Cihat Tascioglu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Cihat Tascioglu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Kenji Umemura
Kyoto University
3 shared publicationsPaul Cooper
Faculty of Forestry, University of Toronto, Toronto, Canada
3 shared publicationsTony Ung
Faculty of Forestry, University of Toronto, Toronto, Canada
3 shared publicationsTsuyoshi Yoshimura
Kyoto University
3 shared publicationsKunio Tsunoda
Kyoto Univ, Res Inst Sustainable Humanosphere, Uji, Kyoto 6110011, Japan
2 shared publicationsCaglar Akcay
Düzce University
1 shared publication
Latest Publications
- 4 November 2019
- Published by BioResources in BioResources
- Vol. 15 (1) , 20-27
Mold and larvae resistance of wood-based composites incorporating sodium fluoride
- 4 November 2019
- Published by BioResources in BioResources
- Vol. 15 (1) , 20-27
Mold and larvae resistance of wood-based composites incorporating sodium fluoride
- 7 August 2017
- Published by Springer Nature in Journal of Wood Science
- Vol. 63 (6) , 652-657
Potential utilization of sodium fluoride (NaF) as a biocide in particleboard production
- 7 August 2017
- Published by Springer Nature in Journal of Wood Science
- Vol. 63 (6) , 652-657
Potential utilization of sodium fluoride (NaF) as a biocide in particleboard production
- 1 February 2014
- Published by Elsevier in Composites Part B: Engineering
- Vol. 57, 31-34
Biological performance of zinc borate-incorporated particleboard: Effects of leaching on efficacy
- 1 February 2014
- Published by Elsevier in Composites Part B: Engineering
- Vol. 57, 31-34
Biological performance of zinc borate-incorporated particleboard: Effects of leaching on efficacy
- 1 April 2010
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 64 (3)
Biological performance of copper azole-treated wood and wood-based composites
Vacuum-impregnation with copper azole was applied as a post-treatment to five commercially available wood-based composites with thicknesses of approximately 12 mm, such as softwood plywood (SWP), hardwood plywood (HWP), medium density fiberboard (MDF), oriented strand board (OSB), and particleboard (PB). Untreated and treated composites were tested for their resistance to decay fungi (brown rot fungus Fomitopsis palustris and white rot fungus Trametes versicolor) and the subterranean termite Coptotermes formosanus by Japanese standardized laboratory test methods. Untreated MDF was highly resistant to both biological attacks and seemed to require no preservative treatment under less hazardous conditions, i.e., under protected and above-ground applications, with possible occasional wetting. PB was ranked second, and needed further protection only against C. formosanus. Copper azole did not adequately protect SWP from F. palustris and termite. OSB was not protected either against F. palustris and T. versicolor even at a concentration level of 1 kg copper azole per m3 in contrary to blocks of Cryptomeria japonica sapwood, which was protected at these concentration levels. The biological resistance of HWP was reasonably improved by copper azole. The performance of wood-based composites treated with copper azole, which was inferior to the biological resistance of treated C. japonica sapwood blocks, might depend on the thickness or layer profile, density as a result of porosity, uneven distribution of the preservative in the composites, and the susceptibility of the component raw materials.
- 1 April 2010
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 64 (3)
Biological performance of copper azole-treated wood and wood-based composites
Vacuum-impregnation with copper azole was applied as a post-treatment to five commercially available wood-based composites with thicknesses of approximately 12 mm, such as softwood plywood (SWP), hardwood plywood (HWP), medium density fiberboard (MDF), oriented strand board (OSB), and particleboard (PB). Untreated and treated composites were tested for their resistance to decay fungi (brown rot fungus Fomitopsis palustris and white rot fungus Trametes versicolor) and the subterranean termite Coptotermes formosanus by Japanese standardized laboratory test methods. Untreated MDF was highly resistant to both biological attacks and seemed to require no preservative treatment under less hazardous conditions, i.e., under protected and above-ground applications, with possible occasional wetting. PB was ranked second, and needed further protection only against C. formosanus. Copper azole did not adequately protect SWP from F. palustris and termite. OSB was not protected either against F. palustris and T. versicolor even at a concentration level of 1 kg copper azole per m3 in contrary to blocks of Cryptomeria japonica sapwood, which was protected at these concentration levels. The biological resistance of HWP was reasonably improved by copper azole. The performance of wood-based composites treated with copper azole, which was inferior to the biological resistance of treated C. japonica sapwood blocks, might depend on the thickness or layer profile, density as a result of porosity, uneven distribution of the preservative in the composites, and the susceptibility of the component raw materials.
