Takeshi Ohbuchi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Takeshi Ohbuchi has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Naoto Wakatsuki
Faculty of Engineering, Information and Systems, University of Tsukuba, Ibaraki, Japan
13 shared publicationsKoichi Mizutani
Faculty of Engineering, Information and Systems, University of Tsukuba, Ibaraki, Japan
11 shared publicationsFujihiko Matsumoto
Department of Applied Physics National Defence Academy 1‐10‐20 Hashirimizu Yokosuka 239–8686 Japan
9 shared publicationsHiroyuki Masuyama
Toba National College of Maritime Technology
8 shared publicationsTadashi Ebihara
5 shared publicationsTakanobu Kuroyama
Graduate School of System and Information Engineering, University of Tsukuba, Ibaraki, Japan
5 shared publications
Latest Publications
- 12 May 2021
- Published by Wiley in IEEJ Transactions on Electrical and Electronic Engineering
- Vol. 16 (7) , 988-995
A Three‐stage programmable impedance scaling circuit
- 12 May 2021
- Published by Wiley in IEEJ Transactions on Electrical and Electronic Engineering
- Vol. 16 (7) , 988-995
A Three‐stage programmable impedance scaling circuit
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 55-60
A design method of low frequency universal filter employing MOCCIIs
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 55-60
A design method of low frequency universal filter employing MOCCIIs
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 95-100
Improvement technique of tuning range for local-feedback MOS transconductor
A local-feedback transconductor (LFB OTA) is a linear OTA operating in a saturation region. In addition, the LFB OTA operating in a subthreshold region, whose transfer characteristics are expressed by a sinh function, is utilized for low-power and low-transconductance linear OTAs. However, the LFB OTA has a limit of a tuning range of a transconductance because of a local-feedback structure. To improve the tuning range, a local-feedback circuit which is composed of pMOS transistor is used for replacing the conventional one which is composed of nMOS transistor. The proposed OTA operating in the subthreshold region works as long as a reference current source circuit works. The operating current is used to tune the transconductance of the proposed OTA. The frequency characteristics, the CMRR, and the input refereed noise of the proposed OTA are almost the same as that of the conventional LFB OTA. From the Monte Carlo simulation, the sensitivity to the size mismatch of the proposed OTA is smaller than the one of the conventional LFB OTA. The validity of the proposed technique is confirmed by simulations.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 95-100
Improvement technique of tuning range for local-feedback MOS transconductor
A local-feedback transconductor (LFB OTA) is a linear OTA operating in a saturation region. In addition, the LFB OTA operating in a subthreshold region, whose transfer characteristics are expressed by a sinh function, is utilized for low-power and low-transconductance linear OTAs. However, the LFB OTA has a limit of a tuning range of a transconductance because of a local-feedback structure. To improve the tuning range, a local-feedback circuit which is composed of pMOS transistor is used for replacing the conventional one which is composed of nMOS transistor. The proposed OTA operating in the subthreshold region works as long as a reference current source circuit works. The operating current is used to tune the transconductance of the proposed OTA. The frequency characteristics, the CMRR, and the input refereed noise of the proposed OTA are almost the same as that of the conventional LFB OTA. From the Monte Carlo simulation, the sensitivity to the size mismatch of the proposed OTA is smaller than the one of the conventional LFB OTA. The validity of the proposed technique is confirmed by simulations.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Study on offset reduction method for a fully differential filter employing symmetrical floating impedance scaling circuits
In this paper, a method to reduce the offset voltage of a fully differential filter employing symmetry-type floating impedance scaling (SFIS) circuits with prevention of wasteful power consumption is proposed. The problem of the filter employing the conventional SFIS circuit and a common-mode rejection (CMR) circuit is that DC offset voltages are high. In order to reduce the offset voltages, much operating currents are necessary for high gain amplifier in the CMR circuit. The proposed solution is to reduce the offset voltage by unifying a common-mode feedback (CMFB) circuit and the SFIS circuit unlike an ordinary way that the CMFB is combined with an OTA or an OPamp. The validity of the proposed technique is examined by simulation. The offset voltage of the 1st-order fully differential active lowpass filter employing the proposed circuit is about 1.56mV. Comparing the current consumption of proposed and the conventional SFIS circuits, the proposed one is reduced by 35.5%.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Study on offset reduction method for a fully differential filter employing symmetrical floating impedance scaling circuits
In this paper, a method to reduce the offset voltage of a fully differential filter employing symmetry-type floating impedance scaling (SFIS) circuits with prevention of wasteful power consumption is proposed. The problem of the filter employing the conventional SFIS circuit and a common-mode rejection (CMR) circuit is that DC offset voltages are high. In order to reduce the offset voltages, much operating currents are necessary for high gain amplifier in the CMR circuit. The proposed solution is to reduce the offset voltage by unifying a common-mode feedback (CMFB) circuit and the SFIS circuit unlike an ordinary way that the CMFB is combined with an OTA or an OPamp. The validity of the proposed technique is examined by simulation. The offset voltage of the 1st-order fully differential active lowpass filter employing the proposed circuit is about 1.56mV. Comparing the current consumption of proposed and the conventional SFIS circuits, the proposed one is reduced by 35.5%.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
A linear transconductor utilizing body transconductance for low-power and low frequency applications
Low-frequency and low-power circuits for medical devices used in daily life, such as biomedical implants, are required. For the applications, a linear low-transconductance and low-power transconductor is needed. In this paper, a low-transconductance linear transconductor which is improved in a power efficiency of the transconductance utilizing control of the body transconductances of the input transistors is proposed. The validity of proposed transconductor is confirmed by simulations on condition that the transconductance was 1.0 uS. The linearity of the proposed transconductor, whose linear input range is 112 mV, is improved. The power consumption is 976 nW, and the power consumption of the conventional transconductor is reduced by 27%. Considering the linearity of transfer characteristics and power efficiency, availability of the proposed transconductor is confirmed.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
A linear transconductor utilizing body transconductance for low-power and low frequency applications
Low-frequency and low-power circuits for medical devices used in daily life, such as biomedical implants, are required. For the applications, a linear low-transconductance and low-power transconductor is needed. In this paper, a low-transconductance linear transconductor which is improved in a power efficiency of the transconductance utilizing control of the body transconductances of the input transistors is proposed. The validity of proposed transconductor is confirmed by simulations on condition that the transconductance was 1.0 uS. The linearity of the proposed transconductor, whose linear input range is 112 mV, is improved. The power consumption is 976 nW, and the power consumption of the conventional transconductor is reduced by 27%. Considering the linearity of transfer characteristics and power efficiency, availability of the proposed transconductor is confirmed.
