Zhongming Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhongming Zhang has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
C.J. Xu
School of Materials Science & Engineering, Xi'an University of Technology, Xi'an 710048, China
3 shared publicationsChunjie Xu
3 shared publications- Jincheng Wang
State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China
3 shared publications Can Guo
School of Materials Science and Engineering, Xi’an University of Technology, Xi’an, China
2 shared publications- Chunjie Xu
School of Materials Science and Engineering, Xi’an University of Technology, Xi’an 710048, China
2 shared publications Feng Chen
Guangdong-Hong Kong Joint Research and Development Center on Advanced Manufacturing Technology for Light Alloys, Institute of New Materials, Guangdong Academy of Sciences, Guangzhou, China
2 shared publications
Latest Publications
- Open Access
- 24 October 2026
- Published by Elsevier in SSRN Electronic Journal
Synergistic Optimization of Deformation and Removability for Laser Powder Bed Fusion Support Structures via Active Learning
Support structures play a pivotal role in mitigating the deformation of overhanging geometries in laser powder bed fusion. Their design necessitates a critical trade-off: they must provide robust mechanical integrity and efficient heat dissipation to prevent distortion, while remaining easily removable during post-processing. To address this challenge, a framework coupling an active learning strategy with Finite Element Method simulations was developed to optimize block support parameters. The framework exploits the asymmetric objective structure in which removability is analytically deterministic while deformation requires expensive simulation, formulating the problem as Pareto optimization of a black-box deformation objective against a closed-form removability metric. Within only five iterations, the framework significantly broadened the Pareto front for the dual objectives of minimizing overhang deformation and improving support removability, identifying an optimized set of parameter combinations whose performance surpassed results reported in the literature. Subsequent experiments confirmed the framework's efficacy in parameter recommendation. Furthermore, a comprehensive summary of the support parameters corresponding to the Pareto front derived from both this study and existing literature is provided, offering practical guidance for the rational selection of block support parameters.
- 24 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSynergistic Optimization of Deformation and Removability for Laser Powder Bed Fusion Support Structures via Active Learning
Support structures play a pivotal role in mitigating the deformation of overhanging geometries in laser powder bed fusion. Their design necessitates a critical trade-off: they must provide robust mechanical integrity and efficient heat dissipation to prevent distortion, while remaining easily removable during post-processing. To address this challenge, a framework coupling an active learning strategy with Finite Element Method simulations was developed to optimize block support parameters. The framework exploits the asymmetric objective structure in which removability is analytically deterministic while deformation requires expensive simulation, formulating the problem as Pareto optimization of a black-box deformation objective against a closed-form removability metric. Within only five iterations, the framework significantly broadened the Pareto front for the dual objectives of minimizing overhang deformation and improving support removability, identifying an optimized set of parameter combinations whose performance surpassed results reported in the literature. Subsequent experiments confirmed the framework's efficacy in parameter recommendation. Furthermore, a comprehensive summary of the support parameters corresponding to the Pareto front derived from both this study and existing literature is provided, offering practical guidance for the rational selection of block support parameters.
- Open Access
- 19 May 2026
- Published by Elsevier in SSRN Electronic Journal
Synergistic Optimization of Deformation and Removability for LPBF Support Structures via Active Learning
Support structures play a pivotal role in mitigating the deformation of overhanging geometries in laser powder bed fusion. Their design necessitates a critical trade-off: they must provide robust mechanical integrity and efficient heat dissipation to prevent distortion, while remaining easily removable during post-processing. To address this challenge, a framework coupling an active learning strategy with Finite Element Method (FEM) simulations was developed to optimize block support parameters. Within only five iterations, the framework significantly broadened the Pareto front for the dual objectives of minimizing overhang deformation and improving support removability, identifying an optimized set of parameter combinations whose performance surpassed results reported in the literature. Subsequent experiments confirmed the framework's efficacy in parameter recommendation. Furthermore, a comprehensive summary of the support parameters corresponding to the Pareto front derived from both this study and existing literature is provided, offering practical guidance for the rational selection of block support parameters.
- 19 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSynergistic Optimization of Deformation and Removability for LPBF Support Structures via Active Learning
Support structures play a pivotal role in mitigating the deformation of overhanging geometries in laser powder bed fusion. Their design necessitates a critical trade-off: they must provide robust mechanical integrity and efficient heat dissipation to prevent distortion, while remaining easily removable during post-processing. To address this challenge, a framework coupling an active learning strategy with Finite Element Method (FEM) simulations was developed to optimize block support parameters. Within only five iterations, the framework significantly broadened the Pareto front for the dual objectives of minimizing overhang deformation and improving support removability, identifying an optimized set of parameter combinations whose performance surpassed results reported in the literature. Subsequent experiments confirmed the framework's efficacy in parameter recommendation. Furthermore, a comprehensive summary of the support parameters corresponding to the Pareto front derived from both this study and existing literature is provided, offering practical guidance for the rational selection of block support parameters.
