Roland Jančo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Roland Jančo has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Ladislav Écsi
Slovak University of Technology in Bratislava , Faculty of Mechanical Engineering, Institute of Applied Mechanics and Mechatronics , Nám. slobody 17, 812 31 Bratislava , Slovakia
7 shared publications - Karel Frydrýšek
Department of Applied Mechanics, Faculty of Mechanical Engineering , VSB – Technical University of Ostrava , 17. listopadu 2172/15 , Ostrava – Poruba , Czech Republic
4 shared publications Pavel Élesztős
Lovak University of Technology in Bratislava
3 shared publications- Pavel Élesztős
Slovak University of Technology in Bratislava, Faculty of Mechanical Engineering, Institute of Applied Mechanics and Mechatronics, Nám. slobody 17, 812 31 Bratislava, Slovakia
3 shared publications - Peter Šlesar
Slovak University of Technology in Bratislava , Faculty of Mechanical Engineering , Institute of Applied Mechanics and Mechatronics , Nám. slobody 17, 812 31 Bratislava , Slovakia
3 shared publications - Andrej Chríbik
Slovak University of Technology in Bratislava , Faculty of Mechanical Engineering , Institute of Automotive Engineering and Design , Bratislava , Slovakia
2 shared publications
Latest Publications
- Open Access
- 1 November 2026
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 76 (2) , 54-74
An Alternative Mooney-Rivlin Material Model with a Plastic Spin for Finite Strain Plasticity
Contemporary finite-strain plasticity models that employ the multiplicative decomposition of the deformation gradient exhibit fundamental inconsistencies, as identified in our previous work, likely arising from a misinterpretation of elastoplastic deformation physics. We address these inconsistencies and extend our alternative Mooney–Rivlin model with plastic spin, based on additive strain-rate decomposition, demonstrating its consistency and suitability as a universal finite-strain elastoplastic framework.
- 1 November 2026
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 76 (2) , 54-74
Open AccessAn Alternative Mooney-Rivlin Material Model with a Plastic Spin for Finite Strain Plasticity
Contemporary finite-strain plasticity models that employ the multiplicative decomposition of the deformation gradient exhibit fundamental inconsistencies, as identified in our previous work, likely arising from a misinterpretation of elastoplastic deformation physics. We address these inconsistencies and extend our alternative Mooney–Rivlin model with plastic spin, based on additive strain-rate decomposition, demonstrating its consistency and suitability as a universal finite-strain elastoplastic framework.
- Open Access
- 1 September 2026
- Published by Walter de Gruyter GmbH in Acta Technologica Agriculturae
- Vol. 29 (3) , 204-211
Conversion of Turbocharged Internal Combustion Engine to Gaseous Fuel Used in Agricultural Machinery
This study focuses on the conversion of a turbocharged compression-ignition (diesel) engine UR-II 8602.12, originally installed in the Zetor 16145 tractor, into a spark-ignition (gas) unit operating on gaseous fuel. The study presents experimental results of performance, fuel economy, and emission characteristics under full-load speed sweep as well as part-load operation. The converted engine achieved a maximum corrected power output of 106.5 kW at 2200 rpm, representing an 8.5% reduction relative to the original diesel engine (116.5 kW). The corrected peak torque reached 462 N·m, which is 21% lower than the baseline diesel torque of 583 N·m. From an environmental perspective, carbon monoxide emissions remained very low (~0.05 vol. %), while hydrocarbon concentrations decreased with increasing mixture enrichment (from 377 ppm to 245 ppm). However, nitrogen oxides (NO x ) exceeded the threshold of 500 ppm across the entire speed range, peaking at 2282 ppm at the maximum speed. Exhaust gas temperatures behind the turbine reached up to 650 °C, which, after accounting for thermal gradient, implies that the recommended limit of 630 °C at exhaust valves is exceeded at higher loads. The findings demonstrate that natural gas conversion can retain favourable power characteristics while lowering carbon-based emissions, yet further optimisation is required to control thermal stress and mitigate NO x formation.
