Leszek Matuszewski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Leszek Matuszewski has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Zbigniew Szydlo2 shared publications
- Krzysztof Falkowski
Avionics Department, Institute of Aviation Technology, Faculty of Mechatronics, Armament and Aerospace, Military University of Technology, Kaliskiego 2, 00-908 Warsaw, Poland
1 shared publication
Latest Publications
- Open Access
- 27 June 2017
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 24 (2) , 113-120
Failure of Magnetic Fluid Seals Operating in Water: Preliminary Conclusions
The article analyses properties of magnetic fluid seals installed in rotary sealing nodes which operate in the utility water environment. Seals of this type have been examined as a possible solution to the problem with ship manoeuvring propulsion sealing. The present analysis bases on laboratory durability tests of magnetic fluid seals exposed to longterm utility water loads, at different water pressures and shaft revolutions. The basic seal durability criterion was the number of revolutions made by the sealing node shaft until the appearance of water tightness loss (leakage). It was found that the main factor leading to the wear of the seal is the relative speed of the magnetic fluid with respect to that of the utility water, and this process is heavily affected by the pressure acting on the seal. The reported test results are presented in the form of diagrams showing the seal durability (time until water tightness loss) as a function of rotational speed. The curves shown in the diagrams are regular, with two different rotational speed ranges: the highspeed range, when the tightness loss is relatively fast, and the low-speed range, with a clear tendency to prolong the seal lifetime. These diagrams were given the name of durability curves of the MF seal operating in water. The results of the performed tests suggest formal similarity between the experimental data distribution concerning tightness loss processes occurring in magnetic fluid seals operating in water environment and metal fatigue processes. The article proposes a preliminary simplified durability model to describe the examined phenomenon.
- 27 June 2017
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 24 (2) , 113-120
Open AccessFailure of Magnetic Fluid Seals Operating in Water: Preliminary Conclusions
The article analyses properties of magnetic fluid seals installed in rotary sealing nodes which operate in the utility water environment. Seals of this type have been examined as a possible solution to the problem with ship manoeuvring propulsion sealing. The present analysis bases on laboratory durability tests of magnetic fluid seals exposed to longterm utility water loads, at different water pressures and shaft revolutions. The basic seal durability criterion was the number of revolutions made by the sealing node shaft until the appearance of water tightness loss (leakage). It was found that the main factor leading to the wear of the seal is the relative speed of the magnetic fluid with respect to that of the utility water, and this process is heavily affected by the pressure acting on the seal. The reported test results are presented in the form of diagrams showing the seal durability (time until water tightness loss) as a function of rotational speed. The curves shown in the diagrams are regular, with two different rotational speed ranges: the highspeed range, when the tightness loss is relatively fast, and the low-speed range, with a clear tendency to prolong the seal lifetime. These diagrams were given the name of durability curves of the MF seal operating in water. The results of the performed tests suggest formal similarity between the experimental data distribution concerning tightness loss processes occurring in magnetic fluid seals operating in water environment and metal fatigue processes. The article proposes a preliminary simplified durability model to describe the examined phenomenon.
- 1 December 2012
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 19 (4) , 62-70
Multi-stage magnetic-fluid seals for operating in water – life test procedure, test stand and research results
The edge criteria for magnetic-fluid seals durability research are critical for the seal’stechnological usefulness. The magnetic fluid seal technology in water is much moredifficult technological problem in comparison to gas or vacuum environment. There isalways problem with immediate contact between magnetic fluid and the environmentaluninspected liquids. In the paper are presented ways of experiments definitions carried outwith multi-stage rotating magnetic fluid seal operating in permanent contact with utilitywater. The special test procedures have been elaborated and practically used, with theaim to define main characteristics of magnetic fluid seals. These characteristics were: critical pressure,critical motion velocity and working life of the seal. Some grades of commercial, silicon based magneticfluids of hydrophobic properties were tested in sealing system. The test stand and its features as well asresults of tests are presented in the form of tables, cross section draws and diagrams. In conclusion onecan see that multi-stage magnetic-fluid seals could be efficiently used in water for rotating shaft seals ina limited range of motion velocity and work lasting.
