Zdenek Folta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Interests
Zdenek Folta has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Miroslav Trochta
Department of Machine Parts and Mechanisms, Faculty of Mechanical Engineering, VSB—Technical University of Ostrava, 17. listopadu 2172/15, 70800 Ostrava, Czech Republic
5 shared publications - M. Burián
VSB—Technical University of Ostrava
3 shared publications - Pavel Marsalek
VSB—Technical University of Ostrava
3 shared publications - Jiri Struz
Faculty of Mechanical Engineering Department of Machine Parts and Mechanism VSB -Technical University of Ostrava 17. Listopadu 15/ 2172 CZ 708 33 Ostrava Czech Republic
2 shared publications - M. Hrudičková
VŚB-Technical University of Ostrava
2 shared publications - Daniel Pistacek
Faculty of Mechanical Engineering, VŠB—Technical University of Ostrava, 17. Listopadu 2172/15, 70800 Ostrava, Czech Republic
1 shared publication
Latest Publications
- 8 March 2023
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2023 (1) , 6354-6358
COMPARISON OF STANDARD AND NONSTANDARD GEAR ROOT FILLET CONSIDERING ROOT STRESS AND MANUFACTURING POSSIBILITIES
The MM Science Journal, published since 2008, is a world respected scientific journal. The journal, published in English, is double peer reviewed and competitive in distributing knowledge among domestic and international academics and professionals. Full texts are available on-line on the journal...
- 8 March 2023
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2023 (1) , 6354-6358
COMPARISON OF STANDARD AND NONSTANDARD GEAR ROOT FILLET CONSIDERING ROOT STRESS AND MANUFACTURING POSSIBILITIES
The MM Science Journal, published since 2008, is a world respected scientific journal. The journal, published in English, is double peer reviewed and competitive in distributing knowledge among domestic and international academics and professionals. Full texts are available on-line on the journal...
- Open Access
Influence of Symmetry of Tightened Parts on the Force in a Bolted Joint
This article discusses the issue of force behavior in a pre-tensioned bolt that is part of a symmetrical flange connection, loaded with an operating load parallel to the bolt axis. The first part describes the issue being dealt with in detail. The next part offers a brief description of the generally known theoretical approach to the solution, and also outlines the limitations of this approach. This part is followed by a theoretical analysis of working load behavior in the bolt of the analyzed device, using Finite Element Method (FEM). In this article, a comparison of several different approaches to the solution can be also found, followed by a description of the experiment preparation and its results. The obtained values also serve as a subject for reverse iterative analysis carried out using ANSYS software. The aim is to find a proper modification to the symmetric calculation model that would be consistent with the results of measurements from technical practice. All results achieved are described in the final part of the article.
Open AccessInfluence of Symmetry of Tightened Parts on the Force in a Bolted Joint
This article discusses the issue of force behavior in a pre-tensioned bolt that is part of a symmetrical flange connection, loaded with an operating load parallel to the bolt axis. The first part describes the issue being dealt with in detail. The next part offers a brief description of the generally known theoretical approach to the solution, and also outlines the limitations of this approach. This part is followed by a theoretical analysis of working load behavior in the bolt of the analyzed device, using Finite Element Method (FEM). In this article, a comparison of several different approaches to the solution can be also found, followed by a description of the experiment preparation and its results. The obtained values also serve as a subject for reverse iterative analysis carried out using ANSYS software. The aim is to find a proper modification to the symmetric calculation model that would be consistent with the results of measurements from technical practice. All results achieved are described in the final part of the article.
- 15 December 2021
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2021 (6) , 5396-5402
DETECTION OF MECHANICAL STRESS LIMITING EFFECTS OF CRANE STRUCTURE DEFORMATION
The paper presents a construction design and results of laboratory tests of so-called mechanical stress detectors, which can be used to detect the deformation of the steel structure of a crane and to amplify the mechanical signal from the effect of the so-called crane skewing, which is included a...
- 15 December 2021
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2021 (6) , 5396-5402
DETECTION OF MECHANICAL STRESS LIMITING EFFECTS OF CRANE STRUCTURE DEFORMATION
The paper presents a construction design and results of laboratory tests of so-called mechanical stress detectors, which can be used to detect the deformation of the steel structure of a crane and to amplify the mechanical signal from the effect of the so-called crane skewing, which is included a...
- 15 December 2021
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2021 (6) , 5391-5395
PROBABILISTIC ANALYSIS OF THE MAXIMAL LOAD OF INDUSTRIAL MACHINES
This study describes the statistical analysis of peak forces of industrial washing machines. The data source comes from twelve different machines. The measurements are done using a force gauge installed in places for fastening screws. A new software based on LabView has been developed to gauge the acting forces. To determine extreme force values, various probability distributions are applied. Furthermore, a convex combination of lognormal distribution is used in more complicated cases. The parameters of the lognormal mixtures are determined using modified an Expectation-maximization algorithm. Finally, the achieved results are interpreted with regard to the engineering design and to the operating reliability.
- 15 December 2021
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2021 (6) , 5391-5395
PROBABILISTIC ANALYSIS OF THE MAXIMAL LOAD OF INDUSTRIAL MACHINES
This study describes the statistical analysis of peak forces of industrial washing machines. The data source comes from twelve different machines. The measurements are done using a force gauge installed in places for fastening screws. A new software based on LabView has been developed to gauge the acting forces. To determine extreme force values, various probability distributions are applied. Furthermore, a convex combination of lognormal distribution is used in more complicated cases. The parameters of the lognormal mixtures are determined using modified an Expectation-maximization algorithm. Finally, the achieved results are interpreted with regard to the engineering design and to the operating reliability.
- 1 January 2016
- Published by Springer Nature
- p. 503-507
Contribution to the Methodology of Measuring Transmission Error
- 1 January 2016
- Published by Springer Nature
- p. 503-507
Contribution to the Methodology of Measuring Transmission Error
- 3 April 2014
- Published by Springer Nature
- p. 501-507
Design Assistance System (DASY)
- 3 April 2014
- Published by Springer Nature
- p. 399-404
Measuring of Torque on Testing Device for Measuring Transmission Error
- 3 April 2014
- Published by Springer Nature
- p. 399-404
Measuring of Torque on Testing Device for Measuring Transmission Error
- 3 April 2014
- Published by Springer Nature
- p. 335-341
Processing of Automobile Gearbox Load Spectra
- Open Access
- 1 December 2012
- Published by Czech Technical University in Prague - Central Library in Journal of Middle European Construction and Design of Cars
- Vol. 10 (3) , 22-30
Design Procedure for Loading Capacity Calculations for Classic Automobile Differentials
Shrnutí: Članek se zabyva navrhem dimenzovani ozubeni pro různe typy automobilnich diferencialů a děličů momentů. V navrženem postupu jsou použity nejnovějši vypočtove postupy podle norem ISO a DIN. Do vypočtu jsou aplikovana hypoteticka spektra provozniho zatiženi, ktera jsou odvozena od vlastnich měřeni.
- 1 December 2012
- Published by Czech Technical University in Prague - Central Library in Journal of Middle European Construction and Design of Cars
- Vol. 10 (3) , 22-30
Open AccessDesign Procedure for Loading Capacity Calculations for Classic Automobile Differentials
Shrnutí: Članek se zabyva navrhem dimenzovani ozubeni pro různe typy automobilnich diferencialů a děličů momentů. V navrženem postupu jsou použity nejnovějši vypočtove postupy podle norem ISO a DIN. Do vypočtu jsou aplikovana hypoteticka spektra provozniho zatiženi, ktera jsou odvozena od vlastnich měřeni.