- 20 August 2015
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 85 (2) , 263-273
A low-power and low-Gm linear transconductor utilizing control of a threshold voltage
- 20 August 2015
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 85 (2) , 263-273
A low-power and low-Gm linear transconductor utilizing control of a threshold voltage
- Open Access
- 21 June 2015
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 85 (2) , 253-261
Design of a symmetry-type floating impedance scaling circuits for a fully differential filter
- 21 June 2015
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 85 (2) , 253-261
Open AccessDesign of a symmetry-type floating impedance scaling circuits for a fully differential filter
- 1 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1448-1451
Measurement of convergence ultrasound in cone-like bubble structure using light deflection method
High intensity ultrasound irradiated from a horn surface in water forms a cone-like bubble structure (CBS). The ultrasound field in the CBS is highly nonlinear and converged at a certain point distant from the horn surface on the horn axis. The mechanism of the CBS was investigated and partly confirmed by the computer simulation. However, the experimental data of the acoustic cavitation field and the pressure field in the CBS are not enough. In this report, the measurement method of the low frequency ultrasound field formed in the bubbly water using the laser deflection and the acoustic cavitation bubble distribution using the laser scattering were proposed. The proposed method was applied to the measurement of the CBS under the horn with 30 mm diameter irradiating 19.2 kHz ultrasound at input power to the transducer is 90 W. The cross-sectional ultrasound and acoustic cavitation fields were obtained and the qualitative agreement of behavior of measured and previously reported fields were confirmed.
- 1 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1448-1451
Measurement of convergence ultrasound in cone-like bubble structure using light deflection method
High intensity ultrasound irradiated from a horn surface in water forms a cone-like bubble structure (CBS). The ultrasound field in the CBS is highly nonlinear and converged at a certain point distant from the horn surface on the horn axis. The mechanism of the CBS was investigated and partly confirmed by the computer simulation. However, the experimental data of the acoustic cavitation field and the pressure field in the CBS are not enough. In this report, the measurement method of the low frequency ultrasound field formed in the bubbly water using the laser deflection and the acoustic cavitation bubble distribution using the laser scattering were proposed. The proposed method was applied to the measurement of the CBS under the horn with 30 mm diameter irradiating 19.2 kHz ultrasound at input power to the transducer is 90 W. The cross-sectional ultrasound and acoustic cavitation fields were obtained and the qualitative agreement of behavior of measured and previously reported fields were confirmed.
- 18 June 2014
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 53 (7S) , 07KE12
Measurement of pressure amplitude of ultrasonic standing wave based on method of obtaining optical wavefront using phase retrieval
- 18 June 2014
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 53 (7S) , 07KE12
Measurement of pressure amplitude of ultrasonic standing wave based on method of obtaining optical wavefront using phase retrieval
- 1 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 391-396
Design of a floating-type impedance scaling circuit for large capacitances
Impedance scaling technique is known as a method to reduce chip area of large capacitances for low frequency integrated filters. The conventional technique realizes only grounded low impedance components. This paper proposes a construction of a floating-type impedance scaling circuit. The proposed circuit can be applied to various low frequency analog circuits. The validity of the proposed circuit is confirmed by simulation of a biquad filter employing the proposed circuit.
- 1 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 391-396
Design of a floating-type impedance scaling circuit for large capacitances
Impedance scaling technique is known as a method to reduce chip area of large capacitances for low frequency integrated filters. The conventional technique realizes only grounded low impedance components. This paper proposes a construction of a floating-type impedance scaling circuit. The proposed circuit can be applied to various low frequency analog circuits. The validity of the proposed circuit is confirmed by simulation of a biquad filter employing the proposed circuit.