- 1 September 2026
- Published by Walter de Gruyter GmbH in Acta Technologica Agriculturae
- Vol. 29 (3) , 204-211
Open AccessConversion of Turbocharged Internal Combustion Engine to Gaseous Fuel Used in Agricultural Machinery
This study focuses on the conversion of a turbocharged compression-ignition (diesel) engine UR-II 8602.12, originally installed in the Zetor 16145 tractor, into a spark-ignition (gas) unit operating on gaseous fuel. The study presents experimental results of performance, fuel economy, and emission characteristics under full-load speed sweep as well as part-load operation. The converted engine achieved a maximum corrected power output of 106.5 kW at 2200 rpm, representing an 8.5% reduction relative to the original diesel engine (116.5 kW). The corrected peak torque reached 462 N·m, which is 21% lower than the baseline diesel torque of 583 N·m. From an environmental perspective, carbon monoxide emissions remained very low (~0.05 vol. %), while hydrocarbon concentrations decreased with increasing mixture enrichment (from 377 ppm to 245 ppm). However, nitrogen oxides (NO x ) exceeded the threshold of 500 ppm across the entire speed range, peaking at 2282 ppm at the maximum speed. Exhaust gas temperatures behind the turbine reached up to 650 °C, which, after accounting for thermal gradient, implies that the recommended limit of 630 °C at exhaust valves is exceeded at higher loads. The findings demonstrate that natural gas conversion can retain favourable power characteristics while lowering carbon-based emissions, yet further optimisation is required to control thermal stress and mitigate NO x formation.
- Open Access
- 1 April 2026
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 76 (1) , 79-88
Analysis of the Influence of Gas Composition from Renewable Energy Sources on the Integral Parameters of a Turbocharged Internal Combustion Engine
This study explores municipal waste-derived synthesis gas as a sustainable alternative fuel for internal combustion engines. Syngas properties, including lower heating value and combustion behavior, were linked to the feedstock characteristics and production method. Experimental investigations conducted on a turbocharged Lombardini LGW 702 spark-ignition engine showed that syngas mixtures with higher lower heating values (approximately 11–12 MJ/kg) achieved torque and mean effective pressure values close to those obtained with natural gas. In contrast, low-calorific syngases (approximately 8–9 MJ/kg) resulted in a torque reduction of about 6–15% and a significant increase in specific fuel consumption. The calculated specific energy of the stoichiometric fuel–air mixture ranged from approximately 2.3 to 2.8 MJ/kg under full-load conditions. The results confirm the technical feasibility of municipal waste-derived syngas for engine applications and its potential contribution to greenhouse gas reduction and the development of renewable energy systems.
- 1 April 2026
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 76 (1) , 79-88
Open AccessAnalysis of the Influence of Gas Composition from Renewable Energy Sources on the Integral Parameters of a Turbocharged Internal Combustion Engine
This study explores municipal waste-derived synthesis gas as a sustainable alternative fuel for internal combustion engines. Syngas properties, including lower heating value and combustion behavior, were linked to the feedstock characteristics and production method. Experimental investigations conducted on a turbocharged Lombardini LGW 702 spark-ignition engine showed that syngas mixtures with higher lower heating values (approximately 11–12 MJ/kg) achieved torque and mean effective pressure values close to those obtained with natural gas. In contrast, low-calorific syngases (approximately 8–9 MJ/kg) resulted in a torque reduction of about 6–15% and a significant increase in specific fuel consumption. The calculated specific energy of the stoichiometric fuel–air mixture ranged from approximately 2.3 to 2.8 MJ/kg under full-load conditions. The results confirm the technical feasibility of municipal waste-derived syngas for engine applications and its potential contribution to greenhouse gas reduction and the development of renewable energy systems.
- Open Access
- 6 October 2024
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 74 (2) , 43-48
Stress Analysis of Pressing Joint of Two Conical Pipes – Part 2
The paper presents a strength analysis of a pressed joint of two conical pipes with the aim of finding out whether this method of connection is suitable for telecommunication masts. In this paper, a solution using an engineering approach and a finite element method (FEM) numerical analysis for transversal direction will be compared.
- 6 October 2024
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 74 (2) , 43-48
Open AccessStress Analysis of Pressing Joint of Two Conical Pipes – Part 2
The paper presents a strength analysis of a pressed joint of two conical pipes with the aim of finding out whether this method of connection is suitable for telecommunication masts. In this paper, a solution using an engineering approach and a finite element method (FEM) numerical analysis for transversal direction will be compared.
- Open Access
- 1 May 2023
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 73 (1) , 117-124
Stress Analysis of Pressing Joint of Two Conical Pipes
This paper presents a stress analysis of a pressed joint of two conical pipes with the aim to find out whether this kind of connection is suitable for telecommunication masts. The analysis can be considered a complex spatial problem of a thin-walled shell, where the local bending stress influence might be dominant. In this paper a solution using engineering approach and numerical analysis with finite element method (FEM) will be compared.
- 1 May 2023
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 73 (1) , 117-124
Open AccessStress Analysis of Pressing Joint of Two Conical Pipes
This paper presents a stress analysis of a pressed joint of two conical pipes with the aim to find out whether this kind of connection is suitable for telecommunication masts. The analysis can be considered a complex spatial problem of a thin-walled shell, where the local bending stress influence might be dominant. In this paper a solution using engineering approach and numerical analysis with finite element method (FEM) will be compared.
