Paweł Pełczyński
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Paweł Pełczyński has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Włodzimierz Szewczyk
Centre of Papermaking and Printing, Lodz University of Technology, Wólczańska 221, 95-003 Łódź, Poland
7 shared publications - Maria Bieńkowska
Centre of Papermaking and Printing, Lodz University of Technology, Wólczańska 221, 95-003 Łódź, Poland
4 shared publications - Dariusz Rzeszotarski
Lodz University of Technology
2 shared publications - Pawel Strumillo
Institute of Electronics, Lodz University of Technology, 90-924 Lodz, Poland
2 shared publications - Zbigniew Kolakowski
Department of Strength of Materials, Lodz University of Technology, Stefanowskiego 1/15, 90-537 Łódź, Poland
2 shared publications - Adam Łuc1 shared publication
Latest Publications
- 10 December 2025
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Pomiary Automatyka Robotyka
- Vol. 29 (4) , 127-137
Setting the Parameters of Corrugated Board Production Using Linear Models of Dependencies Between Process Variables
The article presents and compares selected techniques for the selection of parameters of the corrugated board production process based on linear models of relationships between process variables. The method of determining the parameters of these models is discussed, taking into account the practical knowledge and skills of operators conducting production. For this purpose, a system for measuring and recording the temperature of paper raw materials, the webs of the produced double-layer cardboard, the multi-layer board and the speed of the board of the produced cardboard was designed and installed in the industrial environment of the corrugator. The recorded data were analysed in order to develop and evaluate the suitability of selected models used to set initial parameters of cardboard production. The proposed approach allows the use of individual experience of each operator conducting production, which has a positive effect on the quality of the produced cardboard and the efficiency of the production process.
- 10 December 2025
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Pomiary Automatyka Robotyka
- Vol. 29 (4) , 127-137
Setting the Parameters of Corrugated Board Production Using Linear Models of Dependencies Between Process Variables
The article presents and compares selected techniques for the selection of parameters of the corrugated board production process based on linear models of relationships between process variables. The method of determining the parameters of these models is discussed, taking into account the practical knowledge and skills of operators conducting production. For this purpose, a system for measuring and recording the temperature of paper raw materials, the webs of the produced double-layer cardboard, the multi-layer board and the speed of the board of the produced cardboard was designed and installed in the industrial environment of the corrugator. The recorded data were analysed in order to develop and evaluate the suitability of selected models used to set initial parameters of cardboard production. The proposed approach allows the use of individual experience of each operator conducting production, which has a positive effect on the quality of the produced cardboard and the efficiency of the production process.
- Open Access
Numerical and Experimental Study into Paper Compression Test
The study aims to present the results of paper compression under an axial load. Different heights of samples subjected to compression were taken into account. The main goal of the analysis was to determine experimentally the maximum compression load. In addition, numerical models based on the finite element method (FEM) were validated to refer to empirical results. The performed numerical simulations were founded on Green–Lagrangian nonlinear equations for large displacements and strains. The progressive failure of the compressed orthotropic material after exceeding maximum stresses was based on Hill’s anisotropy theory. Nonlinear calculations were conducted by using a typical Newton–Raphson algorithm for achieving a sequence convergence. The accuracy of the developed model was confirmed experimentally in compression tests. The technique of analysing the shape of the compressed paper sample on the basis of images recorded during the measurement was used. The obtained test results are directly applicable in practice, especially in the calculation of the mechanical properties of corrugated cardboard and in determining the load capacity of cardboard packaging. Knowing the maximum compressive stress that packaging paper can withstand allows packaging to be properly designed and its strength assessed in the context of the transport and storage of goods.
Open AccessNumerical and Experimental Study into Paper Compression Test
The study aims to present the results of paper compression under an axial load. Different heights of samples subjected to compression were taken into account. The main goal of the analysis was to determine experimentally the maximum compression load. In addition, numerical models based on the finite element method (FEM) were validated to refer to empirical results. The performed numerical simulations were founded on Green–Lagrangian nonlinear equations for large displacements and strains. The progressive failure of the compressed orthotropic material after exceeding maximum stresses was based on Hill’s anisotropy theory. Nonlinear calculations were conducted by using a typical Newton–Raphson algorithm for achieving a sequence convergence. The accuracy of the developed model was confirmed experimentally in compression tests. The technique of analysing the shape of the compressed paper sample on the basis of images recorded during the measurement was used. The obtained test results are directly applicable in practice, especially in the calculation of the mechanical properties of corrugated cardboard and in determining the load capacity of cardboard packaging. Knowing the maximum compressive stress that packaging paper can withstand allows packaging to be properly designed and its strength assessed in the context of the transport and storage of goods.
