TNTarun R. Naik

Tarun R. Naik

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Tarun R. Naik has a total of 13 co-authors. Here are the top co-authors by number of shared publications:

  • Rudolph N. Kraus

    Former Assistant Director, UWM Center for By-Products Utilization Univ. of Wisconsin-Milwaukee, P.O. Box 784, Milwaukee, WI 53201

    6 shared publications
  • Yoon-Moon Chun

    FACI, Professor of Structural Engineering, and Academic Program Director, Center for By-Products Utilization, Univ. of Wisconsin–Milwaukee, P.O. Box 784, Milwaukee, WI 53201

    4 shared publications
  • Bruce W. Ramme

    Senior Environmental Consultant, We Energies, 333 W. Everett St., Milwaukee, WI 53203

    2 shared publications
  • Rakesh Kumar

    Research Professor and Academic Program Director, Univ. of Wisconsin–Milwaukee Center for By-Products Utilization, PO Box 784, Milwaukee, WI 53211

    2 shared publications
  • Bruce W. Ramme

    Vice President-Environmental, We Energies, 333 West Everett Street, Milwaukee, WI 53203

    1 shared publication
  • Fethullah Canpolat

    Assistant Professor, Yildiz Technical Univ., Civil Engineering Faculty, Dept. of Civil Engineering, Davutpasa Campus, Esenler/Istanbul, Turkey 34220

    1 shared publication

Latest Publications

  • Open Access

    Compressive Strength and Leaching Behavior of Mortars with Biomass Ash

    by Gabriele Fava, Tarun R. Naik, Mattia Pierpaoli

    This study investigated the use of a biomass ash produced by a fuel combination made with wood, corn stover, and corn cob as cement replacement for the production of mortar. Biomasses are now widely accepted as a substitute for conventional fuels and are becoming essential for cost-effective production of energy. This study aimed to provide an opportunity for the annual agricultural corn-crop residue, corn stover and cob, which is increasingly being used as fuel for its valuable energy content. Measurements of workability, compressive strength, and leachate properties (pH, salinity, heavy metals and calcium ion release) of mortar specimen, at different cement substitution levels and ages, were evaluated. The results obtained reveal definitive possibilities for such mixed biomass ash to be used in cement-based materials, such as mortars. Moreover, a multiple regression analysis has been reported between the mass of calcium ions leached and the mixture composition with the compressive strength. Data show that further confirmation, on a longer span of time and of other types of mechanical properties and environmental tests, would be necessary to fully implement the use of such biomass ashes in various types of cement-based construction materials, in order to divert them from landfill disposal.


  • Effects of Fly Ash and Foundry Sand on Performance of Architectural Precast Concrete

    by Tarun R. Naik, Rudolph N. Kraus, Bruce W. Ramme, Fethullah Canpolat

    This research was conducted to establish the effects of fly ash and used foundry sand on strength and durability of concrete. Two series (Series 1 and Series 2) of experiments were performed. All concrete mixtures were produced for and at the production plant of an architectural precast concrete products producer. Concrete mixtures produced were used in manufacture of precast concrete panels. Tests were performed with normal and air-entrained fly ash concrete. Concrete test specimens were evaluated for compressive strength, abrasion resistance, salt-scaling resistance, freezing and thawing resistance, and chloride-ion penetration resistance. On the basis of strength and durability evaluations, it was concluded that both nonair and air-entrained concrete mixtures developed in this investigation are appropriate for manufacture of high-quality, high-durability architectural precast concrete using used foundry sand and fly ash.