- 30 October 2008
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 67 (1) , 7-12
Effects of delayed drying and CO2 application on copper amine fixation in ACQ treated red pine
- 30 October 2008
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 67 (1) , 7-12
Effects of delayed drying and CO2 application on copper amine fixation in ACQ treated red pine
- 18 January 2008
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 62 (3) , 289-293
Effects of fixation temperature and environment on copper speciation in ACQ treated red pine
Red pine (Pinus resinosa Ait.) sapwood samples treated with alkaline (amine) copper quaternary (ACQ) were conditioned at different temperatures and under wet or dry conditions to evaluate the stability of copper (Cu) to leaching and conversion of divalent copper (Cu-II) to monovalent copper (Cu-I). Significant Cu-II was reduced to Cu-I during post-treatment stabilization, especially at elevated temperatures (105°C and 120°C). The percent conversion to Cu-I was higher at lower retentions; in some cases, at low retentions and high fixation temperatures, all of the cupric Cu was reduced to Cu-I, raising the possibility of reduced activity of Cu as a biocide when high temperature conditions are used to fix ACQ treated wood. However, exposure of wood to a leaching procedure (rewetting, re-drying) generally resulted in a significant component of the Cu-I in wood being oxidized back to Cu-II. Steaming of weathered ACQ treated wood at 120°C also converted significant amounts of Cu-II to Cu-I.
- 18 January 2008
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 62 (3) , 289-293
Effects of fixation temperature and environment on copper speciation in ACQ treated red pine
Red pine (Pinus resinosa Ait.) sapwood samples treated with alkaline (amine) copper quaternary (ACQ) were conditioned at different temperatures and under wet or dry conditions to evaluate the stability of copper (Cu) to leaching and conversion of divalent copper (Cu-II) to monovalent copper (Cu-I). Significant Cu-II was reduced to Cu-I during post-treatment stabilization, especially at elevated temperatures (105°C and 120°C). The percent conversion to Cu-I was higher at lower retentions; in some cases, at low retentions and high fixation temperatures, all of the cupric Cu was reduced to Cu-I, raising the possibility of reduced activity of Cu as a biocide when high temperature conditions are used to fix ACQ treated wood. However, exposure of wood to a leaching procedure (rewetting, re-drying) generally resulted in a significant component of the Cu-I in wood being oxidized back to Cu-II. Steaming of weathered ACQ treated wood at 120°C also converted significant amounts of Cu-II to Cu-I.
- 1 September 2005
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 59 (5) , 574-580
Rate and extent of adsorption of ACQ preservative components in wood
The adsorption of copper, [as Cu(II)], monoethanolamine (MEA) and didecyldimethyl ammonium chloride (DDAC) components of CuMEA and alkaline copper quaternary (ACQ) solutions impregnated into wood was followed by measuring the changes in solution concentrations in the wood over time. The rate and extent of copper and MEA adsorption were highly dependent on the solution strength and the conditioning temperature. Both copper and MEA were adsorbed by the wood structure with a rapid initial reaction, with higher relative amounts sorbed from lower concentration solutions. This was followed by a slower adsorption that still had not equilibrated after 7 weeks at 22°C. Generally, the adsorption pattern was similar for copper and MEA, suggesting that they were adsorbed as a copper MEA complex, with an MEA/copper molar ratio close to the theoretical maximum of 4. At a higher conditioning temperature of 50°C the reaction time was greatly reduced, with the adsorption after 1 week higher than after 7 weeks at 22°C, suggesting faster and more complete reaction at higher temperatures. DDAC was adsorbed more quickly and to a higher degree than Cu(II) for all treatment solutions and should be preferentially removed from such solutions, especially if empty-cell treatments are used. There appeared to be higher Cu adsorption from the higher concentration solutions of CuMEA than from corresponding ACQ solutions, likely due to DDAC competition with copper for the same reaction sites.
- 1 September 2005
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 59 (5) , 574-580
Rate and extent of adsorption of ACQ preservative components in wood
The adsorption of copper, [as Cu(II)], monoethanolamine (MEA) and didecyldimethyl ammonium chloride (DDAC) components of CuMEA and alkaline copper quaternary (ACQ) solutions impregnated into wood was followed by measuring the changes in solution concentrations in the wood over time. The rate and extent of copper and MEA adsorption were highly dependent on the solution strength and the conditioning temperature. Both copper and MEA were adsorbed by the wood structure with a rapid initial reaction, with higher relative amounts sorbed from lower concentration solutions. This was followed by a slower adsorption that still had not equilibrated after 7 weeks at 22°C. Generally, the adsorption pattern was similar for copper and MEA, suggesting that they were adsorbed as a copper MEA complex, with an MEA/copper molar ratio close to the theoretical maximum of 4. At a higher conditioning temperature of 50°C the reaction time was greatly reduced, with the adsorption after 1 week higher than after 7 weeks at 22°C, suggesting faster and more complete reaction at higher temperatures. DDAC was adsorbed more quickly and to a higher degree than Cu(II) for all treatment solutions and should be preferentially removed from such solutions, especially if empty-cell treatments are used. There appeared to be higher Cu adsorption from the higher concentration solutions of CuMEA than from corresponding ACQ solutions, likely due to DDAC competition with copper for the same reaction sites.