- Open Access
Measurement and Control of Corrugated Board Production Parameters Taking into Account Individual Operator Preferences
The article presents a proposal for optimizing the production process of corrugated cardboard based on measurements of process variables as well as the knowledge and skills of the operator conducting production. This technique involves continuous recording and analysis of process quantities that affect the quality of the produced cardboard. For this purpose, a network of temperature sensors with a system of continuous registration and monitoring of the process variables was designed and installed in the industrial environment of the corrugator. The recorded data is analyzed to estimate the desired values of the measured process variables, giving clues to how to control the production line. Unlike existing systems, the proposed algorithm for controlling production parameters allows each operator to use their preferred values for process variables independently of others. The proposed system allows for improving the quality of the produced cardboard and increasing the efficiency of its production by taking into account the individual experience and habits of the operator conducting production.
Open AccessMeasurement and Control of Corrugated Board Production Parameters Taking into Account Individual Operator Preferences
The article presents a proposal for optimizing the production process of corrugated cardboard based on measurements of process variables as well as the knowledge and skills of the operator conducting production. This technique involves continuous recording and analysis of process quantities that affect the quality of the produced cardboard. For this purpose, a network of temperature sensors with a system of continuous registration and monitoring of the process variables was designed and installed in the industrial environment of the corrugator. The recorded data is analyzed to estimate the desired values of the measured process variables, giving clues to how to control the production line. Unlike existing systems, the proposed algorithm for controlling production parameters allows each operator to use their preferred values for process variables independently of others. The proposed system allows for improving the quality of the produced cardboard and increasing the efficiency of its production by taking into account the individual experience and habits of the operator conducting production.
- Open Access
New Models for Calculating the Maximum Compressive Force of Paper in Its Plane
The main objective of the presented research was to find a model that describes the maximum compressive force of paper in its plane. The research began with crushing tests of a number of packaging paper samples of various lengths. It was shown that due to the specific structure of the paper and the high heterogeneity of its structure, packaging paper is material where it is difficult to determine the maximum compressive stress. Next, three analytical models describing the load capacity of a flat paper web were investigated and an alternative empirical model was proposed. The results of the performed tests are directly applicable in the calculation of the mechanical properties of corrugated cardboard and the determination of the load capacity of cardboard packaging.
Open AccessNew Models for Calculating the Maximum Compressive Force of Paper in Its Plane
The main objective of the presented research was to find a model that describes the maximum compressive force of paper in its plane. The research began with crushing tests of a number of packaging paper samples of various lengths. It was shown that due to the specific structure of the paper and the high heterogeneity of its structure, packaging paper is material where it is difficult to determine the maximum compressive stress. Next, three analytical models describing the load capacity of a flat paper web were investigated and an alternative empirical model was proposed. The results of the performed tests are directly applicable in the calculation of the mechanical properties of corrugated cardboard and the determination of the load capacity of cardboard packaging.
- Open Access
- 20 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (3) , 1389
A New Technique for Determining the Shape of a Paper Sample in In-Plane Compression Test Using Image Sequence Analysis
The article presents a new technique for analyzing phenomena occurring during the measurement of the strength properties of paper in the conditions of compression of the tested samples with forces acting in the paper plane. The technique is based on collecting data on the current distance of the clamps holding the tested sample and the force exerted on the sample using a universal testing machine and on the simultaneous recording of image sequence of the sample during the measurement. Next, the resulting images are subjected to processing and analysis, the purpose of which is to extract information about the shape of the sample edge in all phases of the measurement. Its advantage is the ability to determine the deflection arrow of the sample and describe its shape using the selected function given by the analytical parametric formula. It will be helpful in further research on the development of an analytical model describing the phenomena occurring during paper compression, and a method to determine the mechanism of paper destruction and the corresponding maximum force that destroys a paper sample.