  • Influence of Types of Coarse Aggregates on the Coefficient of Thermal Expansion of Concrete

    by Tarun R. Naik, Rudolph N. Kraus, Rakesh Kumar

    The coefficient of thermal expansion (CTE) was determined for a typical concrete-paving mixture made with six different types of coarse aggregates belonging to the basic class of glacial gravel, quartzite, granite, diabase, basalt, and dolomite. The CTE, compressive strength, and splitting tensile strength of fifteen different concrete mixtures were determined at the age of 28 days. Two parameters, CTE and splitting tensile strength, are the basic input in AASHTO’s new mechanistic-empirical pavement design method. The study revealed a noticeable variation in the values of the CTE of concrete with different types of aggregates. Concrete with quartzite aggregate had the highest value of the CTE followed by dolomite, glacial gravel, granite, and diabase or basalt. The estimated value of the splitting tensile strength of concrete, considering its compressive strength and using AASHTO’s Mechanistic-Empirical Pavement Design Guide for Level 2 design of concrete pavements was discovered to be significantly lower...


  • Monitoring System to Provide Assurance for Maintenance of Structures

    by Giacomo Moriconi, Tarun R. Naik

    Repair costs of reinforced concrete structures exponentially grow with the time from construction to the onset of corrosion and deterioration, up to inspection, evaluation, repair, and rehabilitation. Therefore, the planning of an automated-monitoring system, which is able to reveal the corrosion risk of steel reinforcement and other embedded items in concrete structures would be a critically important issue. If concrete structures such as a highway bridge are ignored from regularly planned structural condition surveys, inspections, and evaluations then it could lead to catastrophic failure and loss of life and commerce. Such failures of structures also may lead to significant financial liability. The corrosion potential of steel, whose change could indicate the onset of conditions favorable for corrosion initiation, can be monitored by embedding electrodes in the structure, either for measuring the start of corrosion or simply as a baseline reference for future inspection and evaluation. Judiciously selected suitable locations of these embedded electrodes depend on the type and geometry of the structure, as well as on the exposure condition of each of its critical structural elements. A computerized system has been in use in Italy for few years. The applications described here are for concrete structures, including one steel structure that is exposed to the sea-breeze on the Adriatic Coast of the City of Ancona, Marche, Italy. The system monitors and documents by means of the embedded electrodes and sends the records to a computer via a communication line data points both for the structure and the weather. The collected data on the computer are saved on backup files, analyzed, and finally sent via modem to a monitoring station for further processing and dissemination to the architect, engineer, and owner. This structural monitoring procedure has been applied to several concrete structures that are continuously controlled and managed from the monitoring station. These experiences show the effectiveness of the continuously monitored computer system for inspections and evaluations, as well as for scheduling repairs and rehabilitations. It is important to evaluate the installation of such a structural monitoring system on any infrastructure to minimize the impact of its disruption on public safety, daily commerce, future liability, and maintenance.


  • Top Cited Papers

    Sustainability of Concrete Construction

    by Tarun R. Naik

    Sustainability is important to the well-being of our planet, continued growth of a society, and human development. Concrete is one of the most widely used construction materials in the world. However, the production of portland cement, an essential constituent of concrete, leads to the release of significant amounts of CO2 , a greenhouse gas (GHG); production of one ton of portland cement produces about one ton of CO2 and other GHGs. The environmental issues associated with GHGs, in addition to natural resources issues, will play a leading role in the sustainable development of the cement and concrete industry during this century. For example, as the supply of good-quality limestone to produce cement decreases, producing adequate amounts of portland cement for construction will become more difficult. There is a possibility that when there is no more good-quality limestone in, say, a geographical region, and thus no portland cement, all the employment associated with the concrete industry, as well as new c...


