X. M. Ding
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
X. M. Ding has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Xiao-Yuan Hou
Fudan University
6 shared publications J. He
Surface Physics Laboratory (National Key Laboratory), Fudan University, Shanghai 200433, People’s Republic of China
3 shared publicationsH. Z. Shi
Surface Physics Laboratory (National Key Laboratory), Fudan University, Shanghai 200433, People’s Republic of China
2 shared publicationsS. T. Zhang
Surface Physics Laboratory (National Key Laboratory), Fudan University, Shanghai 200433, People’s Republic of China
2 shared publications- Wei Huang
School of Flexible Electronics (SoFE) and Henan Institute of Flexible Electronics (HIFE) Henan University Zhengzhou China
2 shared publications Z. Xu
Surface Physics Laboratory (National Key Laboratory), Fudan University, Shanghai 200433, People’s Republic of China
2 shared publications
Latest Publications
- 31 August 2009
- Published by Elsevier in Organic Electronics
- Vol. 10 (5) , 965-969
Loss and recovery of bistability of organic bistable devices
- 31 August 2009
- Published by Elsevier in Organic Electronics
- Vol. 10 (5) , 965-969
Loss and recovery of bistability of organic bistable devices
- 15 May 2009
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 105 (10) , 106105
Photoemission study of C60-induced barrier reduction for hole injection at N, N′-bis(naphthalene-1-y1)-N, N′-bis(phenyl) benzidine/Al
Synchrotron radiation photoemission study showed that the energy level alignment at the interface between , -bis(naphthalene-1-y1)- , -bis(phenyl) benzidine (NPB), a typical hole transport material, and Al could be adjusted by precovering a thin layer on Al. The interface dipoles so formed could shift both the highest occupied molecular orbital level of NPB and the secondary electron cutoff measured at the early stage of the NPB deposition. The barrier height for hole injection from Al to NPB could thus be lowered by as much as 0.98 eV, and the optimal thickness of the inserted layer was found to be 8–12 Å.- 15 May 2009
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 105 (10) , 106105
Photoemission study of C60-induced barrier reduction for hole injection at N, N′-bis(naphthalene-1-y1)-N, N′-bis(phenyl) benzidine/Al
Synchrotron radiation photoemission study showed that the energy level alignment at the interface between , -bis(naphthalene-1-y1)- , -bis(phenyl) benzidine (NPB), a typical hole transport material, and Al could be adjusted by precovering a thin layer on Al. The interface dipoles so formed could shift both the highest occupied molecular orbital level of NPB and the secondary electron cutoff measured at the early stage of the NPB deposition. The barrier height for hole injection from Al to NPB could thus be lowered by as much as 0.98 eV, and the optimal thickness of the inserted layer was found to be 8–12 Å.- 30 July 2002
- Published by AIP Publishing in Applied Physics Letters
- Vol. 81 (6) , 1122-1124
Aggregation and permeation of 4-(dicyanomethylene)-2-methyl-6-(p-dimethylaminostyryl)-4H-pyran molecules in Alq
The morphologic and luminescent behaviors of various 4-(dicyanomethylene)-2methyl-6-(p-dimethylaminostyryl)-4H-pyran (DCM) containing films have been investigated. This involves pure DCM layers deposited on top of a tris-(8-hydroxyquinoline) aluminum (Alq) layer or positioned between two Alq layer, DCM-doped Alq films, and periodically arranged Alq/DCM multilayer structures. The occurrence over a period of time of aggregation and permeation of DCM molecules at room temperature and at temperatures as low as is found in all the cases studied. Such a phenomenon will result in degradation of related organic light-emitting devices and is closely related to the electric polarity of the DCM molecule.- 30 July 2002
- Published by AIP Publishing in Applied Physics Letters
- Vol. 81 (6) , 1122-1124
Aggregation and permeation of 4-(dicyanomethylene)-2-methyl-6-(p-dimethylaminostyryl)-4H-pyran molecules in Alq
The morphologic and luminescent behaviors of various 4-(dicyanomethylene)-2methyl-6-(p-dimethylaminostyryl)-4H-pyran (DCM) containing films have been investigated. This involves pure DCM layers deposited on top of a tris-(8-hydroxyquinoline) aluminum (Alq) layer or positioned between two Alq layer, DCM-doped Alq films, and periodically arranged Alq/DCM multilayer structures. The occurrence over a period of time of aggregation and permeation of DCM molecules at room temperature and at temperatures as low as is found in all the cases studied. Such a phenomenon will result in degradation of related organic light-emitting devices and is closely related to the electric polarity of the DCM molecule.- 24 June 2002