- 1 December 2012
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 19 (4) , 62-70
Multi-stage magnetic-fluid seals for operating in water – life test procedure, test stand and research results
The edge criteria for magnetic-fluid seals durability research are critical for the seal’stechnological usefulness. The magnetic fluid seal technology in water is much moredifficult technological problem in comparison to gas or vacuum environment. There isalways problem with immediate contact between magnetic fluid and the environmentaluninspected liquids. In the paper are presented ways of experiments definitions carried outwith multi-stage rotating magnetic fluid seal operating in permanent contact with utilitywater. The special test procedures have been elaborated and practically used, with theaim to define main characteristics of magnetic fluid seals. These characteristics were: critical pressure,critical motion velocity and working life of the seal. Some grades of commercial, silicon based magneticfluids of hydrophobic properties were tested in sealing system. The test stand and its features as well asresults of tests are presented in the form of tables, cross section draws and diagrams. In conclusion onecan see that multi-stage magnetic-fluid seals could be efficiently used in water for rotating shaft seals ina limited range of motion velocity and work lasting.
- Open Access
- 1 January 2011
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 18 (2) , 51-59
Life tests of a rotary single-stage magnetic-fluid seal for shipbuilding applications
Use of the magnetic fluid seal technology in water is much more difficult technological problem in comparison to gas or vacuum environment. Some seals constructed up to time been are designed as hybrid, two stage sealing structures with shields or mechanical seals used as protection measures to the magnetic fluid seal. Anyway, there is always problem with immediate contact between magnetic fluid and the environmental liquid. In the paper are presented results of experiments carried out with one stage rotating magnetic fluid seal operating in immediate contact with utility water. The special test procedures have been elaborated and practically used, with the aim to define main characteristics of magnetic fluid seals and to simplify experiments. These characteristics were: critical pressure, critical motion velocity and working life of the seal. Four grades of commercial, silicon based magnetic fluids of hydrophobic properties were tested in a single stage sealing system. The results of tests are presented in the form of tables and diagrams. It is concluded that hydrophobic commercial magnetic fluids could be efficiently used in rotating shaft seals however in a limited range of motion velocity.
- 1 January 2011
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 18 (2) , 51-59
Open AccessLife tests of a rotary single-stage magnetic-fluid seal for shipbuilding applications
Use of the magnetic fluid seal technology in water is much more difficult technological problem in comparison to gas or vacuum environment. Some seals constructed up to time been are designed as hybrid, two stage sealing structures with shields or mechanical seals used as protection measures to the magnetic fluid seal. Anyway, there is always problem with immediate contact between magnetic fluid and the environmental liquid. In the paper are presented results of experiments carried out with one stage rotating magnetic fluid seal operating in immediate contact with utility water. The special test procedures have been elaborated and practically used, with the aim to define main characteristics of magnetic fluid seals and to simplify experiments. These characteristics were: critical pressure, critical motion velocity and working life of the seal. Four grades of commercial, silicon based magnetic fluids of hydrophobic properties were tested in a single stage sealing system. The results of tests are presented in the form of tables and diagrams. It is concluded that hydrophobic commercial magnetic fluids could be efficiently used in rotating shaft seals however in a limited range of motion velocity.
- Open Access
- 1 January 2010
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 17 (3) , 37-44
Mathematical model of radial passive magnetic bearing
In the article a mathematical model of radial passive magnetic bearings applicable to ocean engineering units has been presented. The application of the bearings in ship thrusters should increase durability of propulsion systems and give lower maintenance costs. The rotor of thruster's electric motor is suspended in magnetic field generated by radial passive magnetic bearings. However the maintaining of axial direction of the rotor must be controlled with electromagnets equipped with a high-dynamic controller. The risk of application of the magnetic bearings results from very low stiffness of the unit in comparison with rolling bearings. Also construction of the bearing should be different due to gyroscope effect and high forces generated during ship manoeuvring. The physical model performs correctly if electromagnets are controlled properly; and, technological problem with sealing system seems more significant than power supply to electromagnets winding. The equations presented in the article are necessary to build algorithms of a digital controller intended for on-line controlling magnetic bearing in axial direction.