- 10 September 2022
- Published by Springer Nature
- p. 925-932
Numerical Solution of the Aluminium Plate Welding Process by Friction Stir Welding
- 10 September 2022
- Published by Springer Nature
- p. 925-932
Numerical Solution of the Aluminium Plate Welding Process by Friction Stir Welding
- Open Access
- 17 June 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (12) , 5616
Mechanics of Screw Joints Solved as Beams Placed in a Tangential Elastic Foundation
This article deals with a new original analytical solution of deformation, force and stress states in wood screw joints up to the limit values of pulling out/breaking the screw. The screws are under tension. The wood-to-screw interaction is effectively simplified by introducing several physical model variants using a tangential elastic non-linear foundation. The experimental verification of the proposed models using pull-out tests (i.e., pulling out screws from dry spruce wood in laboratory conditions) confirms the correctness of the proposed models of the elastic linear/non-linear foundation. The validity of the model is also analytically and experimentally verified in the biomechanical model of pulling out screws from the femur of a bovine/human cadaver, which confirms and expands the validity of newly designed screw joint models outside the timber structure area.
- 17 June 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (12) , 5616
Open AccessMechanics of Screw Joints Solved as Beams Placed in a Tangential Elastic Foundation
This article deals with a new original analytical solution of deformation, force and stress states in wood screw joints up to the limit values of pulling out/breaking the screw. The screws are under tension. The wood-to-screw interaction is effectively simplified by introducing several physical model variants using a tangential elastic non-linear foundation. The experimental verification of the proposed models using pull-out tests (i.e., pulling out screws from dry spruce wood in laboratory conditions) confirms the correctness of the proposed models of the elastic linear/non-linear foundation. The validity of the model is also analytically and experimentally verified in the biomechanical model of pulling out screws from the femur of a bovine/human cadaver, which confirms and expands the validity of newly designed screw joint models outside the timber structure area.
- Open Access
- 1 April 2020
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 70 (1) , 103-114
Solution of a Gas Pipeline Buried in Ground by Stochastic Approach
The paper deals with stress and reliability calculation of a gas pipeline straight section buried in a ground (elastic foundation) loaded by heating and internal overpressure. Mathematical derivation of relations necessary for reliability calculation of the pipeline section by stochastic approach is also included in the paper. Resulting values are obtained by software Anthill using the Monte Carlo method. Input random parameters of the examined pipeline section are shown by bounded histograms.
- 1 April 2020
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 70 (1) , 103-114
Open AccessSolution of a Gas Pipeline Buried in Ground by Stochastic Approach
The paper deals with stress and reliability calculation of a gas pipeline straight section buried in a ground (elastic foundation) loaded by heating and internal overpressure. Mathematical derivation of relations necessary for reliability calculation of the pipeline section by stochastic approach is also included in the paper. Resulting values are obtained by software Anthill using the Monte Carlo method. Input random parameters of the examined pipeline section are shown by bounded histograms.
- Open Access
- 1 April 2020
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 70 (1) , 127-134
Strength and Dynamic Assessment of Cage and Bearing for Railway Carriage
The objective of these analyzes is to evaluate the behaviour of bearing cage in operation and to determinate the safety factor towards to yield and ultimate strength of structure, when cage is under load. Safety factor can be defined as force needed to achieve yield or ultimate strength divided by operation force given from dynamic simulation. Second analyze was based on pressing of whole cage in radial direction to determinate radial pressing force needed to achieve yield and ultimate strength.
- 1 April 2020
- Published by Walter de Gruyter GmbH in Strojnícky časopis - Journal of Mechanical Engineering
- Vol. 70 (1) , 127-134
Open AccessStrength and Dynamic Assessment of Cage and Bearing for Railway Carriage
The objective of these analyzes is to evaluate the behaviour of bearing cage in operation and to determinate the safety factor towards to yield and ultimate strength of structure, when cage is under load. Safety factor can be defined as force needed to achieve yield or ultimate strength divided by operation force given from dynamic simulation. Second analyze was based on pressing of whole cage in radial direction to determinate radial pressing force needed to achieve yield and ultimate strength.
- Open Access
- 13 May 2019
- Published by Ustav Teoreticke a Aplikovane Mechaniky AV CR
- p. 161-164
NUMERICAL SIMULATION OF FRICTION STIR WELDING OF ALUMINIUM PLATE
- 13 May 2019
- Published by Ustav Teoreticke a Aplikovane Mechaniky AV CR
- p. 161-164
Open AccessNUMERICAL SIMULATION OF FRICTION STIR WELDING OF ALUMINIUM PLATE