- Published by AIP Publishing in Applied Physics Letters
- Vol. 80 (25) , 4846-4848
In situ photoluminescence investigation of doped Alq
We report the photoluminescence (PL) properties measured in situ from vacuum-deposited organic films of tris-(8-hydroxyquinoline) aluminum (Alq) doped with 4-(dicyanomethylene)-2-methyl-6(p-dimethylaminostyryl)-4H-pyran (DCM), where the red emission from the guest molecules is due to Förster energy transfer of excited state energy from host to guest. Both bare DCM-doped Alq (Alq:DCM) and bilayer Alq/Alq:DCM films have been studied, with the thickness of the Alq overlayer continuously varied in the latter case. The PL spectra from the bilayer structure contain no Alq contribution when its thickness is below 2.4 nm. Taking the value as the maximum distance for which the Alq exciton can travel in the film and still transfer its energy to a DCM molecule, the minimum DCM concentration in Alq:DCM necessary to produce red emission only can be estimated at 0.31 wt %. The most efficient red emission appears at the DCM concentration of about 1.7 wt %, at which more than 90% Alq-originated excitons are involved in the Förster energy transfer process. There exists a gradual red shift of the PL spectra with increasing DCM concentration, which can be attributed to the polarization and accompanying aggregation tendency of DCM molecules in Alq during the formation of the doped films.
- 24 June 2002
- Published by AIP Publishing in Applied Physics Letters
- Vol. 80 (25) , 4846-4848
In situ photoluminescence investigation of doped Alq
We report the photoluminescence (PL) properties measured in situ from vacuum-deposited organic films of tris-(8-hydroxyquinoline) aluminum (Alq) doped with 4-(dicyanomethylene)-2-methyl-6(p-dimethylaminostyryl)-4H-pyran (DCM), where the red emission from the guest molecules is due to Förster energy transfer of excited state energy from host to guest. Both bare DCM-doped Alq (Alq:DCM) and bilayer Alq/Alq:DCM films have been studied, with the thickness of the Alq overlayer continuously varied in the latter case. The PL spectra from the bilayer structure contain no Alq contribution when its thickness is below 2.4 nm. Taking the value as the maximum distance for which the Alq exciton can travel in the film and still transfer its energy to a DCM molecule, the minimum DCM concentration in Alq:DCM necessary to produce red emission only can be estimated at 0.31 wt %. The most efficient red emission appears at the DCM concentration of about 1.7 wt %, at which more than 90% Alq-originated excitons are involved in the Förster energy transfer process. There exists a gradual red shift of the PL spectra with increasing DCM concentration, which can be attributed to the polarization and accompanying aggregation tendency of DCM molecules in Alq during the formation of the doped films.
- 23 February 2000
- Published by Wiley in Advanced Materials
- Vol. 12 (4) , 265-269
Real-Time Observation of Temperature Rise and Thermal Breakdown Processes in Organic LEDs Using an IR Imaging and Analysis System
- 23 February 2000
- Published by Wiley in Advanced Materials
- Vol. 12 (4) , 265-269
Real-Time Observation of Temperature Rise and Thermal Breakdown Processes in Organic LEDs Using an IR Imaging and Analysis System
- 17 January 1994
- Published by AIP Publishing in Applied Physics Letters
- Vol. 64 (3) , 315-317
Molecular-beam-epitaxy growth of GaN on GaAs(100) by using reactive nitrogen source
By using a cold cathode ion gun to ionize the nitrogen gas, the molecular-beam-epitaxy growth of GaN is carried out. The zinc-blende structure GaN epilayer grown on the GaAs(100) substrate with a narrow x-ray diffraction peak width (FWHM) of 23 min and a low carrier concentration of 1017 cm−3 is achieved. The surface optical phonon energies of cubic and hexagonal GaN are experimentally determined to be 82 and 90 meV, respectively.
- 17 January 1994
- Published by AIP Publishing in Applied Physics Letters
- Vol. 64 (3) , 315-317
Molecular-beam-epitaxy growth of GaN on GaAs(100) by using reactive nitrogen source
By using a cold cathode ion gun to ionize the nitrogen gas, the molecular-beam-epitaxy growth of GaN is carried out. The zinc-blende structure GaN epilayer grown on the GaAs(100) substrate with a narrow x-ray diffraction peak width (FWHM) of 23 min and a low carrier concentration of 1017 cm−3 is achieved. The surface optical phonon energies of cubic and hexagonal GaN are experimentally determined to be 82 and 90 meV, respectively.