- 1 January 2010
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 17 (3) , 37-44
Open AccessMathematical model of radial passive magnetic bearing
In the article a mathematical model of radial passive magnetic bearings applicable to ocean engineering units has been presented. The application of the bearings in ship thrusters should increase durability of propulsion systems and give lower maintenance costs. The rotor of thruster's electric motor is suspended in magnetic field generated by radial passive magnetic bearings. However the maintaining of axial direction of the rotor must be controlled with electromagnets equipped with a high-dynamic controller. The risk of application of the magnetic bearings results from very low stiffness of the unit in comparison with rolling bearings. Also construction of the bearing should be different due to gyroscope effect and high forces generated during ship manoeuvring. The physical model performs correctly if electromagnets are controlled properly; and, technological problem with sealing system seems more significant than power supply to electromagnets winding. The equations presented in the article are necessary to build algorithms of a digital controller intended for on-line controlling magnetic bearing in axial direction.
- 1 October 2008
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 15 (3) , 49-58
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment: Presented in article MF seals are being researched for sea technology purposes due to their excellent tightness and low resistance of motion. These features are most valuable for ring propellers and ship's main propeller shaft. There are more reasons why technologists payf significant attention for various MF seals applications in their difficult operating conditions. For instance, an advanced pumping systems are designed with contactless (screw or centrifugal) fluid seal used as the first stage seal and then the MF seal as the main seal. Further parts of the article contain discuss of the properties of magnetic fluids in the construction of MF seals. Sample of the few systems of magnetic fluid seals are presented, which have been researched lately in our laboratory including sea conditions. The magnetic fluids used in our seals are colloidal suspensions of magnetic nanoparticles. Undertaken earlier various systems selection for sea-water purposes forced us to focus on double sealing systems, in which the MF seal is used as the second seal following a conventional system especially adapted to co-operation with MF systems. This solution successfully limits direct contact of the sealed liquid with the magnetic fluid, and the entire sealing construction secures absolute tightness of the system. Using this solution we also can reduce costs by elements high accuracy avoidance. Research and design activities are carried out in the AGH Laboratory of Seals and Magnetic Fluid Applications together with Deep Water Department of Technical University of Gdansk over the use of magnetic fluid seals in sea water environment. These activities are oriented on working out MF seals able to work effectively in machines in which low-pressure water flow takes place. The objects of experimental investigations are seals having two different nominal diameters: 50 mm and 220 mm and two research rigs of different construction had to be built up. Works are scheduled to be continued.
- 1 October 2008
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 15 (3) , 49-58
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment: Presented in article MF seals are being researched for sea technology purposes due to their excellent tightness and low resistance of motion. These features are most valuable for ring propellers and ship's main propeller shaft. There are more reasons why technologists payf significant attention for various MF seals applications in their difficult operating conditions. For instance, an advanced pumping systems are designed with contactless (screw or centrifugal) fluid seal used as the first stage seal and then the MF seal as the main seal. Further parts of the article contain discuss of the properties of magnetic fluids in the construction of MF seals. Sample of the few systems of magnetic fluid seals are presented, which have been researched lately in our laboratory including sea conditions. The magnetic fluids used in our seals are colloidal suspensions of magnetic nanoparticles. Undertaken earlier various systems selection for sea-water purposes forced us to focus on double sealing systems, in which the MF seal is used as the second seal following a conventional system especially adapted to co-operation with MF systems. This solution successfully limits direct contact of the sealed liquid with the magnetic fluid, and the entire sealing construction secures absolute tightness of the system. Using this solution we also can reduce costs by elements high accuracy avoidance. Research and design activities are carried out in the AGH Laboratory of Seals and Magnetic Fluid Applications together with Deep Water Department of Technical University of Gdansk over the use of magnetic fluid seals in sea water environment. These activities are oriented on working out MF seals able to work effectively in machines in which low-pressure water flow takes place. The objects of experimental investigations are seals having two different nominal diameters: 50 mm and 220 mm and two research rigs of different construction had to be built up. Works are scheduled to be continued.