Masato Tsujikawa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Masato Tsujikawa has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Sachio Oki
Science and Engineering School of Kinki University, 3-4-1 Kowakae, Higashi-osaka, 577-8502, Japan
2 shared publicationsHironori Takahara
Department of Materials Science, Graduate School of Engineering, Osaka Prefecture University
1 shared publication- Kenji Higashi
Department of Materials Science, Graduate School of Engineering, Osaka Prefecture University
1 shared publication Masaichiro Kamita
Yamani Co. Ltd., Osaka, Japan
1 shared publicationSung-Wook Chung
Division of Technology Licensing Organization Osaka Prefecture
1 shared publicationTaiki Morishige
Department of Materials Science, Graduate School of Engineering, Osaka Prefecture University, 1-1 Gakuen-Cho Nakaku, Sakai, Osaka 599-8531, Japan
1 shared publication
Latest Publications
- Open Access
- 1 June 2009
- Published by Wiley in Plasma Processes and Polymers
- Vol. 6 (S1) , S954-S957
Thin Protective Aluminum Layer on Mg‐Li Alloy by Plasma Spraying and Cold Rolling
Formation of a protective thin surface of pure aluminum on Mg‐14mass%Li alloy by plasma thermal spraying and the cold rolling was investigated. An Mg‐14mass%Li‐1mass%Al alloy ingot was melted and cast in a pressurized argon atmosphere. After homogeneous heat treatment, the ingot was rolled to 3 mm‐thick plate with a reduction ratio of 98%. The plate specimens were annealed again. Plasma sprayings of pure aluminum were carried out with various conditions after grit blasting. The coated layer thickness was about 100 µm. There was slight increase in temperature during spraying on substrates. The first pass of rolling was carried out at 250 °C; then several cold rolling passes were processed to reduce the entire thickness up to 90% in reduction ratio of the sprayed specimens' thickness. It was found that the determining factor for sound rolled sheet without separation of aluminum coating was the maximum temperature of the substrate at plasma processing. There were no separation, for specimen heated in the temperature range between 300 and 400 °C during thermal spraying, at rolling up to 90% in total reduction ratio. Sectional observation revealed a continuous thin aluminum layer adhered on the Mg‐14mass%Li alloy.
- 1 June 2009
- Published by Wiley in Plasma Processes and Polymers
- Vol. 6 (S1) , S954-S957
Open AccessThin Protective Aluminum Layer on Mg‐Li Alloy by Plasma Spraying and Cold Rolling
Formation of a protective thin surface of pure aluminum on Mg‐14mass%Li alloy by plasma thermal spraying and the cold rolling was investigated. An Mg‐14mass%Li‐1mass%Al alloy ingot was melted and cast in a pressurized argon atmosphere. After homogeneous heat treatment, the ingot was rolled to 3 mm‐thick plate with a reduction ratio of 98%. The plate specimens were annealed again. Plasma sprayings of pure aluminum were carried out with various conditions after grit blasting. The coated layer thickness was about 100 µm. There was slight increase in temperature during spraying on substrates. The first pass of rolling was carried out at 250 °C; then several cold rolling passes were processed to reduce the entire thickness up to 90% in reduction ratio of the sprayed specimens' thickness. It was found that the determining factor for sound rolled sheet without separation of aluminum coating was the maximum temperature of the substrate at plasma processing. There were no separation, for specimen heated in the temperature range between 300 and 400 °C during thermal spraying, at rolling up to 90% in total reduction ratio. Sectional observation revealed a continuous thin aluminum layer adhered on the Mg‐14mass%Li alloy.
- Open Access
- 1 January 2008
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 49 (8) , 1911-1914
Optimum Processing and Tool Controls for Three-Dimensional Friction Stir Welding
- 1 January 2008
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 49 (8) , 1911-1914
Open AccessOptimum Processing and Tool Controls for Three-Dimensional Friction Stir Welding