Nivaldo Lemos Coppini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Nivaldo Lemos Coppini has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Elesandro Antonio Baptista
Nove de Julho University
6 shared publications Fábio Henrique Pereira
2 shared publicationsRafael Do Espírito-Santo
2 shared publicationsAdemir De Oliveira
1 shared publicationAdemir João De Oliveira
1 shared publicationAdemir João de Oliveira
Uninove, SP
1 shared publication
Latest Publications
- 20 April 2017
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 39 (9) , 3581-3589
Drilling analysis of cemented carbide drills after chemical treatment under low heating
- 20 April 2017
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 39 (9) , 3581-3589
Drilling analysis of cemented carbide drills after chemical treatment under low heating
- 5 February 2015
- Published by Springer Nature
- p. 235-245
Increasing Production and Minimizing Costs During Machining by Control of Tool’s Wears and or Damages
- 5 February 2015
- Published by Springer Nature
- p. 235-245
Increasing Production and Minimizing Costs During Machining by Control of Tool’s Wears and or Damages
- 23 May 2013
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 35 (4) , 347-355
Profit optimization in machining service providers using principles of the Theory of Constraints
- 23 May 2013
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 35 (4) , 347-355
Profit optimization in machining service providers using principles of the Theory of Constraints
- Open Access
- 9 April 2012
- Published by University Nove de Julho in Exacta
- Vol. 10 (1)
Desafios Enfrentados pelos Fornecedores de Sistemas de Gerenciamento de Usinagem
- 9 April 2012
- Published by University Nove de Julho in Exacta
- Vol. 10 (1)
Open AccessDesafios Enfrentados pelos Fornecedores de Sistemas de Gerenciamento de Usinagem
- Open Access
- 9 April 2012
- Published by University Nove de Julho in Exacta
- Vol. 10 (1)
Flexible machining environments – tests on the shop floor in order to minimize setup times
- 9 April 2012
- Published by University Nove de Julho in Exacta
- Vol. 10 (1)
Open AccessFlexible machining environments – tests on the shop floor in order to minimize setup times
- Open Access
- 30 August 2010
- Published by University Nove de Julho in Exacta
- Vol. 8 (2) , 225-235
Low-loss image compression techniques for cutting tool images: a comparative study of compression quality measures DOI: 10.5585/exacta.v8i2.2000
This work accomplishes a comparative study between two distinct image compression techniques, namely the Lifting technique and the Principal Components Analysis (PCA), in order to determine what of these two approaches is more appropriate for cutting tool wear images analysis. Lifting and Principal Components Analysis were applied in original images of a cutting tool for producing a low resolution version, while keeping the more important details of the image. The low-loss image compression quality provided by these techniques was expressed in terms of the compression factor (ρ), the Mean Square Error (MSE) and the Peak Signal-to-Noise Rate (PSNR) provided by the image compression process. The tests were accomplished using the high-performance language for technical computing MATLAB®, and the results shown that the PCA technique presented the best values of PSNR with low compression rates. However, with high values of compression rates the lifting technique gave the highest PSNR.
- 30 August 2010
- Published by University Nove de Julho in Exacta
- Vol. 8 (2) , 225-235
Open AccessLow-loss image compression techniques for cutting tool images: a comparative study of compression quality measures DOI: 10.5585/exacta.v8i2.2000
This work accomplishes a comparative study between two distinct image compression techniques, namely the Lifting technique and the Principal Components Analysis (PCA), in order to determine what of these two approaches is more appropriate for cutting tool wear images analysis. Lifting and Principal Components Analysis were applied in original images of a cutting tool for producing a low resolution version, while keeping the more important details of the image. The low-loss image compression quality provided by these techniques was expressed in terms of the compression factor (ρ), the Mean Square Error (MSE) and the Peak Signal-to-Noise Rate (PSNR) provided by the image compression process. The tests were accomplished using the high-performance language for technical computing MATLAB®, and the results shown that the PCA technique presented the best values of PSNR with low compression rates. However, with high values of compression rates the lifting technique gave the highest PSNR.
- Open Access
- 30 August 2010
- Published by University Nove de Julho in Exacta
- Vol. 8 (2) , 225-235
Low-loss image compression techniques for cutting tool images: a comparative study of compression quality measures
This work accomplishes a comparative study between two distinct image compression techniques, namely the Lifting technique and the Principal Components Analysis (PCA), in order to determine what of these two approaches is more appropriate for cutting tool wear images analysis. Lifting and Principal Components Analysis were applied in original images of a cutting tool for producing a low resolution version, while keeping the more important details of the image. The low-loss image compression quality provided by these techniques was expressed in terms of the compression factor (ρ), the Mean Square Error (MSE) and the Peak Signal-to-Noise Rate (PSNR) provided by the image compression process. The tests were accomplished using the high-performance language for technical computing MATLAB®, and the results shown that the PCA technique presented the best values of PSNR with low compression rates. However, with high values of compression rates the lifting technique gave the highest PSNR.
- 30 August 2010
- Published by University Nove de Julho in Exacta
- Vol. 8 (2) , 225-235
Open AccessLow-loss image compression techniques for cutting tool images: a comparative study of compression quality measures
This work accomplishes a comparative study between two distinct image compression techniques, namely the Lifting technique and the Principal Components Analysis (PCA), in order to determine what of these two approaches is more appropriate for cutting tool wear images analysis. Lifting and Principal Components Analysis were applied in original images of a cutting tool for producing a low resolution version, while keeping the more important details of the image. The low-loss image compression quality provided by these techniques was expressed in terms of the compression factor (ρ), the Mean Square Error (MSE) and the Peak Signal-to-Noise Rate (PSNR) provided by the image compression process. The tests were accomplished using the high-performance language for technical computing MATLAB®, and the results shown that the PCA technique presented the best values of PSNR with low compression rates. However, with high values of compression rates the lifting technique gave the highest PSNR.