  • High-Carbon Fly Ash in Manufacturing Conductive CLSM and Concrete

    by Tarun R. Naik, Rudolph N. Kraus, Bruce W. Ramme, Yoon-Moon Chun, Rakesh Kumar

    Three controlled low-strength material (CLSM) mixtures (100, 100S with sand, and 100SG with sand and stone) were made using 93, 32, and 22% high-carbon fly ash (12% loss on ignition) by mass of total solids, respectively. Three concrete mixtures [40, 50 with steel fibers, and 60 with taconite (an iron ore) pellets] were made, each containing high-carbon fly ash at 43% of total cementitious materials. The respective 28-day electrical resistivity values of water-cured, saturated CLSM mixtures 100, 100S, and 100SG were 0.5, 1.0, and 1.8 Ω-m (ohm-m), and the corresponding values of water-cured, saturated concrete mixtures 40, 50, and 60 were 41, 15, and 17 Ω-m . As the amount of cementitious paste (including high-carbon fly ash) increased, electrical resistivity of CLSM decreased. Electrical resistivity of concrete reduced by more than half upon inclusion of 3% steel fibers or upon replacement of natural crushed stone with taconite pellets. This study also shows that high-carbon fly ash can be used in manufac...


  • Cast-Concrete Products Made with FBC Ash and Wet-Collected Coal-Ash

    by Tarun R. Naik, Rudolph N. Kraus, Yoon-Moon Chun, Francois D. Botha

    Cast-concrete hollow blocks, solid blocks, and paving stones were produced at a manufacturing plant by replacing up to 45% (by mass) of portland cement with fluidized bed combustion (FBC) coal ash and up to 9% of natural aggregates with wet-collected, low-lime, coarse coal-ash (WA). Cast-concrete product specimens of all three types exceeded the compressive strength requirements of ASTM from early ages, with the exception of one paving-stone mixture, which fell short of the requirement by less than 10%. The cast-concrete products made by replacing up to 40% of cement with FBC ash were equivalent in strength (89–113% of control) to the products without ash. The abrasion resistance of paving stones was equivalent for up to 34% FBC ash content. Partial replacement of aggregates with WA decreased strength of the products. The resistance of hollow blocks and paving stones to freezing and thawing decreased appreciably with increasing ash contents. The cast-concrete products could be used indoors in regions where freezing and thawing is a concern, and outdoors in a moderate climate.


  • Use of Residual Solids from Pulp and Paper Mills for Enhancing Strength and Durability of Ready-Mixed Concrete

    by Tarun R. Naik, Yoon-Moon Chun, Rudolph N. Kraus

    This research was conducted to establish mixture proportioning and production technologies for ready-mixed concrete containing pulp and paper mill residual solids and to study technical, economical, and performance benefits of using the residual solids in the concrete. Fibrous residuals generated from pulp and paper mills were used, and concrete mixture proportions and productions technologies were first optimized under controlled laboratory conditions. Based on the mixture proportions established in the laboratory, prototype field concrete mixtures were manufactured at a ready-mixed concrete plant. Afterward, a field construction demonstration was held to demonstrate the production and placement of structural-grade cold-weather-resistant concrete containing residual solids.


  • Strength and Durability of Roller-Compacted HVFA Concrete Pavements

    by Tarun R. Naik, Yoon-Moon Chun, Rudolph N. Kraus, Shiw S. Singh, Lori-Lynn C. Pennock, Bruce W. Ramme

    This investigation was conducted to collect state-of-the-art information on the strength and durability of roller-compacted concrete (RCC) for pavement construction made with and without supplementary cementitious materials, and to describe the construction experience gained in two pavement projects (Projects I and II) recently completed in Wisconsin. Project I deals with performance of conventional high-volume fly ash (HVFA) concrete pavement having a roller-compacted, no-fines permeable base course containing fly ash obtained from an SO2 control technology (dry desulphuring process), and Project II deals with RCC pavement (RCCP) containing 30% ASTM Class C fly ash. Past studies have shown that mechanical behavior of RCCP is similar to that of conventional paving concrete. However, nonair-entrained RCC is susceptible to freezing and thawing (F and T) damage if critically saturated when subjected to freezing actions. Laboratory testing of specimens derived from the pavements showed excellent results for conventional HVFA pavement, and satisfactory performance of the RCCP except for F and T resistance. Specimens from the RCCP performed poorly in laboratory freezing and thawing testing according to ASTM C 666, Procedure A. However, they showed adequate performance for up to 210 cycles of F and T when tested in accordance with ASTM C 666, Procedure B.