- 22 April 2026
- Published by Springer Nature in China Foundry
- Vol. 23 (4) , 1-11
Enhancing forming quality, refining grains, and reducing anisotropy of mechanical properties of WAAM-processed AZ31 alloy by welding torch wobbling
- 22 April 2026
- Published by Springer Nature in China Foundry
- Vol. 23 (4) , 1-11
Enhancing forming quality, refining grains, and reducing anisotropy of mechanical properties of WAAM-processed AZ31 alloy by welding torch wobbling
- Open Access
- 17 May 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 8698-8710
Melting behavior of VNbMoTa particle and its influence on microstructure and mechanical properties of laser additively manufactured nickel matrix composites
- 17 May 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 8698-8710
Open AccessMelting behavior of VNbMoTa particle and its influence on microstructure and mechanical properties of laser additively manufactured nickel matrix composites
- Open Access
Effect of Electropulsing Current Density on the Strength–Ductility Synergy of Extruded Mg-6Al-1Zn Alloy
The difficulty in enhancing both tensile strength and ductility is limiting the development of high-performance Mg alloys. The “plastic deformation + electropulsing (EP) treatment” is an effective process for modifying the microstructure and enhancing the mechanical properties of metals. In this work, the influence of the current density of EP treatment on the microstructure and tensile property evolution of the as-extruded Mg-6Al-1Zn alloy was systematically investigated. The microstructure of the as-extruded sample was predominantly composed of an α-Mg matrix and a minor quantity of the β-Mg17Al12 phase on grain boundaries. After EP treatments, the microstructure underwent recrystallization, resulting in the formation of fine recrystallized grains. Meanwhile, the distribution and volume fraction of the β-Mg17Al12 phase demonstrated minor changes. After the 60 cycles of EP with a current density of 1050 A·mm−2 for a duration of 60 s, the tensile strength and elongation of the as-extruded Mg-6Al-1Zn alloy improved from 260 ± 2.6 MPa and 22 ± 1.3% to 319 ± 3.6 MPa and 23 ± 1.1%, respectively. The results prove the effectiveness of EP treatment in tailoring recrystallization via changing current density.
Open AccessEffect of Electropulsing Current Density on the Strength–Ductility Synergy of Extruded Mg-6Al-1Zn Alloy
The difficulty in enhancing both tensile strength and ductility is limiting the development of high-performance Mg alloys. The “plastic deformation + electropulsing (EP) treatment” is an effective process for modifying the microstructure and enhancing the mechanical properties of metals. In this work, the influence of the current density of EP treatment on the microstructure and tensile property evolution of the as-extruded Mg-6Al-1Zn alloy was systematically investigated. The microstructure of the as-extruded sample was predominantly composed of an α-Mg matrix and a minor quantity of the β-Mg17Al12 phase on grain boundaries. After EP treatments, the microstructure underwent recrystallization, resulting in the formation of fine recrystallized grains. Meanwhile, the distribution and volume fraction of the β-Mg17Al12 phase demonstrated minor changes. After the 60 cycles of EP with a current density of 1050 A·mm−2 for a duration of 60 s, the tensile strength and elongation of the as-extruded Mg-6Al-1Zn alloy improved from 260 ± 2.6 MPa and 22 ± 1.3% to 319 ± 3.6 MPa and 23 ± 1.1%, respectively. The results prove the effectiveness of EP treatment in tailoring recrystallization via changing current density.
- 25 July 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (11) , 10013-10023
Achieving High Strength and Ductility in Hot-Rolled Mg-3.5Al-3Nd Alloy via Microstructure Adjustment
- 25 July 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (11) , 10013-10023
Achieving High Strength and Ductility in Hot-Rolled Mg-3.5Al-3Nd Alloy via Microstructure Adjustment
- 10 April 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 33 (6) , 2599-2606
Microstructures and Mechanical Properties of Hot-Rolled Mg-Al-Ce Ternary Alloy Sheets with Different Al Contents
- 10 April 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 33 (6) , 2599-2606
Microstructures and Mechanical Properties of Hot-Rolled Mg-Al-Ce Ternary Alloy Sheets with Different Al Contents
- 1 September 2017
- Published by Elsevier in Rare Metal Materials and Engineering
- Vol. 46 (9) , 2352-2358
Mechanical Properties and Corrosion Behavior of Hot Extruded Mg 99.2 Ca 0.6 Mn 0.2 Alloy in SBF Solution
- 1 September 2017
- Published by Elsevier in Rare Metal Materials and Engineering
- Vol. 46 (9) , 2352-2358
Mechanical Properties and Corrosion Behavior of Hot Extruded Mg 99.2 Ca 0.6 Mn 0.2 Alloy in SBF Solution
- 1 August 2008
- Published by Elsevier in Acta Metallurgica Sinica (English Letters)
- Vol. 21 (4) , 275-281
Microstructure of binary Mg-Al eutectic alloy wires produced by the Ohno continuous casting process
- 1 August 2008
- Published by Elsevier in Acta Metallurgica Sinica (English Letters)
- Vol. 21 (4) , 275-281
Microstructure of binary Mg-Al eutectic alloy wires produced by the Ohno continuous casting process
- 29 February 2008
- Published by Elsevier in Acta Metallurgica Sinica (English Letters)
- Vol. 21 (1) , 30-36
Microstructure of Mg-6.4Zn-1.1Y alloy fabricated by rapid solidification and reciprocating extrusion
- 29 February 2008
- Published by Elsevier in Acta Metallurgica Sinica (English Letters)
- Vol. 21 (1) , 30-36
Microstructure of Mg-6.4Zn-1.1Y alloy fabricated by rapid solidification and reciprocating extrusion