- 20 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (3) , 1389
Open AccessA New Technique for Determining the Shape of a Paper Sample in In-Plane Compression Test Using Image Sequence Analysis
The article presents a new technique for analyzing phenomena occurring during the measurement of the strength properties of paper in the conditions of compression of the tested samples with forces acting in the paper plane. The technique is based on collecting data on the current distance of the clamps holding the tested sample and the force exerted on the sample using a universal testing machine and on the simultaneous recording of image sequence of the sample during the measurement. Next, the resulting images are subjected to processing and analysis, the purpose of which is to extract information about the shape of the sample edge in all phases of the measurement. Its advantage is the ability to determine the deflection arrow of the sample and describe its shape using the selected function given by the analytical parametric formula. It will be helpful in further research on the development of an analytical model describing the phenomena occurring during paper compression, and a method to determine the mechanism of paper destruction and the corresponding maximum force that destroys a paper sample.
- 21 April 2021
- Published by Polish Academy of Sciences Chancellery in Metrology and Measurement Systems
- Vol. 28 (3) , 509-522
Single-camera system for measuring paper deformations based on image analysis
- 21 April 2021
- Published by Polish Academy of Sciences Chancellery in Metrology and Measurement Systems
- Vol. 28 (3) , 509-522
Single-camera system for measuring paper deformations based on image analysis
- Open Access
- 3 December 2018
- Published by EDP Sciences
- Vol. 70, 03006
Technical problems with compression units in mechanical vapour recompression systems
The evidence gathered during works on two prototype heat recovery systems is summarised. The first installation is a low-temperature vapour recompression system, whereas the second is a high-temperature (from an industrial viewpoint) installation. Vapour-contaminated air is the working medium. The authors focused their attention on machine issues mainly. All compressors described below were designed at the Lodz University of Technology.
- 3 December 2018
- Published by EDP Sciences
- Vol. 70, 03006
Open AccessTechnical problems with compression units in mechanical vapour recompression systems
The evidence gathered during works on two prototype heat recovery systems is summarised. The first installation is a low-temperature vapour recompression system, whereas the second is a high-temperature (from an industrial viewpoint) installation. Vapour-contaminated air is the working medium. The authors focused their attention on machine issues mainly. All compressors described below were designed at the Lodz University of Technology.
- 1 February 2018
- Published by Elsevier in Measurement
- Vol. 115, 52-63
Optical measurement of the hydrophobic properties of paper products
- 1 February 2018
- Published by Elsevier in Measurement
- Vol. 115, 52-63
Optical measurement of the hydrophobic properties of paper products
- 5 November 2016
- Published by Wydawnictwo SIGMA-NOT, sp. z.o.o. in PRZEGLĄD PAPIERNICZY
- Vol. 1 (11) , 63-69
Zastosowanie metod ter mowizyjnych do oceny procesu konsolidacji wstęgi w maszynie papier niczej
- 5 November 2016
- Published by Wydawnictwo SIGMA-NOT, sp. z.o.o. in PRZEGLĄD PAPIERNICZY
- Vol. 1 (11) , 63-69
Zastosowanie metod ter mowizyjnych do oceny procesu konsolidacji wstęgi w maszynie papier niczej
- 1 December 2012
- Published by Walter de Gruyter GmbH in Metrology and Measurement Systems
- Vol. 19 (4) , 805-816
Software Application for Calibration of Stereoscopic Camera Setups
The article describes an application for calibration of a stereovision camera setup constructed for the needs of an electronic travel aid for the blind. The application can be used to calibrate any stereovision system consisting of two DirectShow compatible cameras using a reference checkerboard of known dimensions. A method for experimental verification of the correctness of the calibration is also presented. The developed software is intended for calibration of mobile stereovision systems that focus mainly on obstacle detection.
- 1 December 2012
- Published by Walter de Gruyter GmbH in Metrology and Measurement Systems
- Vol. 19 (4) , 805-816
Software Application for Calibration of Stereoscopic Camera Setups
The article describes an application for calibration of a stereovision camera setup constructed for the needs of an electronic travel aid for the blind. The application can be used to calibrate any stereovision system consisting of two DirectShow compatible cameras using a reference checkerboard of known dimensions. A method for experimental verification of the correctness of the calibration is also presented. The developed software is intended for calibration of mobile stereovision systems that focus mainly on obstacle detection.