have attracted growing interest due to its low energy consumption, possibility of low temperature fabrication and transparency. However, it still has technological problems on reliability and hump due to hydrogen related materials. To solve these problems, we made siloxane passivation layer with less OH bond using spin coating technique and carried out the bias stress testing. TFTs passivated by less OH siloxane show excellent reliability compared with high OH bond condition which showed large hump effect on each tests of positive bias stress and negative bias stress. We achieved the stable device using an organic-inorganic hybrid material by controlling OH bond, and we found that the amount of OH in the passivation layer is a key issue in oxide TFTs reliability.
- 9 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Display Technology
- Vol. 12  (3) , 263-267
Reliability Improvement of Amorphous InGaZnO Thin-Film Transistors by Less Hydroxyl-Groups Siloxane Passivation
Amorphous indium gallium zinc oxide thin-film transistors have attracted growing interest due to its low energy consumption, possibility of low temperature fabrication and transparency. However, it still has technological problems on reliability and hump due to hydrogen related materials. To solve these problems, we made siloxane passivation layer with less OH bond using spin coating technique and carried out the bias stress testing. TFTs passivated by less OH siloxane show excellent reliability compared with high OH bond condition which showed large hump effect on each tests of positive bias stress and negative bias stress. We achieved the stable device using an organic-inorganic hybrid material by controlling OH bond, and we found that the amount of OH in the passivation layer is a key issue in oxide TFTs reliability.
- Open Access
- 5 December 2014
- Published by Springer Nature in Discover Nano
- Vol. 9  (1) , 659
Silica-sol-based spin-coating barrier layer against phosphorous diffusion for crystalline silicon solar cells
The phosphorus barrier layers at the doping procedure of silicon wafers were fabricated using a spin-coating method with a mixture of silica-sol and tetramethylammonium hydroxide, which can be formed at the rear surface prior to the front phosphorus spin-on-demand (SOD) diffusion and directly annealed simultaneously with the front phosphorus layer. The optimization of coating thickness was obtained by changing the applied spin-coating speed; from 2,000 to 8,000 rpm. The CZ-Si p-type silicon solar cells were fabricated with/without using the rear silica-sol layer after taking the sheet resistance measurements, SIMS analysis, and SEM measurements of the silica-sol material evaluations into consideration. For the fabrication of solar cells, a spin-coating phosphorus source was used to form the n+ emitter and was then diffused at 930°C for 35 min. The out-gas diffusion of phosphorus could be completely prevented by spin-coated silica-sol film placed on the rear side of the wafers coated prior to the diffusion process. A roughly 2% improvement in the conversion efficiency was observed when silica-sol was utilized during the phosphorus diffusion step. These results can suggest that the silica-sol material can be an attractive candidate for low-cost and easily applicable spin-coating barrier for any masking purpose involving phosphorus diffusion.
- 5 December 2014
- Published by Springer Nature in Discover Nano
- Vol. 9  (1) , 659
Open AccessSilica-sol-based spin-coating barrier layer against phosphorous diffusion for crystalline silicon solar cells
The phosphorus barrier layers at the doping procedure of silicon wafers were fabricated using a spin-coating method with a mixture of silica-sol and tetramethylammonium hydroxide, which can be formed at the rear surface prior to the front phosphorus spin-on-demand (SOD) diffusion and directly annealed simultaneously with the front phosphorus layer. The optimization of coating thickness was obtained by changing the applied spin-coating speed; from 2,000 to 8,000 rpm. The CZ-Si p-type silicon solar cells were fabricated with/without using the rear silica-sol layer after taking the sheet resistance measurements, SIMS analysis, and SEM measurements of the silica-sol material evaluations into consideration. For the fabrication of solar cells, a spin-coating phosphorus source was used to form the n+ emitter and was then diffused at 930°C for 35 min. The out-gas diffusion of phosphorus could be completely prevented by spin-coated silica-sol film placed on the rear side of the wafers coated prior to the diffusion process. A roughly 2% improvement in the conversion efficiency was observed when silica-sol was utilized during the phosphorus diffusion step. These results can suggest that the silica-sol material can be an attractive candidate for low-cost and easily applicable spin-coating barrier for any masking purpose involving phosphorus diffusion.
- 24 November 2014
- Published by IOP Publishing in Materials Research Express
- Vol. 1  (4) , 45410
A distance-controlled nanoparticle array using PEGylated ferritin
- 24 November 2014
- Published by IOP Publishing in Materials Research Express
- Vol. 1  (4) , 45410
A distance-controlled nanoparticle array using PEGylated ferritin
- 17 July 2014
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 3  (9) , Q3050-Q3053
Vapor-Induced Improvements in Field Effect Mobility of Transparent a-IGZO TFTs
We found that high pressure assisted annealing with water vapor (HPV) is effective for improving the field effect mobility of amorphous indium-gallium-zinc oxide (a-IGZO) thin film transistors (TFTs). The HPV-annealed TFTs exhibited better performance in field effect mobility compared with dry annealing under atmospheric pressure. Secondary ion mass spectroscopy (SIMS) analysis revealed that the hydrogen content increased through the whole a-IGZO film, despite the oxygen content increasing only within 20 nm depth from the a-IGZO surface. Consequently, hydrogen can affect front channel components and improve the field effect mobility of TFTs.
- 17 July 2014
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 3  (9) , Q3050-Q3053
Vapor-Induced Improvements in Field Effect Mobility of Transparent a-IGZO TFTs
We found that high pressure assisted annealing with water vapor (HPV) is effective for improving the field effect mobility of amorphous indium-gallium-zinc oxide (a-IGZO) thin film transistors (TFTs). The HPV-annealed TFTs exhibited better performance in field effect mobility compared with dry annealing under atmospheric pressure. Secondary ion mass spectroscopy (SIMS) analysis revealed that the hydrogen content increased through the whole a-IGZO film, despite the oxygen content increasing only within 20 nm depth from the a-IGZO surface. Consequently, hydrogen can affect front channel components and improve the field effect mobility of TFTs.